SMP kernel but no SMP detected on Tyan S2515
Mark Kirkwood
markir at paradise.net.nz
Tue Nov 15 23:17:07 PST 2005
This has me puzzled:
I have a 2 cpu S2515 that has had SMP added to the kernel - however upon
reboot the 2nd cpu is not detected (It is detected by the BIOS BTW). I
see the following in the verbose dmesg:
APIC: Could not find any APICs.
I am guessing that it is turned off in the BIOS (???), if so, I've no
idea where it is (AMIBIOS is my least favorite...).
I have enclosed a verbose dmesg and my kernel differences from GENERIC
plus the (non-existent) output from mptable.
Any ideas appreciated.
regards
Mark
-------------- next part --------------
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 6.0-RELEASE #0: Wed Nov 16 19:09:19 NZDT 2005
root at ikker.markir.net:/usr/obj/usr/src/sys/STANDARD
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0a42000.
Calibrating clock(s) ... i8254 clock: 1192994 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 996845270 Hz
CPU: Intel Pentium III (996.85-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x68a Stepping = 10
Features=0x387fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,PN,MMX,FXSR,SSE>
real memory = 2147483648 (2048 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000c28000 - 0x000000007dbc7fff, 2096758784 bytes (511904 pages)
avail memory = 2096533504 (1999 MB)
APIC: Could not find any APICs.
bios32: Found BIOS32 Service Directory header at 0xc00fdb90
bios32: Entry = 0xfdba0 (c00fdba0) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0xdbc1
pnpbios: Found PnP BIOS data at 0xc00f4320
pnpbios: Entry = f0000:2fa4 Rev = 1.0
Other BIOS signatures found:
wlan: <802.11 Link Layer>
null: <null device, zero device>
random: <entropy source, Software, Yarrow>
nfslock: pseudo-device
io: <I/O>
mem: <memory>
Pentium Pro MTRR support enabled
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
cpu0 on motherboard
pci_open(1): mode 1 addr port (0x0cf8) is 0x80000070
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=80] is there (id=00091166)
pcibios: BIOS version 2.10
Found $PIR table, 10 entries at 0xc00f4b30
PCI-Only Interrupts: none
Location Bus Device Pin Link IRQs
embedded 0 15 A 0x01 10
embedded 0 4 A 0x14 3 4 5 7 9 10 11 12 14 15
embedded 0 5 A 0x15 3 4 5 7 9 10 11 12 14 15
embedded 0 1 A 0x16 3 4 5 7 9 10 11 12 14 15
embedded 0 3 A 0x1f 3 4 5 7 9 10 11 12 14 15
embedded 1 6 A 0x1d 3 4 5 7 9 10 11 12 14 15
embedded 1 6 B 0x1c 3 4 5 7 9 10 11 12 14 15
slot 1 1 2 A 0x1b 3 4 5 7 9 10 11 12 14 15
slot 1 1 2 B 0x1e 3 4 5 7 9 10 11 12 14 15
slot 1 1 2 C 0x1d 3 4 5 7 9 10 11 12 14 15
slot 1 1 2 D 0x1c 3 4 5 7 9 10 11 12 14 15
slot 2 1 3 A 0x17 3 4 5 7 9 10 11 12 14 15
slot 2 1 3 B 0x18 3 4 5 7 9 10 11 12 14 15
slot 2 1 3 C 0x19 3 4 5 7 9 10 11 12 14 15
slot 2 1 3 D 0x1a 3 4 5 7 9 10 11 12 14 15
slot 3 1 4 A 0x1e 3 4 5 7 9 10 11 12 14 15
slot 3 1 4 B 0x1d 3 4 5 7 9 10 11 12 14 15
slot 3 1 4 C 0x1c 3 4 5 7 9 10 11 12 14 15
