Booting of snapshot-iso on SUN Fire V280R

Wed Oct 29 07:02:11 PDT 2008

Hi Marius,

On Wed, Oct 29, 2008 at 09:15:58AM +0100, Marius Strobl wrote:

> I'm uploading a new one at:
> http://people.freebsd.org/~marius/8.0-20081028-SNAP-sparc64-disc1.iso.gz

Besides one LOR everything seems fine now, thanks a lot! :)

Sun Fire 280R (2 X UltraSPARC-III+) , No Keyboard
Copyright 1998-2004 Sun Microsystems, Inc.  All rights reserved.
OpenBoot 4.16.4, 8192 MB memory installed, Serial #53054758.
Ethernet address 0:3:ba:29:8d:26, Host ID: 83298d26.

Rebooting with command: boot cdrom                                    
Boot device: /pci at 8,700000/scsi at 6/disk at 6,0:f  File and args: 

>> FreeBSD/sparc64 boot block
   Boot path:   /pci at 8,700000/scsi at 6/disk at 6,0:f
   Boot loader: /boot/loader
Consoles: Open Firmware console  

Booting with sun4u support.
Boot path set to /pci at 8,700000/scsi at 6/disk at 6,0:a

FreeBSD/sparc64 bootstrap loader, Revision 1.0
(root at nimrod.franken.de, Wed Oct 29 00:11:36 UTC 2008)
bootpath="/pci at 8,700000/scsi at 6/disk at 6,0:a"
Loading /boot/defaults/loader.conf 
/boot/kernel/kernel data=0x813348+0x216928 syms=[0x8+0x91578+0x8+0x8387c]
-
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]...               
jumping to kernel entry at 0xc0080000.
GDB: no debug ports present
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1992-2008 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.0-20081028-SNAP #0: Wed Oct 29 02:22:05 UTC 2008
    root at nimrod.franken.de:/usr/obj/usr/src/sys/GENERIC
WARNING: WITNESS option enabled, expect reduced performance.
real memory  = 8589934592 (8192 MB)
avail memory = 8381685760 (7993 MB)
cpu0: Sun Microsystems UltraSparc-III+ Processor (900.00 MHz CPU)
cpu1: Sun Microsystems UltraSparc-III+ Processor (900.00 MHz CPU)
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
registered firmware set <isp_1000>
registered firmware set <isp_1040>
registered firmware set <isp_1040_it>
registered firmware set <isp_1080>
registered firmware set <isp_1080_it>
registered firmware set <isp_12160>
registered firmware set <isp_12160_it>
registered firmware set <isp_2100>
registered firmware set <isp_2200>
registered firmware set <isp_2300>
registered firmware set <isp_2322>
registered firmware set <isp_2400>
kbd0 at kbdmux0
ath_hal: 0.10.5.10 (AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2133, RF2425, RF2417, REGOPS_FUNC)
nexus0: <Open Firmware Nexus device>
nexus0: <memory-controller> mem 0x40000400000-0x40000400047 type memory-controller (no driver attached)
nexus0: <memory-controller> mem 0x40000c00000-0x40000c00047 type memory-controller (no driver attached)
pcib0: <Sun Host-PCI bridge> mem 0x40004700000-0x40004717fff,0x40004410000-0x4000441004f,0x7ffee000000-0x7ffee0000ff irq 563,560,561,564,550 on nexus0
pcib0: Schizo, version 5, IGN 0x8, bus B, 33MHz
pcib0: DVMA map: 0xc0000000 to 0xffffffff
pcib0: [FILTER]
pcib0: [FILTER]
pcib0: [FILTER]
pcib0: [FILTER]
pci0: <OFW PCI bus> on pcib0
ebus0: <PCI-EBus3 bridge> mem 0x7d000000-0x7dffffff,0x7e000000-0x7e7fffff at device 5.0 on pci0
