cannot boot system built today

Lee Harr missive at hotmail.com
Sat Jun 5 04:18:57 GMT 2004


>> > Not sure what else to show...  should I attach my serial console to get
>> > the cd boot messages?
>>
>>Yes please.
>>

Here is the boot -sv using the 4.10-RELEASE cd


SMAP type=01 base=0000000000000000 len=000000000009fc00
SMAP type=02 base=00000000000f0000 len=0000000000010000
SMAP type=02 base=00000000fec00000 len=0000000000001000
SMAP type=02 base=00000000fee00000 len=0000000000001000
SMAP type=02 base=00000000ffff0000 len=0000000000010000
SMAP type=02 base=000000000009fc00 len=0000000000000400
SMAP type=01 base=0000000000100000 len=000000001fef0000
SMAP type=03 base=000000001fff3000 len=000000000000d000
SMAP type=04 base=000000001fff0000 len=0000000000003000
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 4.10-RELEASE #0: Tue May 25 22:52:21 GMT 2004
    root at perseus.cse.buffalo.edu:/usr/obj/usr/src/sys/BOOTMFS
Calibrating clock(s) ... TSC clock: 1664112508 Hz, i8254 clock: 1193157 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254"  frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
Timecounter "TSC"  frequency 1664158122 Hz
CPU: AMD Athlon(tm) XP 2000+ (1664.16-MHz 686-class CPU)
  Origin = "AuthenticAMD"  Id = 0x680  Stepping = 0
  
Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
  AMD Features=0xc0400000<AMIE,DSP,3DNow!>
Data TLB: 32 entries, fully associative
Instruction TLB: 16 entries, fully associative
L1 data cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L1 instruction cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way 
associative
L2 internal cache: 256 kbytes, 64 bytes/line, 1 lines/tag, 8-way associative
real memory  = 536805376 (524224K bytes)
Physical memory chunk(s):
0x000001000 - 0x00009efff, 647168 bytes (158 pages)
0x000850000 - 0x01ffe7fff, 528056320 bytes (128920 pages)
config> intro
[snip kernel config screen]
avail memory = 514338816 (502284K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00faff0
bios32: Entry = 0xfb480 (c00fb480)  Rev = 0  Len = 1
pcibios: PCI BIOS entry at 0xb4b0
pnpbios: Found PnP BIOS data at 0xc00fbf20
pnpbios: Entry = f0000:bf50  Rev = 1.0
Other BIOS signatures found:
ACPI: 000f6d80
Preloaded elf kernel "kernel" at 0xc0829000.
Preloaded mfs_root "/mfsroot" at 0xc0829090.
Pentium Pro MTRR support enabled
md0: Preloaded image </mfsroot> 4423680 bytes at 0xc03ef3d4
Creating DISK md0
Creating DISK md1
md1: Malloc disk
Math emulator present
pci_open(1):	mode 1 addr port (0x0cf8) is 0x80000888
pci_open(1a):	mode1res=0x80000000 (0x80000000)
pci_cfgcheck:	device 0 [class=060000] [hdr=80] is there (id=01e010de)
Using $PIR table, 11 entries at 0xc00fdeb0
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
found->	vendor=0x10de, dev=0x01e0, revid=0xa2
	class=06-00-00, hdrtype=0x00, mfdev=1
	subordinatebus=0 	secondarybus=0
	map[10]: type 1, range 32, base e0000000, size 26
found->	vendor=0x10de, dev=0x01eb, revid=0xa2
	class=05-00-00, hdrtype=0x00, mfdev=1
	subordinatebus=0 	secondarybus=0
found->	vendor=0x10de, dev=0x01ee, revid=0xa2
	class=05-00-00, hdrtype=0x00, mfdev=1
	subordinatebus=0 	secondarybus=0
found->	vendor=0x10de, dev=0x01ed, revid=0xa2
	class=05-00-00, hdrtype=0x00, mfdev=1
	subordinatebus=0 	secondarybus=0
found->	vendor=0x10de, dev=0x01ec, revid=0xa2
	class=05-00-00, hdrtype=0x00, mfdev=1
	subordinatebus=0 	secondarybus=0
found->	vendor=0x10de, dev=0x01ef, revid=0xa2
	class=05-00-00, hdrtype=0x00, mfdev=1
	subordinatebus=0 	secondarybus=0
found->	vendor=0x10de, dev=0x0060, revid=0xa3
	class=06-01-00, hdrtype=0x00, mfdev=1
	subordinatebus=0 	secondarybus=0
found->	vendor=0x10de, dev=0x0064, revid=0xa2
	class=0c-05-00, hdrtype=0x00, mfdev=1
	subordinatebus=0 	secondarybus=0
	intpin=a, irq=255
	map[10]: type 1, range 32, base 0000e000, size  5
found->	vendor=0x10de, dev=0x0067, revid=0xa3
	class=0c-03-10, hdrtype=0x00, mfdev=1
	subordinatebus=0 	secondarybus=0
	intpin=a, irq=5
	map[10]: type 1, range 32, base ed087000, size 12
found->	vendor=0x10de, dev=0x0067, revid=0xa3
	class=0c-03-10, hdrtype=0x00, mfdev=1
	subordinatebus=0 	secondarybus=0
	intpin=b, irq=3
	map[10]: type 1, range 32, base ed082000, size 12
found->	vendor=0x10de, dev=0x0068, revid=0xa3
	class=0c-03-20, hdrtype=0x00, mfdev=1
	subordinatebus=0 	secondarybus=0
	intpin=c, irq=5
	map[10]: type 1, range 32, base ed083000, size  8
found->	vendor=0x10de, dev=0x0066, revid=0xa1
	class=02-00-00, hdrtype=0x00, mfdev=0
	subordinatebus=0 	secondarybus=0
	intpin=a, irq=3
	map[10]: type 1, range 32, base ed086000, size 12
	map[14]: type 1, range 32, base 0000e400, size  3
found->	vendor=0x10de, dev=0x006b, revid=0xa2
	class=04-01-00, hdrtype=0x00, mfdev=0
	subordinatebus=0 	secondarybus=0
	intpin=a, irq=3
	map[10]: type 1, range 32, base ed000000, size 19
found->	vendor=0x10de, dev=0x006a, revid=0xa1
	class=04-01-00, hdrtype=0x00, mfdev=0
	subordinatebus=0 	secondarybus=0
	intpin=a, irq=5
	map[10]: type 1, range 32, base 0000d000, size  8
	map[14]: type 1, range 32, base 0000d400, size  7
	map[18]: type 1, range 32, base ed080000, size 12
found->	vendor=0x10de, dev=0x006c, revid=0xa3
	class=06-04-00, hdrtype=0x01, mfdev=0
	subordinatebus=1 	secondarybus=1
found->	vendor=0x10de, dev=0x0065, revid=0xa2
