E450 panic - SNAP 20030423 5.0-Current

[Brian Denehy]

Hi folks,


I'm trying to use sparc64 for the first time - any ideas on this problem? 
The CURRENT hardware release notes suggest it should boot.



{1} ok boot cdrom
Resetting ...


Can't open input device.
screen not found.
Can't open input device.
Keyboard not present.  Using ttya for input and output.
Keyboard not present.  Using ttya for input and output.


Sun Enterprise 450 (2 X UltraSPARC-II 400MHz), No Keyboard
OpenBoot 3.22, 1024 MB memory installed, Serial #12868830.
Ethernet address 8:0:20:c4:5c:de, Host ID: 80c45cde.



Rebooting with command: boot cdrom
Boot device: /pci at 1f,4000/scsi at 2/disk at 6,0:f  File and args:

>> FreeBSD/sparc64 boot block
   Boot path:   /pci at 1f,4000/scsi at 2/disk at 6,0:f
   Boot loader: /boot/loader
Console: OpenFirmware console
Boot path set to /pci at 1f,4000/scsi at 2/disk at 6,0:a

FreeBSD/sparc64 bootstrap loader, Revision 1.0
(jake at u10.locore.ca, Tue Apr 22 13:21:52 EDT 2003)
bootpath="/pci at 1f,4000/scsi at 2/disk at 6,0:a"
Loading /boot/defaults/loader.conf
/boot/kernel/kernel data=0x384708+0x126f28 syms=[0x8+0x503a0+0x8+0x3f836]
|
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]...
nothing to autoload yet.
jumping to kernel entry at 0xc0040000.
Copystray vector interrupt 2029
right (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 5.0-20030423-SNAP #0: Thu Apr 24 07:06:16 GMT 2003
    root at u10.locore.ca:/usr/obj/usr/src/sys/GENERIC
Preloaded elf kernel "/boot/kernel/kernel" at 0xc093e000.
Preloaded mfs_root "/boot/mfsroot" at 0xc093e190.
Timecounter "tick"  frequency 400000000 Hz
real memory  = 1042874368 (994 MB)
avail memory = 1014259712 (967 MB)
cpu0: Sun Microsystems UltraSparc-II Processor (400.00 MHz CPU)
cpu1: Sun Microsystems UltraSparc-II Processor (400.00 MHz CPU)
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
md0: Preloaded image </boot/mfsroot> 4194304 bytes at 0xc053b218
nexus0: <OpenFirmware Nexus device>
nexus0: <associations>, type (unknown) (no driver attached)
pcib0: <U2P UPA-PCI bridge> on nexus0
pcib0: Psycho, impl 0, version 4, ign 0x7c0
initialializing counter-timer
Timecounter "counter-timer"  frequency 1000000 Hz
DVMA map: 0xfe000000 to 0xffffffff
device 0/1/0: latency timer 10 -> 82
pcib0: ofw_pci_init: no interrupt mapping found for 0/1/0 (preset 0)
device 0/1/1: latency timer 10 -> 82
pcib0: ofw_pci_init: mapping intr for 0/1/1 to 33 (preset was 0)
device 0/3/0: latency timer 17 -> 140
pcib0: ofw_pci_init: mapping intr for 0/3/0 to 32 (preset was 0)
device 0/2/0: latency timer 17 -> 140
pcib0: ofw_pci_init: mapping intr for 0/2/0 to 38 (preset was 0)
pci0: <PCI bus> on pcib0
ebus0: revision 0x01
ebus0: <PCI-EBus2 bridge> mem 0x71000000-0x717fffff,0x70000000-0x70ffffff 
at devic
e 1.0 on pci0
ebus0: <auxio> addr 
0x140072f000-0x140072f003,0x140072c000-0x140072c003,0x140072a0
00-0x140072a003,0x1400728000-0x1400728003,0x1400726000-0x1400726003 (no 
driver att
ached)
ebus0: <power> addr 0x1400724000-0x1400724003 irq 2034,2021 (no driver 
attached)
ebus0: <SUNW,pll> addr 0x1400504000-0x1400504002 (no driver attached)
ebus0: <sc> addr 0x1400500000-0x1400500007 (no driver attached)
sab0: <Siemens SAB 82532 v3.2> addr 0x1400400000-0x140040007f irq 43 on 
ebus0
sabtty0: <ttya> on sab0
sabtty0: console 9600,8,n,1,-