ebus0: <flashprom> addr 0-0x1fffff (no driver attached)
ebus0: <i2c> addr 0x10000002e-0x10000002f,0x10000002d irq 35 (no driver attached)
ebus0: <bbc> addr 0x100000000-0x1000fffff (no driver attached)
ebus0: <power> addr 0x10030002e-0x10030002f,0x100300600-0x100300607 (no driver attached)
ebus0: <i2c> addr 0x100000030-0x100000031 irq 35 (no driver attached)
ebus0: <beep> addr 0x100000032-0x100000037 (no driver attached)
rtc0: <Real-Time Clock> addr 0x100300070-0x100300071 irq 36 on ebus0
ebus0: <gpio> addr 0x100300600-0x100300607 (no driver attached)
ebus0: <pmc> addr 0x100300700-0x100300701 (no driver attached)
ebus0: <parallel> addr 0x100300278-0x100300287,0x10030002e-0x10030002f,0x100700000-0x10070000f irq 28 (no driver attached)
uart0: <16550 or compatible> addr 0x1003062f8-0x1003062ff irq 46 on ebus0
uart0: [FILTER]
uart1: <16550 or compatible> addr 0x1003083f8-0x1003083ff irq 45 on ebus0
uart1: [FILTER]
uart1: console (115200,n,8,1)
scc0: <Siemens SAB 82532 dual channel SCC> addr 0x100400000-0x10040007f irq 34 on ebus0
scc0: [FILTER]
uart2: <SAB 82532 v3.2, channel A> on scc0
uart2: [FILTER]
uart2: CTS oflow
uart3: <SAB 82532 v3.2, channel B> on scc0
uart3: [FILTER]
uart3: CTS oflow
gem0: <Sun ERI 10/100 Ethernet> mem 0x100000-0x11ffff at device 5.1 on pci0
miibus0: <MII bus> on gem0
ukphy0: <Generic IEEE 802.3u media interface> PHY 1 on miibus0
ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
gem0: 2kB RX FIFO, 2kB TX FIFO
gem0: Ethernet address: 00:03:ba:29:8d:26
gem0: [ITHREAD]
ohci0: <Sun PCIO-2 USB controller> mem 0x1000000-0x1007fff at device 5.3 on pci0
ohci0: [GIANT-LOCKED]
ohci0: [ITHREAD]
usb0: OHCI version 1.0, legacy support
usb0: <Sun PCIO-2 USB controller> on ohci0
usb0: USB revision 1.0
uhub0: <(0x108e) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 4 ports with 4 removable, self powered
sym0: <875> port 0x300-0x3ff mem 0x124000-0x1240ff,0x126000-0x126fff at device 6.0 on pci0
sym0: No NVRAM, ID 7, Fast-20, SE, parity checking
sym0: [ITHREAD]
sym1: <875> port 0x400-0x4ff mem 0x128000-0x1280ff,0x12a000-0x12afff at device 6.1 on pci0
sym1: No NVRAM, ID 7, Fast-20, SE, parity checking
sym1: [ITHREAD]
pcib1: <OFW PCI-PCI bridge> at device 3.0 on pci0
pci1: <OFW PCI bus> on pcib1
pci1: <bridge> at device 0.0 (no driver attached)
hme0: <Sun HME 10/100 Ethernet> mem 0x3800000-0x3807fff at device 0.1 on pci1
miibus1: <MII bus> on hme0
ukphy1: <Generic IEEE 802.3u media interface> PHY 1 on miibus1
ukphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
hme0: Ethernet address: 00:03:ba:1f:72:39
hme0: [ITHREAD]
pci1: <bridge> at device 1.0 (no driver attached)
hme1: <Sun HME 10/100 Ethernet> mem 0x3808000-0x380ffff at device 1.1 on pci1
miibus2: <MII bus> on hme1
ukphy2: <Generic IEEE 802.3u media interface> PHY 1 on miibus2
ukphy2:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
hme1: Ethernet address: 00:03:ba:1f:72:3a
hme1: [ITHREAD]
pci1: <bridge> at device 2.0 (no driver attached)
hme2: <Sun HME 10/100 Ethernet> mem 0x3810000-0x3817fff at device 2.1 on pci1
miibus3: <MII bus> on hme2