slot 3 1 4 D 0x1b 3 4 5 7 9 10 11 12 14 15
slot 4 1 5 A 0x1d 3 4 5 7 9 10 11 12 14 15
slot 4 1 5 B 0x1c 3 4 5 7 9 10 11 12 14 15
slot 4 1 5 C 0x1b 3 4 5 7 9 10 11 12 14 15
slot 4 1 5 D 0x1e 3 4 5 7 9 10 11 12 14 15
pcib0: <ServerWorks NB6635 3.0LE host to PCI bridge> pcibus 0 on motherboard
pir0: <PCI Interrupt Routing Table: 10 Entries> on motherboard
$PIR: Links after initial probe:
Link IRQ Rtd Ref IRQs
0x1 255 N 1 10
0x14 255 N 1 3 4 5 7 9 10 11 12 14 15
0x15 255 N 1 3 4 5 7 9 10 11 12 14 15
0x16 255 N 1 3 4 5 7 9 10 11 12 14 15
0x1f 255 N 1 3 4 5 7 9 10 11 12 14 15
0x1d 255 N 4 3 4 5 7 9 10 11 12 14 15
0x1c 255 N 4 3 4 5 7 9 10 11 12 14 15
0x1b 255 N 3 3 4 5 7 9 10 11 12 14 15
0x1e 255 N 3 3 4 5 7 9 10 11 12 14 15
0x17 255 N 1 3 4 5 7 9 10 11 12 14 15
0x18 255 N 1 3 4 5 7 9 10 11 12 14 15
0x19 255 N 1 3 4 5 7 9 10 11 12 14 15
0x1a 255 N 1 3 4 5 7 9 10 11 12 14 15
$PIR: Found matching pin for 0.15.INTA at func 2: 10
$PIR: Found matching pin for 0.4.INTA at func 0: 9
$PIR: Found matching pin for 0.5.INTA at func 0: 5
$PIR: Found matching pin for 0.1.INTA at func 0: 11
$PIR: Found matching pin for 1.2.INTA at func 0: 10
$PIR: Links after initial IRQ discovery:
Link IRQ Rtd Ref IRQs
0x1 10 N 1 10
0x14 9 Y 1 3 4 5 7 9 10 11 12 14 15
0x15 5 Y 1 3 4 5 7 9 10 11 12 14 15
0x16 11 Y 1 3 4 5 7 9 10 11 12 14 15
0x1f 255 N 1 3 4 5 7 9 10 11 12 14 15
0x1d 255 N 4 3 4 5 7 9 10 11 12 14 15
0x1c 255 N 4 3 4 5 7 9 10 11 12 14 15
0x1b 10 Y 3 3 4 5 7 9 10 11 12 14 15
0x1e 255 N 3 3 4 5 7 9 10 11 12 14 15
0x17 255 N 1 3 4 5 7 9 10 11 12 14 15
0x18 255 N 1 3 4 5 7 9 10 11 12 14 15
0x19 255 N 1 3 4 5 7 9 10 11 12 14 15
0x1a 255 N 1 3 4 5 7 9 10 11 12 14 15
$PIR: IRQs used by BIOS: 5 9 10 11
$PIR: Interrupt Weights:
[ 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 ]
[ 0 0 0 0 0 1 0 0 0 1 4 1 0 0 0 0 ]
pci0: <PCI bus> on pcib0
pci0: physical bus=0
found-> vendor=0x1166, dev=0x0009, revid=0x06
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0006, statreg=0x2200, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1166, dev=0x0009, revid=0x06
bus=0, slot=0, func=1
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x0200, cachelnsz=8 (dwords)
lattimer=0x10 (480 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1002, dev=0x4752, revid=0x27
bus=0, slot=1, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0087, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base fc000000, size 24, enabled
map[14]: type 4, range 32, base 0000d800, size 8, enabled
map[18]: type 1, range 32, base fdaff000, size 12, enabled
$PIR: 0:1 INTA routed to irq 11
found-> vendor=0x8086, dev=0x1229, revid=0x08
bus=0, slot=4, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0117, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x38 (14000 ns)
intpin=a, irq=9
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base fdafe000, size 12, enabled
map[14]: type 4, range 32, base 0000d400, size 6, enabled
map[18]: type 1, range 32, base fd900000, size 20, enabled