	class=01-01-8a, hdrtype=0x00, mfdev=0
	subordinatebus=0 	secondarybus=0
	map[20]: type 1, range 32, base 0000f000, size  4
found->	vendor=0x10de, dev=0x006d, revid=0xa3
	class=06-04-00, hdrtype=0x01, mfdev=0
	subordinatebus=2 	secondarybus=2
found->	vendor=0x10de, dev=0x006e, revid=0xa3
	class=0c-00-10, hdrtype=0x00, mfdev=0
	subordinatebus=0 	secondarybus=0
	intpin=a, irq=11
	map[10]: type 1, range 32, base ed084000, size 11
	map[14]: type 1, range 32, base ed085000, size  6
found->	vendor=0x10de, dev=0x01e8, revid=0xa2
	class=06-04-00, hdrtype=0x01, mfdev=0
	subordinatebus=3 	secondarybus=3
pci0: <PCI bus> on pcib0
pci0: <unknown card> (vendor=0x10de, dev=0x01eb) at 0.1
pci0: <unknown card> (vendor=0x10de, dev=0x01ee) at 0.2
pci0: <unknown card> (vendor=0x10de, dev=0x01ed) at 0.3
pci0: <unknown card> (vendor=0x10de, dev=0x01ec) at 0.4
pci0: <unknown card> (vendor=0x10de, dev=0x01ef) at 0.5
isab0: <PCI to ISA bridge (vendor=10de device=0060)> at device 1.0 on pci0
isa0: <ISA bus> on isab0
pci0: <unknown card> (vendor=0x10de, dev=0x0064) at 1.1
ohci0: <OHCI (generic) USB controller> mem 0xed087000-0xed087fff irq 5 at 
device 2.0 on pci0
ohci0: (New OHCI DeviceId=0x006710de)
usb0: OHCI version 1.0, legacy support
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: (0x10de) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
ohci1: <OHCI (generic) USB controller> mem 0xed082000-0xed082fff irq 3 at 
device 2.1 on pci0
ohci1: (New OHCI DeviceId=0x006710de)
usb1: OHCI version 1.0, legacy support
usb1: <OHCI (generic) USB controller> on ohci1
usb1: USB revision 1.0
uhub1: (0x10de) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 3 ports with 3 removable, self powered
pci0: <USB controller> (vendor=0x10de, dev=0x0068) at 2.2 irq 5
pci0: <unknown card> (vendor=0x10de, dev=0x0066) at 4.0 irq 3
pci0: <unknown card> (vendor=0x10de, dev=0x006b) at 5.0 irq 3
pci0: <unknown card> (vendor=0x10de, dev=0x006a) at 6.0 irq 5
pcib1: <PCI to PCI bridge (vendor=10de device=006c)> at device 8.0 on pci0
found->	vendor=0x1095, dev=0x3112, revid=0x02
	class=01-04-00, hdrtype=0x00, mfdev=0
	subordinatebus=0 	secondarybus=0
	intpin=a, irq=11
	map[10]: type 1, range 32, base 0000a000, size  3
	map[14]: type 1, range 32, base 0000a400, size  2
	map[18]: type 1, range 32, base 0000a800, size  3
	map[1c]: type 1, range 32, base 0000ac00, size  2
	map[20]: type 1, range 32, base 0000b000, size  4
	map[24]: type 1, range 32, base ec000000, size  9
pci1: <PCI bus> on pcib1
pci1: <unknown card> (vendor=0x1095, dev=0x3112) at 11.0 irq 11
atapci0: <nVIDIA nForce2 ATA133 controller> port 0xf000-0xf00f at device 9.0 
on pci0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0xf000
ata0: mask=03 ostat0=50 ostat2=50
ata0-master: ATAPI 00 00
ata0-slave: ATAPI 00 00
ata0: mask=03 stat0=50 stat1=50
ata0-master: ATA 01 a5
ata0-slave: ATA 01 a5
ata0: devices=03
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0xf008
ata1: mask=03 ostat0=50 ostat2=00
ata1-master: ATAPI 14 eb
ata1-slave: ATAPI 00 00
ata1: mask=03 stat0=00 stat1=00
ata1: devices=04
ata1: at 0x170 irq 15 on atapci0
pcib2: <PCI to PCI bridge (vendor=10de device=006d)> at device 12.0 on pci0
found->	vendor=0x10b7, dev=0x9201, revid=0x40
	class=02-00-00, hdrtype=0x00, mfdev=0
	subordinatebus=0 	secondarybus=0
	intpin=a, irq=5
	map[10]: type 1, range 32, base 0000c000, size  7
	map[14]: type 1, range 32, base e7000000, size  7
pci2: <PCI bus> on pcib2
xl0: <3Com 3c920B-EMB Integrated Fast Etherlink XL> port 0xc000-0xc07f mem 
0xe7000000-0xe700007f irq 5 at device 1.0 on pci2
xl0: using port I/O
xl0: Ethernet address: 00:26:54:0a:df:a2
xl0: media options word: 40
xl0: found MII/AUTO
miibus0: <MII bus> on xl0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: OUI 0x000895, model 0x0012, rev. 1
ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: xl0 attached
	using shared irq5.
pci0: <unknown card> (vendor=0x10de, dev=0x006e) at 13.0 irq 11