ukphy3: <Generic IEEE 802.3u media interface> PHY 1 on miibus3
ukphy3:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
hme2: Ethernet address: 00:03:ba:1f:72:3b
hme2: [ITHREAD]
pci1: <bridge> at device 3.0 (no driver attached)
hme3: <Sun HME 10/100 Ethernet> mem 0x3818000-0x381ffff at device 3.1 on pci1
miibus4: <MII bus> on hme3
ukphy4: <Generic IEEE 802.3u media interface> PHY 1 on miibus4
ukphy4:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
hme3: Ethernet address: 00:03:ba:1f:72:3c
hme3: [ITHREAD]
pcib2: <Sun Host-PCI bridge> mem 0x40004600000-0x40004617fff,0x40004410000-0x4000441004f,0x7ffec000000-0x7ffec0000ff irq 562,560,561,564 on nexus0
pcib2: Schizo, version 5, IGN 0x8, bus A, 66MHz
Timecounter "pcib2" frequency 150000000 Hz quality 100
pcib2: DVMA map: 0xc0000000 to 0xffffffff
pcib2: [FILTER]
pci2: <OFW PCI bus> on pcib2
isp0: <Qlogic ISP 2200 PCI FC-AL Adapter> port 0x300-0x3ff mem 0x100000-0x100fff at device 4.0 on pci2
isp0: [ITHREAD]
isp0: Board Type 2200, Chip Revision 0x5, loaded F/W Revision 2.2.6
isp0: invalid NVRAM header
isp0: invalid NVRAM header
nexus0: <syscons> type unknown (no driver attached)
Timecounter "tick" frequency 900000000 Hz quality 10
Timecounters tick every 1.000 msec
Waiting 5 seconds for SCSI devices to settle
md0: Preloaded image </boot/mfsroot> 4194304 bytes at 0xc0b3ea78
da0 at isp0 bus 0 target 0 lun 0
da0: <SEAGATE ST373405FSUN72G 0438> Fixed Direct Access SCSI-3 device 
da0: 100.000MB/s transfers
da0: Command Queueing Enabled
da0: 70007MB (143374738 512 byte sectors: 255H 63S/T 8924C)
da1 at isp0 bus 0 target 1 lun 0
da1: <SEAGATE ST373405FSUN72G 0438> Fixed Direct Access SCSI-3 device 
da1: 100.000MB/s transfers WWNN 0x20000004cfa12ee6 WWPN 0x21000004cfa12ee6 PortID 0xe8
da1: Command Queueing Enabled
da1: 70007MB (143374738 512 byte sectors: 255H 63S/T 8924C)
SMP: AP CPU #1 Launched!
WARNING: WITNESS option enabled, expect reduced performance.
cd0 at sym0 bus 0 target 6 lun 0
cd0: <TOSHIBA DVD-ROM SD-M1401 1009> Removable CD-ROM SCSI-2 device 
cd0: 3.300MB/s transfers
cd0: cd present [979800 x 512 byte records]
GEOM_LABEL: Label for provider cd0 is iso9660/FreeBSD_Install.
Trying to mount root from ufs:/dev/md0
lock order reversal:
 1st 0xfffff8000309e070 user map (user map) @ /usr/src/sys/vm/vm_map.c:3115
 2nd 0xfffff800035c94e0 ufs (ufs) @ /usr/src/sys/kern/vfs_subr.c:2046
KDB: stack backtrace:
_witness_debugger() at _witness_debugger+0x38
witness_checkorder() at witness_checkorder+0xcf8
__lockmgr_args() at __lockmgr_args+0x2d0
ffs_lock() at ffs_lock+0x88
VOP_LOCK1_APV() at VOP_LOCK1_APV+0x110
_vn_lock() at _vn_lock+0x80
vget() at vget+0x120
vnode_pager_lock() at vnode_pager_lock+0x240
vm_fault() at vm_fault+0x208
trap_pfault() at trap_pfault+0x198
trap() at trap+0xd0
-- fast data access mmu miss tar=0x476001 %o7=0xc0081208 --
userland() at 0x10015c
user trace: trap %o7=0xc0081208
pc 0x10015c, sp 0x7fdffffe531
pc 0, sp 0x7fdffffe5f1
done
/stand/sysinstall running as init on serial console

Kind Regards
-- 
Michael Moll
e-mail : kvedulv at kvedulv.de
  WWW  : http://www.kvedulv.de/
  GSM  : +49 175 606 7861