$PIR: 0:4 INTA routed to irq 9
found-> vendor=0x8086, dev=0x1229, revid=0x08
bus=0, slot=5, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0117, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x38 (14000 ns)
intpin=a, irq=5
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base fdafd000, size 12, enabled
map[14]: type 4, range 32, base 0000d000, size 6, enabled
map[18]: type 1, range 32, base fd700000, size 20, enabled
$PIR: 0:5 INTA routed to irq 5
found-> vendor=0x1166, dev=0x0200, revid=0x50
bus=0, slot=15, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[90]: type 4, range 32, base 00000580, size 4, enabled
found-> vendor=0x1166, dev=0x0211, revid=0x00
bus=0, slot=15, func=1
class=01-01-8a, hdrtype=0x00, mfdev=1
cmdreg=0x0005, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[20]: type 4, range 32, base 0000ffa0, size 4, enabled
found-> vendor=0x1166, dev=0x0220, revid=0x04
bus=0, slot=15, func=2
class=0c-03-10, hdrtype=0x00, mfdev=1
cmdreg=0x0117, statreg=0x0280, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x50 (20000 ns)
intpin=a, irq=10
map[10]: type 1, range 32, base fdafc000, size 12, enabled
$PIR: 0:15 INTA routed to irq 10
pci0: <display, VGA> at device 1.0 (no driver attached)
fxp0: <Intel 82559 Pro/100 Ethernet> port 0xd400-0xd43f mem 0xfdafe000-0xfdafefff,0xfd900000-0xfd9fffff irq 9 at device 4.0 on pci0
fxp0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfdafe000
fxp0: using memory space register mapping
fxp0: PCI IDs: 8086 1229 8086 000c 0008
fxp0: Dynamic Standby mode is disabled
miibus0: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: bpf attached
fxp0: Ethernet address: 00:e0:81:03:55:e2
fxp0: [MPSAFE]
fxp1: <Intel 82559 Pro/100 Ethernet> port 0xd000-0xd03f mem 0xfdafd000-0xfdafdfff,0xfd700000-0xfd7fffff irq 5 at device 5.0 on pci0
fxp1: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfdafd000
fxp1: using memory space register mapping
fxp1: PCI IDs: 8086 1229 8086 000c 0008
fxp1: Dynamic Standby mode is disabled
miibus1: <MII bus> on fxp1
inphy1: <i82555 10/100 media interface> on miibus1
inphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp1: bpf attached
fxp1: Ethernet address: 00:e0:81:03:55:e3
fxp1: [MPSAFE]
isab0: <PCI-ISA bridge> port 0x580-0x58f at device 15.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <ServerWorks ROSB4 UDMA33 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 15.1 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xffa0
ata0: <ATA channel 0> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=60 ostat1=70
ata0: stat0=0x20 err=0x20 lsb=0x20 msb=0x20
ata0: stat1=0x30 err=0x30 lsb=0x30 msb=0x30
ata0: reset tp2 stat0=20 stat1=30 devices=0x0
ata0: [MPSAFE]
ata1: <ATA channel 1> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=03 ostat0=50 ostat1=00
ata1: stat0=0x90 err=0x01 lsb=0x14 msb=0xeb
ata1: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: stat1=0x00 err=0x01 lsb=0x7f msb=0x7f