sabtty1: <ttyb> on sab0
ebus0: <su> addr 0x14003083f8-0x14003083ff irq 41 (no driver attached)
ebus0: <su> addr 0x14003062f8-0x14003062ff irq 42 (no driver attached)
ebus0: <ecpp> addr 
0x1400700000-0x140070000f,0x1400300398-0x1400300399,0x14003043b
c-0x14003043cb irq 2018 (no driver attached)
ebus0: <fdthree> addr 
0x1400720000-0x1400720003,0x1400706000-0x140070600f,0x140030
23f0-0x14003023f7 irq 2023 (no driver attached)
eeprom0: <EBus EEPROM/clock> addr 0x1400000000-0x1400001fff on ebus0
eeprom0: model mk48t59
eeprom0: hostid 80c45cde
ebus0: <flashprom> addr 
0x1000000000-0x10000fffff,0x1000000000-0x10000fffff (no dr
iver attached)
ebus0: <SUNW,envctrl> addr 0x1400600000-0x1400600003 irq 2021,2024 (no 
driver atta
ched)
hme0: <Sun HME 10/100 Ethernet> mem 0x8000-0xffff irq 33 at device 1.1 on 
pci0
hme0: Ethernet address: 08:00:20:c4:5c:de
miibus0: <MII bus> on hme0
nsphy0: <DP83840 10/100 media interface> on miibus0
nsphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sym0: <875> port 0x800-0x8ff mem 0x16000-0x16fff,0x14000-0x140ff irq 38 at 
device
2.0 on pci0
sym0: No NVRAM, ID 7, Fast-20, SE, parity checking
sym1: <875> port 0x400-0x4ff mem 0x12000-0x12fff,0x10000-0x100ff irq 32 at 
device
3.0 on pci0
sym1: No NVRAM, ID 7, Fast-20, SE, parity checking
pcib1: <U2P UPA-PCI bridge> on nexus0
pcib1: Psycho, impl 0, version 4, ign 0x7c0
pci1: <PCI bus> on pcib1
nexus0: <mc>, type memory-controller (no driver attached)
pcib2: <U2P UPA-PCI bridge> on nexus0
pcib2: Psycho, impl 0, version 4, ign 0x100
initialializing counter-timer
Timecounter "counter-timer"  frequency 1000000 Hz
DVMA map: 0xfe000000 to 0xffffffff
pci2: <PCI bus> on pcib2
pcib3: <U2P UPA-PCI bridge> on nexus0
pcib3: Psycho, impl 0, version 4, ign 0x100
device 3/1/0: latency timer 17 -> 140
pcib3: ofw_pci_init: mapping intr for 3/1/0 to 1 (preset was 0)
device 3/1/1: latency timer 17 -> 140
pcib3: ofw_pci_init: mapping intr for 3/1/1 to 2 (preset was 0)
pci3: <PCI bus> on pcib3
sym2: <875> port 0x1000-0x10ff mem 
0x10102000-0x10102fff,0x10100000-0x101000ff irq
 1 at device 1.0 on pci3
sym2: No NVRAM, ID 7, Fast-20, SE, parity checking
sym3: <875> port 0x1400-0x14ff mem 
0x10106000-0x10106fff,0x10104000-0x101040ff irq
 2 at device 1.1 on pci3
sym3: No NVRAM, ID 7, Fast-20, SE, parity checking
pcib4: <U2P UPA-PCI bridge> on nexus0
pcib4: Psycho, impl 0, version 4, ign 0x180
initialializing counter-timer
Timecounter "counter-timer"  frequency 1000000 Hz
DVMA map: 0xfe000000 to 0xffffffff
PCI-PCI bridge at 4/3/0: setting bus #s to 4/5/5
pcib4: ofw_pci_init: descending to subordinate PCI bus
device 5/0/0: latency timer 10 -> 82
pcib4: ofw_pci_init: mapping intr for 5/0/0 to 1 (preset was 0)
device 5/0/1: latency timer 10 -> 82
pcib4: ofw_pci_init: mapping intr for 5/0/1 to 2 (preset was 0)
device 5/1/0: latency timer 10 -> 82
pcib4: ofw_pci_init: mapping intr for 5/1/0 to 1 (preset was 0)
device 5/1/1: latency timer 10 -> 82
pcib4: ofw_pci_init: mapping intr for 5/1/1 to 2 (preset was 0)
device 5/2/0: latency timer 10 -> 82
pcib4: ofw_pci_init: mapping intr for 5/2/0 to 1 (preset was 0)
device 5/2/1: latency timer 10 -> 82
pcib4: ofw_pci_init: mapping intr for 5/2/1 to 2 (preset was 0)
device 5/3/0: latency timer 10 -> 82
pcib4: ofw_pci_init: mapping intr for 5/3/0 to 1 (preset was 0)