pcib3: <PCI to PCI bridge (vendor=10de device=01e8)> at device 30.0 on pci0
found->	vendor=0x102b, dev=0x0525, revid=0x85
	class=03-00-00, hdrtype=0x00, mfdev=0
	subordinatebus=0 	secondarybus=0
	intpin=a, irq=11
	map[10]: type 1, range 32, base e4000000, size 25
	map[14]: type 1, range 32, base e8000000, size 14
	map[18]: type 1, range 32, base e9000000, size 23
pci3: <PCI bus> on pcib3
pci3: <Matrox MGA G400 AGP graphics accelerator> (vendor=0x102b, dev=0x0525) 
at 0.0 irq 11
ex_isa_identify()
ata-: ata0 exists, using next available unit number
ata-: ata1 exists, using next available unit number
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem 0xc0000-0xc87ff,0xcc000-0xcd7ff,0xce000-0xce7ff 
on isa0
pmtimer0 on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
ata2 failed to probe at port 0x1f0 irq 14 on isa0
ata3 failed to probe at port 0x170 irq 15 on isa0
adv0 failed to probe on isa0
bt0: Failed Status Reg Test - fe
bt_isa_probe: Probe failed at 0x330
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x334
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x230
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x234
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x130
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x134
bt0 failed to probe at port 0x134-0x137 on isa0
aha0: status reg test failed fe
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0 failed to probe at port 0x134-0x137 on isa0
aic0 failed to probe at port 0x140-0x15f on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x1d0000
psm0: current command byte:0047
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
psm: status 00 02 64
psm: status 00 03 06
psm: status 00 33 55
psm: data 08 00 00
psm: status 00 02 64
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model NetMouse/NetScroll Optical, device ID 0-00, 3 buttons
psm0: config:00000000, flags:00000000, packet size:4
psm0: syncmask:08, syncbits:08
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0e 0f 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
sio0: irq maps: 0x1 0x11 0x1 0x1
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: irq maps: 0x1 0x1 0x1 0x1
sio1: probe failed test(s): 0 1 2 4 6 7 9
sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
ppc0: parallel port found at 0x378
ppc0: using extended I/O port range
ppc0: EPP SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
bpf: lp0 attached
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
cs0: not probed (disabled)
sn0: not probed (disabled)
isa_probe_children: probing PnP devices
BIOS Geometries:
0:03fffe3f 0..1023=1024 cylinders, 0..254=255 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
bpf: lo0 attached
bpf: sl0 attached
ad0: success setting UDMA5 on nVIDIA chip
Creating DISK ad0
ar: FreeBSD check1 failed
ad0: <WDC WD800JB-00ETA0/77.07W77> ATA-6 disk at ata0-master
ad0: 76319MB (156301488 sectors), 155061 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA100
ad0: piomode=4 dmamode=2 udmamode=5 cblid=1
ad1: success setting UDMA5 on nVIDIA chip
Creating DISK ad1
ar: FreeBSD check1 failed
ad1: <WDC WD400BB-60BNA1/18.20D18> ATA-5 disk at ata0-slave
ad1: 38166MB (78165360 sectors), 77545 C, 16 H, 63 S, 512 B
ad1: 16 secs/int, 1 depth queue, UDMA100
ad1: piomode=4 dmamode=2 udmamode=5 cblid=1
ata1-master: piomode=4 dmamode=2 udmamode=2 dmaflag=1
ata1-master: success setting PIO4 on generic chip
acd0: <LITE-ON LTR-52246S/6S0C> CD-RW drive at ata1 as master
acd0: read 1375KB/s (48034KB/s) write 8937KB/s (8937KB/s), 2048KB buffer, 
PIO4
acd0: Reads: CD-R, CD-RW, CD-DA stream, packet
acd0: Writes: CD-R, CD-RW, test write, burnproof
acd0: Audio: play, 255 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: CD-R 120mm data disc
Mounting root from ufs:/dev/md0c
start_init: trying /sbin/init
start_init: trying /sbin/oinit
start_init: trying /sbin/init.bak
start_init: trying /stand/sysinstall
/stand/sysinstall running as init on serial console