ata1: reset tp2 stat0=00 stat1=00 devices=0x4<ATAPI_MASTER>
ata1: [MPSAFE]
ohci0: <OHCI (generic) USB controller> mem 0xfdafc000-0xfdafcfff irq 10 at device 15.2 on pci0
ohci0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfdafc000
ohci0: (New OHCI DeviceId=0x02201166)
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pcib1: <ServerWorks NB6635 3.0LE host to PCI bridge> pcibus 1 on motherboard
pir: pir0 already exists; skipping it
pci1: <PCI bus> on pcib1
pci1: physical bus=1
found-> vendor=0x13c1, dev=0x1001, revid=0x01
bus=1, slot=2, func=0
class=01-04-00, hdrtype=0x00, mfdev=0
cmdreg=0x011f, statreg=0x02b0, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x09 (2250 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
powerspec 1 supports D0 D1 D3 current D0
map[10]: type 4, range 32, base 0000e800, size 4, enabled
map[18]: type 1, range 32, base fe000000, size 23, enabled
$PIR: 1:2 INTA routed to irq 10
twe0: <3ware Storage Controller. Driver version 1.50.01.002> port 0xe800-0xe80f mem 0xfe000000-0xfe7fffff irq 10 at device 2.0 on pci1
twe0: Reserved 0x10 bytes for rid 0x10 type 4 at 0xe800
twe0: [GIANT-LOCKED]
twe0: AEN: <soft reset>
twe0: 4 ports, Firmware FE7X 1.05.00.068, BIOS BE7X 1.08.00.048
twe0: Monitor ME7X 1.01.00.040, PCB Rev4 , Achip 3.20 , Pchip 1.30-66
twe0: port 2: ST320011A 19092MB
twe0: port 3: ST320011A 19092MB
ex_isa_identify()
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
pnpbios: 13 devices, largest 234 bytes
PNP0c01: adding fixed memory32 range 0-0x9fbff, size=0x9fc00
PNP0c01: adding fixed memory32 range 0x9fc00-0x9ffff, size=0x400
PNP0c01: adding fixed memory32 range 0xe0000-0xfffff, size=0x20000
PNP0c01: adding fixed memory32 range 0x100000-0x7fffffff, size=0x7ff00000
PNP0c01: adding fixed memory32 range 0xfec00000-0xfec00fff, size=0x1000
PNP0c01: adding fixed memory32 range 0xfec01000-0xfec01fff, size=0x1000
PNP0c01: adding fixed memory32 range 0xfee00000-0xfee00fff, size=0x1000
PNP0c01: adding fixed memory32 range 0xfff80000-0xffffffff, size=0x80000
pnpbios: handle 0 device ID PNP0c01 (010cd041)
PNP0200: adding dma mask 0x10
PNP0200: adding io range 0-0xf, size=0x10, align=0x1
PNP0200: adding io range 0x80-0x90, size=0x11, align=0x1
PNP0200: adding io range 0x94-0x9f, size=0xc, align=0x1
PNP0200: adding io range 0xc0-0xde, size=0x1f, align=0x1
pnpbios: handle 2 device ID PNP0200 (0002d041)
PNP0100: adding irq mask 0x1
PNP0100: adding io range 0x40-0x43, size=0x4, align=0x1
pnpbios: handle 3 device ID PNP0100 (0001d041)
PNP0b00: adding irq mask 0x100
PNP0b00: adding io range 0x70-0x71, size=0x2, align=0x1
pnpbios: handle 4 device ID PNP0b00 (000bd041)
PNP0303: adding irq mask 0x2
PNP0303: adding io range 0x60-0x60, size=0x1, align=0x1
PNP0303: adding io range 0x64-0x64, size=0x1, align=0x1
pnpbios: handle 5 device ID PNP0303 (0303d041)
PNP0800: adding io range 0x61-0x61, size=0x1, align=0x1
pnpbios: handle 6 device ID PNP0800 (0008d041)
PNP0c04: adding irq mask 0x2000
