Automatic unit start broken?

Bernd Walter ticso at cicely12.cicely.de
Tue Feb 28 08:26:57 PST 2006


On Tue, Feb 28, 2006 at 09:10:04AM -0700, Kenneth D. Merry wrote:
> On Mon, Feb 27, 2006 at 21:43:27 +0100, Bernd Walter wrote:
> > On Mon, Feb 27, 2006 at 01:22:54PM -0700, Kenneth D. Merry wrote:
> > > On Mon, Feb 27, 2006 at 21:16:45 +0100, Bernd Walter wrote:
> > > What error code do your disks return?  You will probably see some console
> > > output if GEOM has tried to read metadata off the disk and that initial
> > > read fails.
> > > 
> > > If the drive returns 0x04,0x02 ("Logical unit not ready, initializing cmd.
> > > required"), CAM will attempt to spin the disk up automatically and retry
> > > the command.
> > 
> > During the first tests I waited 90s in loader to let all delayed spin
> > up drives spin up.
> > This is with recent RELENG_6 and a drive which don't spin up themself:
> > [...]
> > da7 at esp1 bus 0 target 10 lun 0
> > da7: <SEAGATE ST336706LC 8A03> Fixed Direct Access SCSI-3 device 
> > da7: 20.000MB/s transfers (10.000MHz, offset 15, 16bit), Tagged Queueing Enabled
> > da7: Attempt to query device size failed: NOT READY, Logical unit not ready, initial
> 
> That's rather odd, since it looks like you've got an 0x04,0x02 response,
> but the device must have rejected the start unit command if we failed to
> get capacity information.

At least the drive won't fail a start unit when done via camcontrol.

> > [...]
> > No GEOM message about this driver until rc sends a start command and
> > GEOM is retriggered to reread the drive:
> > Unit started successfully
> > GEOM_LABEL: Label for provider da7 is ufs/dump1.
> > The following commands were used in rc:
> > camcontrol start -n da -u 7
> > cat /dev/null > /dev/da7
> > 
> > Without the loader delay other disks are having problems as well:
> > da9 at esp1 bus 0 target 14 lun 0
> > da9: <IBM DDYS-T36950M S80D> Fixed Direct Access SCSI-3 device 
> > da9: 20.000MB/s transfers (10.000MHz, offset 15, 16bit), Tagged Queueing Enabled
> > da9: Attempt to query device size failed: NOT READY, Logical unit is in process of b
> > 
> 
> That's a different error.  We won't send a start unit in that case.  The
> error recovery action for 0x04,0x01 is to send a test unit ready every half
> second for a minute until the device becomes ready.
> Evidently it didn't become ready after that period of time.

Possible that this works, but a minute is hardly enough for a drive
with ID 14 - considered 6s per ID this means the given drive requires
84s after power-up.
But I doubt that the kernel waits - I should have noticed waiting a
whole minute.
Where is the minute defined?
If it is not solved by raising the wait to 120s it likely won't work.

> > On Shell:
> > [30]cicely19# dd if=/dev/da7 bs=1k count=1 of=/dev/null
> > 1+0 records in
> > 1+0 records out
> > 1024 bytes transferred in 0.008765 secs (116829 bytes/sec)
> > [31]cicely19# camcontrol stop -n da -u 7
> > Unit stopped successfully
> > [32]cicely19# dd if=/dev/da7 bs=1k count=1 of=/dev/null
> > dd: /dev/da7: Input/output error
> > 0+0 records in
> > 0+0 records out
> > 0 bytes transferred in 0.004810 secs (0 bytes/sec)
> > Exit 1
> 
> What errors do you see on the console at that point?  In order for CAM to
> automatically spin up the disk, it needs to send back 0x04,0x02 when it is
> spun down, and it needs to actually spin up the disk in response to a start
> unit.

I don't see anything on console.

> What happens when you:
> 
> camcontrol stop da7
> camcontrol tur da7 -v
> camcontrol start da7 -v

[52]raven# camcontrol stop da7
Unit stopped successfully
[53]raven# camcontrol tur da7 -v
Unit is not ready
(pass8:esp1:0:10:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 
(pass8:esp1:0:10:0): CAM Status: CCB request is in progress
Exit 1
[54]raven# camcontrol start da7 -v
Unit started successfully

-- 
B.Walter                   BWCT                http://www.bwct.de
bernd at bwct.de                                  info at bwct.de



More information about the freebsd-scsi mailing list