These are the predefined terminal types available to
sysinstall when running stand-alone.  Please choose the
closest match for your particular terminal.

1 ...................... Standard ANSI terminal.
2 ...................... VT100 or compatible terminal.
3 ...................... FreeBSD system console (color).
4 ...................... FreeBSD system console (monochrome).

5 ...................... xterm terminal emulator.

Your choice: (1-5) 1
fwohci0: vendor=10de, dev=6e
fwohci0: <1394 Open Host Controller Interface> mem 
0xed085000-0xed08503f,0xed084000-0xed0847ff irq 11 at device 13.0 on pci0
fwohci0: latency timer 0 -> 32.
fwohci0: cache size 0 -> 8.
	using shared irq11.
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channel is 4.
fwohci0: EUI64 00:e0:18:00:00:16:af:0a
fwohci0: resetting OHCI...done (loop=0)
fwohci0: fwphy_rddata: 0x2 loop=1, retry=0
fwohci0: fwphy_rddata: 0x3 loop=1, retry=0
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: fwphy_rddata: 0x5 loop=1, retry=0
fwohci0: Enable 1394a Enhancements
fwohci0: fwphy_rddata: 0x5 loop=1, retry=0
fwohci0: fwphy_rddata: 0x2 loop=1, retry=0
fwohci0: fwphy_rddata: 0x4 loop=1, retry=0
fwohci0: fwphy_rddata: 0x4 loop=1, retry=0
fwohci0: fwphy_rddata: 0x4 loop=1, retry=0
fwohci0: Link S400, max_rec 2048 bytes.
fwohci0: BUS_OPT 0xf864a232 -> 0xf864a232
fwohci0: fwohci_set_intr: 1
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwohci0: Initiate bus reset
fwohci0: fwphy_rddata: 0x1 loop=1, retry=0
fwohci0: fwphy_rddata: 0x1 loop=1, retry=0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:e0:18:16:af:0a
bpf: fwe0 attached
sbp0: <SBP-2/SCSI over FireWire> on firewire0
sbp_attach (cold=0)
sbp_post_busreset
sbp_post_explore (sbp_cold=1)
aha0: status reg test failed ff
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: irq maps: 0x105 0x105 0x105 0x105
sio1: probe failed test(s): 0 1 2 4 6 7 9