device 5/3/1: latency timer 10 -> 82
pcib4: ofw_pci_init: mapping intr for 5/3/1 to 2 (preset was 0)
device 4/4/0: latency timer 17 -> 140
pcib4: ofw_pci_init: mapping intr for 4/4/0 to 1 (preset was 0)
device 4/4/1: latency timer 17 -> 140
pcib4: ofw_pci_init: mapping intr for 4/4/1 to 2 (preset was 0)
pci4: <PCI bus> on pcib4
pcib5: <PCI-PCI bridge> at device 3.0 on pci4
pci5: <PCI bus> on pcib5
pci5: <bridge, PCI-unknown> at device 0.0 (no driver attached)
hme1: <Sun HME 10/100 Ethernet> mem 0x4000000-0x4007fff irq 2 at device 
0.1 on pci
5
hme1: Ethernet address: 08:00:20:c4:5c:de
miibus1: <MII bus> on hme1
qsphy0: <QS6612 10/100 media interface> on miibus1
qsphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci5: <bridge, PCI-unknown> at device 1.0 (no driver attached)
hme2: <Sun HME 10/100 Ethernet> mem 0x8000000-0x8007fff irq 2 at device 
1.1 on pci
5
hme2: Ethernet address: 08:00:20:c4:5c:de
miibus2: <MII bus> on hme2
qsphy1: <QS6612 10/100 media interface> on miibus2
qsphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci5: <bridge, PCI-unknown> at device 2.0 (no driver attached)
hme3: <Sun HME 10/100 Ethernet> mem 0xc000000-0xc007fff irq 2 at device 
2.1 on pci
5
hme3: Ethernet address: 08:00:20:c4:5c:de
miibus3: <MII bus> on hme3
qsphy2: <QS6612 10/100 media interface> on miibus3
qsphy2:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci5: <bridge, PCI-unknown> at device 3.0 (no driver attached)
hme4: <Sun HME 10/100 Ethernet> mem 0x10000000-0x10007fff irq 2 at device 
3.1 on p
ci5
hme4: Ethernet address: 08:00:20:c4:5c:de
miibus4: <MII bus> on hme4
qsphy3: <QS6612 10/100 media interface> on miibus4
qsphy3:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sym4: <875> port 0x1000-0x10ff mem 
0x10102000-0x10102fff,0x10100000-0x101000ff irq
 1 at device 4.0 on pci4
sym4: No NVRAM, ID 7, Fast-20, SE, parity checking
sym5: <875> port 0x1400-0x14ff mem 
0x10106000-0x10106fff,0x10104000-0x101040ff irq
 2 at device 4.1 on pci4
sym5: No NVRAM, ID 7, Fast-20, SE, parity checking
pcib6: <U2P UPA-PCI bridge> on nexus0
pcib6: Psycho, impl 0, version 4, ign 0x180
pci6: <PCI bus> on pcib6
Timecounters tick every 10.000 msec
Waiting 15 seconds for SCSI devices to settle
panic: trap: memory address not aligned
cpuid = 0;
Debugger("panic")
Stopped at      Debugger+0x1c:  ta              %xcc, 1
db> trace
panic() at panic+0x134
trap() at trap+0x3a4
-- memory address not aligned sfar=0xdedeadc0de sfsr=0x40029 
%o7=0xc0282fd0 --
iommu_dvmamap_vunload() at iommu_dvmamap_vunload+0x14
iommu_dvma_vfree() at iommu_dvma_vfree+0x48
iommu_dvmamap_destroy() at iommu_dvmamap_destroy+0x8
psycho_dmamap_destroy() at psycho_dmamap_destroy+0x14
___dma_getp() at ___dma_getp+0x1b0
___sym_malloc() at ___sym_malloc+0x70
__sym_calloc2() at __sym_calloc2+0xc
__sym_calloc_dma() at __sym_calloc_dma+0x64
sym_alloc_ccb() at sym_alloc_ccb+0x24
sym_get_ccb() at sym_get_ccb+0x68
sym_action1() at sym_action1+0x154
sym_action() at sym_action+0x8
xpt_run_dev_sendq() at xpt_run_dev_sendq+0x208
xpt_release_devq_device() at xpt_release_devq_device+0xd8
xpt_release_devq_timeout() at xpt_release_devq_timeout+0xc
softclock() at softclock+0x190
ithread_loop() at ithread_loop+0x240
fork_exit() at fork_exit+0xd8
fork_trampoline() at fork_trampoline+0xdc
db>


All feedback gratefully accepted



Brian Denehy