PNP0c04: adding io range 0xf0-0xff, size=0x10, align=0x1
pnpbios: handle 7 device ID PNP0c04 (040cd041)
PNP0c02: adding io range 0x4d0-0x4d1, size=0x2, align=0x1
PNP0c02: adding io range 0xcf8-0xcff, size=0x8, align=0x1
PNP0c02: adding io range 0x10-0x1f, size=0x10, align=0x1
PNP0c02: adding io range 0x40b-0x40b, size=0x1, align=0x1
PNP0c02: adding io range 0x4d6-0x4d6, size=0x1, align=0x1
PNP0c02: adding io range 0xc00-0xc01, size=0x2, align=0x1
PNP0c02: adding io range 0xc14-0xc14, size=0x1, align=0x1
PNP0c02: adding io range 0xc49-0xc4a, size=0x2, align=0x1
PNP0c02: adding io range 0xc52-0xc52, size=0x1, align=0x1
PNP0c02: adding io range 0xc6c-0xc6c, size=0x1, align=0x1
PNP0c02: adding io range 0xc6f-0xc6f, size=0x1, align=0x1
PNP0c02: adding io range 0xcd6-0xcd7, size=0x2, align=0x1
PNP0c02: adding io range 0xf50-0xf58, size=0x9, align=0x1
PNP0c02: adding io range 0x374-0x375, size=0x2, align=0x1
PNP0c02: adding io range 0x377-0x377, size=0x1, align=0x1
PNP0c02: adding fixed memory32 range 0xc9000-0xc97ff, size=0x800
PNP0c02: adding fixed memory32 range 0xcb800-0xd7fff, size=0xc800
pnpbios: handle 8 device ID PNP0c02 (020cd041)
PNP0c02: adding io range 0x580-0x58f, size=0x10, align=0x1
PNP0c02: adding io range 0x500-0x51f, size=0x20, align=0x1
pnpbios: handle 9 device ID PNP0c02 (020cd041)
pnpbios: handle 10 device ID PNP0a03 (030ad041)
PNP0501: adding io range 0x3f8-0x3ff, size=0x8, align=0x8
PNP0501: adding irq mask 0x10
pnpbios: handle 11 device ID PNP0501 (0105d041)
PNP0501: adding io range 0x2f8-0x2ff, size=0x8, align=0x8
PNP0501: adding irq mask 0x8
pnpbios: handle 12 device ID PNP0501 (0105d041)
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc8fff,0xc9800-0xca7ff,0xca800-0xcb7ff on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
atkbd0: [GIANT-LOCKED]
psm0: current command byte:0065
psm0: failed to reset the aux device.
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fdc0 failed to probe at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
ppc0: parallel port not found.
ppc0: <Parallel port> failed to probe at irq 7 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: irq maps: 0x1 0x11 0x1 0x1
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: irq maps: 0x1 0x9 0x1 0x1
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
unknown: <PNP0c01> can't assign resources (memory)
unknown: <PNP0c01> at iomem 0-0x9fbff,0x9fc00-0x9ffff,0xe0000-0xfffff,0x100000-0x7fffffff,0xfec00000-0xfec00fff,0xfec01000-0xfec01fff,0xfee00000-0xfee00fff on isa0
unknown: <PNP0303> can't assign resources (port)
unknown: <PNP0303> at port 0x60 on isa0
unknown: <PNP0800> failed to probe at port 0x61 on isa0
unknown: <PNP0c02> can't assign resources (port)
unknown: <PNP0c02> at port 0x580-0x58f on isa0
unknown: <PNP0501> can't assign resources (port)
unknown: <PNP0501> at port 0x3f8-0x3ff on isa0
unknown: <PNP0501> can't assign resources (port)
unknown: <PNP0501> at port 0x2f8-0x2ff on isa0
Device configuration finished.