>>Also, Lite-on drives are known to have buggy firmware. Does removing the
>>CDROM drive make it boot?
>>


No. That does not help. Here is the boot message with the cd drive
disconnected:


SMAP type=01 base=0000000000000000 len=000000000009fc00
SMAP type=02 base=00000000000f0000 len=0000000000010000
SMAP type=02 base=00000000fec00000 len=0000000000001000
SMAP type=02 base=00000000fee00000 len=0000000000001000
SMAP type=02 base=00000000ffff0000 len=0000000000010000
SMAP type=02 base=000000000009fc00 len=0000000000000400
SMAP type=01 base=0000000000100000 len=000000001fef0000
SMAP type=03 base=000000001fff3000 len=000000000000d000
SMAP type=04 base=000000001fff0000 len=0000000000003000
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD 4.10-STABLE #2: Fri May 28 02:16:56 EDT 2004
    lee at homer:/mnt/obj/mnt/src/sys/GENERIC
Calibrating clock(s) ... TSC clock: 1664107303 Hz, i8254 clock: 1193153 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254"  frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
CPU: AMD Athlon(tm) XP 2000+ (1664.15-MHz 686-class CPU)
  Origin = "AuthenticAMD"  Id = 0x680  Stepping = 0
  
Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
  AMD Features=0xc0400000<AMIE,DSP,3DNow!>
Data TLB: 32 entries, fully associative
Instruction TLB: 16 entries, fully associative
L1 data cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative
L1 instruction cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way 
associative
L2 internal cache: 256 kbytes, 64 bytes/line, 1 lines/tag, 8-way associative
real memory  = 536805376 (524224K bytes)
Physical memory chunk(s):
0x000001000 - 0x00009efff, 647168 bytes (158 pages)
0x000592000 - 0x01ffe7fff, 530931712 bytes (129622 pages)
avail memory = 516767744 (504656K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00faff0
bios32: Entry = 0xfb480 (c00fb480)  Rev = 0  Len = 1
pcibios: PCI BIOS entry at 0xb4b0
pnpbios: Found PnP BIOS data at 0xc00fbf20
pnpbios: Entry = f0000:bf50  Rev = 1.0
Other BIOS signatures found:
ACPI: 000f6d80
Preloaded elf kernel "kernel" at 0xc056b000.
Preloaded elf module "linux.ko" at 0xc056b0a8.
Pentium Pro MTRR support enabled
Creating DISK md0
md0: Malloc disk
Math emulator present
pci_open(1):	mode 1 addr port (0x0cf8) is 0x00000000
pci_open(1a):	mode1res=0x80000000 (0x80000000)
pci_cfgcheck:	device 0 [class=060000] [hdr=80] is there (id=01e010de)
Using $PIR table, 11 entries at 0xc00fdeb0
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
found->	vendor=0x10de, dev=0x01e0, revid=0xa2
	class=06-00-00, hdrtype=0x00, mfdev=1
	subordinatebus=0 	secondarybus=0
	map[10]: type 1, range 32, base e0000000, size 26
found->	vendor=0x10de, dev=0x01eb, revid=0xa2
	class=05-00-00, hdrtype=0x00, mfdev=1
	subordinatebus=0 	secondarybus=0
found->	vendor=0x10de, dev=0x01ee, revid=0xa2
	class=05-00-00, hdrtype=0x00, mfdev=1
	subordinatebus=0 	secondarybus=0
found->	vendor=0x10de, dev=0x01ed, revid=0xa2
	class=05-00-00, hdrtype=0x00, mfdev=1
	subordinatebus=0 	secondarybus=0
found->	vendor=0x10de, dev=0x01ec, revid=0xa2
	class=05-00-00, hdrtype=0x00, mfdev=1
	subordinatebus=0 	secondarybus=0
found->	vendor=0x10de, dev=0x01ef, revid=0xa2
	class=05-00-00, hdrtype=0x00, mfdev=1
	subordinatebus=0 	secondarybus=0
found->	vendor=0x10de, dev=0x0060, revid=0xa3
	class=06-01-00, hdrtype=0x00, mfdev=1
	subordinatebus=0 	secondarybus=0
found->	vendor=0x10de, dev=0x0064, revid=0xa2
	class=0c-05-00, hdrtype=0x00, mfdev=1
	subordinatebus=0 	secondarybus=0
	intpin=a, irq=255
	map[10]: type 1, range 32, base 0000e000, size  5
found->	vendor=0x10de, dev=0x0067, revid=0xa3
	class=0c-03-10, hdrtype=0x00, mfdev=1
	subordinatebus=0 	secondarybus=0
	intpin=a, irq=5
	map[10]: type 1, range 32, base ed087000, size 12
found->	vendor=0x10de, dev=0x0067, revid=0xa3
	class=0c-03-10, hdrtype=0x00, mfdev=1
	subordinatebus=0 	secondarybus=0
	intpin=b, irq=3
	map[10]: type 1, range 32, base ed082000, size 12
found->	vendor=0x10de, dev=0x0068, revid=0xa3
	class=0c-03-20, hdrtype=0x00, mfdev=1
	subordinatebus=0 	secondarybus=0
	intpin=c, irq=5
	map[10]: type 1, range 32, base ed083000, size  8
found->	vendor=0x10de, dev=0x0066, revid=0xa1
	class=02-00-00, hdrtype=0x00, mfdev=0
	subordinatebus=0 	secondarybus=0
	intpin=a, irq=3
	map[10]: type 1, range 32, base ed086000, size 12
	map[14]: type 1, range 32, base 0000e400, size  3
found->	vendor=0x10de, dev=0x006b, revid=0xa2
	class=04-01-00, hdrtype=0x00, mfdev=0
	subordinatebus=0 	secondarybus=0
	intpin=a, irq=3
	map[10]: type 1, range 32, base ed000000, size 19
found->	vendor=0x10de, dev=0x006a, revid=0xa1
	class=04-01-00, hdrtype=0x00, mfdev=0
	subordinatebus=0 	secondarybus=0
	intpin=a, irq=5
	map[10]: type 1, range 32, base 0000d000, size  8
	map[14]: type 1, range 32, base 0000d400, size  7
	map[18]: type 1, range 32, base ed080000, size 12
found->	vendor=0x10de, dev=0x006c, revid=0xa3
	class=06-04-00, hdrtype=0x01, mfdev=0
	subordinatebus=1 	secondarybus=1
found->	vendor=0x10de, dev=0x0065, revid=0xa2
	class=01-01-8a, hdrtype=0x00, mfdev=0
	subordinatebus=0 	secondarybus=0
	map[20]: type 1, range 32, base 0000f000, size  4
found->	vendor=0x10de, dev=0x006d, revid=0xa3
	class=06-04-00, hdrtype=0x01, mfdev=0
	subordinatebus=2 	secondarybus=2
found->	vendor=0x10de, dev=0x006e, revid=0xa3
	class=0c-00-10, hdrtype=0x00, mfdev=0
	subordinatebus=0 	secondarybus=0
	intpin=a, irq=11
	map[10]: type 1, range 32, base ed084000, size 11
	map[14]: type 1, range 32, base ed085000, size  6
found->	vendor=0x10de, dev=0x01e8, revid=0xa2
	class=06-04-00, hdrtype=0x01, mfdev=0
	subordinatebus=3 	secondarybus=3
pci0: <PCI bus> on pcib0
pci0: <unknown card> (vendor=0x10de, dev=0x01eb) at 0.1
pci0: <unknown card> (vendor=0x10de, dev=0x01ee) at 0.2
pci0: <unknown card> (vendor=0x10de, dev=0x01ed) at 0.3
pci0: <unknown card> (vendor=0x10de, dev=0x01ec) at 0.4
pci0: <unknown card> (vendor=0x10de, dev=0x01ef) at 0.5
isab0: <PCI to ISA bridge (vendor=10de device=0060)> at device 1.0 on pci0
isa0: <ISA bus> on isab0
pci0: <unknown card> (vendor=0x10de, dev=0x0064) at 1.1
ohci0: <OHCI (generic) USB controller> mem 0xed087000-0xed087fff irq 5 at 
device 2.0 on pci0
ohci0: (New OHCI DeviceId=0x006710de)
usb0: OHCI version 1.0, legacy support
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: (0x10de) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
ohci1: <OHCI (generic) USB controller> mem 0xed082000-0xed082fff irq 3 at 
device 2.1 on pci0
ohci1: (New OHCI DeviceId=0x006710de)
usb1: OHCI version 1.0, legacy support
usb1: <OHCI (generic) USB controller> on ohci1
usb1: USB revision 1.0
uhub1: (0x10de) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 3 ports with 3 removable, self powered
pci0: <USB controller> (vendor=0x10de, dev=0x0068) at 2.2 irq 5
pci0: <unknown card> (vendor=0x10de, dev=0x0066) at 4.0 irq 3
pci0: <unknown card> (vendor=0x10de, dev=0x006b) at 5.0 irq 3
pci0: <unknown card> (vendor=0x10de, dev=0x006a) at 6.0 irq 5
pcib1: <PCI to PCI bridge (vendor=10de device=006c)> at device 8.0 on pci0
found->	vendor=0x1095, dev=0x3112, revid=0x02
	class=01-04-00, hdrtype=0x00, mfdev=0
	subordinatebus=0 	secondarybus=0
	intpin=a, irq=11
	map[10]: type 1, range 32, base 0000a000, size  3
	map[14]: type 1, range 32, base 0000a400, size  2
	map[18]: type 1, range 32, base 0000a800, size  3
	map[1c]: type 1, range 32, base 0000ac00, size  2
	map[20]: type 1, range 32, base 0000b000, size  4
	map[24]: type 1, range 32, base ec000000, size  9
pci1: <PCI bus> on pcib1
pci1: <unknown card> (vendor=0x1095, dev=0x3112) at 11.0 irq 11
atapci0: <nVIDIA nForce2 ATA133 controller> port 0xf000-0xf00f at device 9.0 
on pci0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0xf000
ata0: mask=03 ostat0=50 ostat2=50
ata0-master: ATAPI 00 00
ata0-slave: ATAPI 00 00
ata0: mask=03 stat0=50 stat1=50
ata0-master: ATA 01 a5
ata0-slave: ATA 01 a5
ata0: devices=03
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0xf008
ata1: mask=03 ostat0=20 ostat2=30
ata1-master: ATAPI 20 20
ata1-slave: ATAPI 30 30
ata1: mask=03 stat0=20 stat1=30
ata1-master: ATA 25 25
ata1-slave: ATA 25 25
ata1: devices=00
ata1: at 0x170 irq 15 on atapci0
pcib2: <PCI to PCI bridge (vendor=10de device=006d)> at device 12.0 on pci0
found->	vendor=0x10b7, dev=0x9201, revid=0x40
	class=02-00-00, hdrtype=0x00, mfdev=0
	subordinatebus=0 	secondarybus=0
	intpin=a, irq=5
	map[10]: type 1, range 32, base 0000c000, size  7
	map[14]: type 1, range 32, base e7000000, size  7
pci2: <PCI bus> on pcib2
xl0: <3Com 3c920B-EMB Integrated Fast Etherlink XL> port 0xc000-0xc07f mem 
0xe7000000-0xe700007f irq 5 at device 1.0 on pci2
xl0: using port I/O
xl0: Ethernet address: 00:26:54:0a:df:a2
xl0: media options word: 40
xl0: found MII/AUTO
miibus0: <MII bus> on xl0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: OUI 0x000895, model 0x0012, rev. 1
ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: xl0 attached
	using shared irq5.
fwohci0: vendor=10de, dev=6e
fwohci0: <1394 Open Host Controller Interface> mem 
0xed085000-0xed08503f,0xed084000-0xed0847ff irq 11 at device 13.0 on pci0
fwohci0: latency timer 0 -> 32.
fwohci0: cache size 0 -> 8.
	using shared irq11.