Reducing kern.maxvnodes 134371 -> 100000
procfs registered
Timecounter "TSC" frequency 996845270 Hz quality 800
Timecounters tick every 1.000 msec
lo0: bpf attached
ata1-master: pio=PIO4 wdma=WDMA2 udma=UDMA33 cable=40 wire
acd0: setting PIO4 on ServerWorks ROSB4 chip
acd0: setting UDMA33 on ServerWorks ROSB4 chip
acd0: <CREATIVE CD5233E-N/0.20> CDROM drive at ata1 as master
acd0: 128KB buffer, UDMA33
acd0: Reads: CDR, CDRW, CDDA stream, packet
acd0: Writes:
acd0: Audio: play, 255 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
twed0: <Unit 2, RAID0, Normal> on twe0
twed0: 38183MB (78199808 sectors)
ATA PseudoRAID loaded
GEOM: new disk twed0
Trying to mount root from ufs:/dev/twed0s1a
start_init: trying /sbin/init
Loading configuration files.
kernel dumps on /dev/twed0s1b
Entropy harvesting:
interrupts
ethernet
point_to_point
kickstart
.
swapon: adding /dev/twed0s1b as swap device
Starting file system checks:
/dev/twed0s1a: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/twed0s1a: clean, 8070344 free (24976 frags, 1005671 blocks, 0.3% fragmentation)
Setting hostname: ikker.markir.net.
vfs.read_max:
8
->
16
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3
inet 127.0.0.1 netmask 0xff000000
fxp0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
options=8<VLAN_MTU>
inet6 fe80::2e0:81ff:fe03:55e2%fxp0 prefixlen 64 tentative scopeid 0x1
inet 192.168.1.9 netmask 0xffffff00 broadcast 192.168.1.255
ether 00:e0:81:03:55:e2
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
add net default: gateway 192.168.1.1
Additional routing options:
.
Starting devd.
Mounting NFS file systems:
.
Creating and/or trimming log files:
.
Starting syslogd.
Checking for core dump on /dev/twed0s1b...
savecore: no dumps found
ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/X11R6/lib /usr/local/lib
a.out ldconfig path: /usr/lib/aout /usr/lib/compat/aout /usr/X11R6/lib/aout
Starting local daemons:
.
Updating motd
.
Configuring syscons:
blanktime
.
Starting sshd.
Initial i386 initialization:
.
Additional ABI support:
.
Starting cron.
Local package initialization:
.
Additional TCP options:
.
Starting background file system checks in 60 seconds.
Wed Nov 16 19:55:55 NZDT 2005
Nov 16 19:56:01 ikker login: ROOT LOGIN (root) ON ttyv0
-------------- next part --------------
--- GENERIC Wed Nov 16 20:09:47 2005
+++ STANDARD Wed Nov 16 20:09:34 2005
@@ -1,11 +1,12 @@
#
-# GENERIC -- Generic kernel configuration file for FreeBSD/i386
+# STANDARD -- Kernel configuration file for FreeBSD/i386
+#
machine i386
-cpu I486_CPU
-cpu I586_CPU
+#cpu I486_CPU
+#cpu I586_CPU
cpu I686_CPU
-ident GENERIC
+ident STANDARD
# To statically compile in device wiring instead of /boot/device.hints
#hints "GENERIC.hints" # Default places to look for devices.
@@ -45,6 +46,7 @@
options AHD_REG_PRETTY_PRINT # Print register bitfields in debug
# output. Adds ~215k to driver.
options ADAPTIVE_GIANT # Giant mutex is adaptive.
+options SMP # Symmetric MultiProcessor Kernel
device apic # I/O APIC
-------------- next part --------------
# mptable -verbose -grope
===============================================================================
MPTable
looking for EBDA pointer @ 0x040e, found, searching EBDA @ 0x0009fc00
searching CMOS 'top of mem' @ 0x0009f000 (636K)
searching default 'top of mem' @ 0x0009fc00 (639K)
searching BIOS @ 0x000f0000
searching extended BIOS @ 0x000e0000
groping memory @ 0x00080000
groping memory @ 0x00090000
MP FPS NOT found,
suggest trying -grope option!!!
More information about the freebsd-smp
mailing list