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channel is 4.
fwohci0: EUI64 00:e0:18:00:00:16:af:0a
fwohci0: resetting OHCI...done (loop=0)
fwohci0: fwphy_rddata: 0x2 loop=1, retry=0
fwohci0: fwphy_rddata: 0x3 loop=1, retry=0
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: fwphy_rddata: 0x5 loop=1, retry=0
fwohci0: Enable 1394a Enhancements
fwohci0: fwphy_rddata: 0x5 loop=1, retry=0
fwohci0: fwphy_rddata: 0x2 loop=1, retry=0
fwohci0: fwphy_rddata: 0x4 loop=1, retry=0
fwohci0: fwphy_rddata: 0x4 loop=1, retry=0
fwohci0: fwphy_rddata: 0x4 loop=1, retry=0
fwohci0: Link S400, max_rec 2048 bytes.
fwohci0: BUS_OPT 0x601ca002 -> 0xf81ca002
fwohci0: fwohci_set_intr: 1
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:e0:18:16:af:0a
bpf: fwe0 attached
sbp0: <SBP-2/SCSI over FireWire> on firewire0
sbp_attach (cold=1)
sbp_post_busreset
fwohci0: Initiate bus reset
fwohci0: fwphy_rddata: 0x1 loop=1, retry=0
fwohci0: fwphy_rddata: 0x1 loop=1, retry=0
pcib3: <PCI to PCI bridge (vendor=10de device=01e8)> at device 30.0 on pci0
found->	vendor=0x102b, dev=0x0525, revid=0x85
	class=03-00-00, hdrtype=0x00, mfdev=0
	subordinatebus=0 	secondarybus=0
	intpin=a, irq=11
	map[10]: type 1, range 32, base e4000000, size 25
	map[14]: type 1, range 32, base e8000000, size 14
	map[18]: type 1, range 32, base e9000000, size 23
pci3: <PCI bus> on pcib3
pci3: <Matrox MGA G400 AGP graphics accelerator> (vendor=0x102b, dev=0x0525) 
at 0.0 irq 11
ex_isa_identify()
ata-: ata0 exists, using next available unit number
ata-: ata1 exists, using next available unit number
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem 0xc0000-0xc87ff,0xcc000-0xcd7ff,0xce000-0xce7ff 
on isa0
pmtimer0 on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
ata2 failed to probe at port 0x1f0 irq 14 on isa0
ata3 failed to probe at port 0x170 irq 15 on isa0
adv0 failed to probe on isa0
bt0: Failed Status Reg Test - fe
bt_isa_probe: Probe failed at 0x330
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x334
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x230
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x234
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x130
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x134
bt0 failed to probe at port 0x134-0x137 on isa0
aha0: status reg test failed fe
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0 failed to probe at port 0x134-0x137 on isa0
aic0 failed to probe at port 0x140-0x15f on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x1d0000
psm0: current command byte:0047
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
psm: status 00 02 64
psm: status 00 03 06
psm: status 00 33 55
psm: data 08 00 00
psm: status 00 02 64
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model NetMouse/NetScroll Optical, device ID 0-00, 3 buttons
psm0: config:00000000, flags:00000000, packet size:4
psm0: syncmask:08, syncbits:08
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
sio0: irq maps: 0x1 0x11 0x1 0x1
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: irq maps: 0x1 0x1 0x1 0x1
sio1: probe failed test(s): 0 1 2 4 6 7 9
sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
ppc0: parallel port found at 0x378
ppc0: using extended I/O port range
ppc0: EPP SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
bpf: lp0 attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
cs0: not probed (disabled)
sn0: not probed (disabled)
isa_probe_children: probing PnP devices
BIOS Geometries:
0:03fffe3f 0..1023=1024 cylinders, 0..254=255 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
bpf: lo0 attached
bpf: ppp0 attached
new masks: bio 68c868, tty 631092, net 6718b2
bpf: sl0 attached
bpf: faith0 attached
Linux ELF exec handler installed
ad0: success setting UDMA5 on nVIDIA chip
Creating DISK ad0
ar: FreeBSD check1 failed
ad0: <WDC WD800JB-00ETA0/77.07W77> ATA-6 disk at ata0-master
ad0: 76319MB (156301488 sectors), 155061 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA100
ad0: piomode=4 dmamode=2 udmamode=5 cblid=1
ad1: success setting UDMA5 on nVIDIA chip
Creating DISK ad1
ar: FreeBSD check1 failed
ad1: <WDC WD400BB-60BNA1/18.20D18> ATA-5 disk at ata0-slave
ad1: 38166MB (78165360 sectors), 77545 C, 16 H, 63 S, 512 B
ad1: 16 secs/int, 1 depth queue, UDMA100
ad1: piomode=4 dmamode=2 udmamode=5 cblid=1
[here it stops...]


Thanks for your time.

_________________________________________________________________
MSN 8 helps eliminate e-mail viruses. Get 2 months FREE*. 
http://join.msn.com/?page=features/virus



More information about the freebsd-stable mailing list