Fresh installation 9.1
hrkesh sahu
hrisikeshsahu at gmail.com
Wed May 22 07:08:20 UTC 2013
Hi ,
Thanks a lot for this quick reply.
Sorry i missed the " in the end while typing. It's a typo.
I provided the ouput of " nestat -r " and "ifconfig".
> netstat -r
--------------
routing tables -
internet :
-----------
destination Gateway
Flags Refs
Use Netif Expire
default 192.168.200.1
UGS 0
0 re0
localhost link#12
UH 0
148 lo0
192.168.100.0 link#10
U 0
0 rl0
192.168.100.101 link#10 UHS
0
0 lo0
192.168.200.0 link#5
U 0
0 re0
192.168.200.101 link#5 UHS
0
0 lo0
Internet6:
-------------------
Ipv6 details
> Ifconfig
--------------------
re0: flags=8843<UP,Broadcast,Running,Simplex,Multicast> Metric 0 mtu 1500
options=8209b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE>
ether 00:1f:d0:40:8b:bd
inet6 fe80::21f:d0ff:fe40:8bbd%re0 prefixlen 64 scopeid 0x5
inet 192.168.200.101 netmask 0xffffff00 broadcast 192.168.200.255
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
media:Enthernet autoselect (none)
status: no carrier
rl0: flags=8843<UP,Broadcast,Running,Simplex,Multicast> Metric 0 mtu 1500
options=2008<VLAN_MTU,WOL_MAGIC>
ether 00:10:b5:48:9f:73
inet6 fe80::21f:b5ff:fe48:9f73%rl0 prefixlen 64 scopeid 0xa
inet 192.168.100.101 netmask 0xffffff00 broadcast 192.168.100.255
nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
media:Enthernet autoselect (none)
status: no carrier
there is a plip0 and lo0.
Regards
Hrisikesh
On Wed, May 22, 2013 at 12:02 PM, Trond Endrestøl <
Trond.Endrestol at fagskolen.gjovik.no> wrote:
> On Wed, 22 May 2013 11:10+0530, hrkesh sahu wrote:
>
> > Hi All,
> > IPv4 Routing -
> > ------------------------
> > I disabled the DHCP from rc.conf for both the interface. but still I am
> not
> > able to route trafic from one interface to another.
> >
> > rc.conf
> > ---------------
> > hostname="idc-freebsd"
> > keymap="hy.armscii-8.kbd"
> > #ifconfig_re0="DHCP"
> > #ifconfig_rl0="DHCP"
> > dumpdev="NO"
>
> > ifconfig_rl0="inet 192.168.100.101 netmask 255.255.255.0
> > ifconfig_re0="inet 192.168.200.101 netmask 255.255.255.0
>
> Are the two lines above copied straight from your rc.conf file?
> If so, both lines are missing a " at the end. Please check to see if
> this is needed.
>
> Next, the outputs of the ifconfig command and the netstat -r command
> should reveal something interesting. Would you please post the
> results from these two commands?
>
> > ipv6_activate_all_interfaces="YES"
> > gateway_enable="YES"
> > default_router="192.168.200.1"
> >
> > I am using FreeBSD - 9.1 Release version
> >
> > I need to communicate between two different subnets.
> >
> > Am i missing anything to enable freebsd as router?
> > Do i need to add a route entry?
> >
> > If possible could you please share rc.conf file with IPv4 routing?
> >
> > Regards
> > Hrisikesh
> >
> > On Thu, May 9, 2013 at 2:04 PM, Trond Endrestøl <
> > Trond.Endrestol at fagskolen.gjovik.no> wrote:
> >
> > > On Thu, 9 May 2013 12:18+0530, hrkesh sahu wrote:
> > >
> > > > > HI All,
> > > > >
> > > > I have a FreeBSD 9.1 Release installed with TWO NIC cards. I was
> trying
> > > to
> > > > make this FreeBSD machine as a router .
> > > > This is my rc.conf
> > > > --------------------------------
> > > > ifconfig_rl0 = "inet 192.168.100.101 netmask 255.255.255.0"
> > > > ifconfig_re0="inet 192.168.200.101 netmask 255.255.255.0"
> > > >
> > > > gateway_enable = "YES"
> > > > ifconfig_rl0 = "DHCP"
> > > > ifconfig_re0 = "DHCP"
> > > >
> > > > defaultrouter = "192.168.100.1"
> > > > ipv6_activate_all_interfaces = "YES"
> > > > sshd_enable = "YES"
> > > > synchronous_dhclient="YES"
> > > >
> > > > Please help me to establish a IPv4 router.
> > > > Both the interfaces are connected to to different laptops with a
> static
> > > IP
> > > > address.
> > >
> > > You should place a # in front of the two lines:
> > >
> > > > ifconfig_rl0 = "DHCP"
> > > > ifconfig_re0 = "DHCP"
> > >
> > > Next, you probably shouldn't place spaces before and after the equal
> > > signs.
> > >
> > > > Laptop 1 = 192.168.100.102 ( connected to interface rl0) gateway -
> > > > 192.168.100.1
> > > >
> > > > Laptop 2 = 192.168.200.102 ( connected to interface re0)
> > > > ping from Laptop1 -> rl0 is successful
> > > > but ping from Laptop1 -> re0 is not successful.
> > > >
> > > > After this I want to know also How to make this as IPv6 router?
> > >
> > > See
> > >
> http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/network-ipv6.html
> > > .
> > >
> > > You probably should create a ULA prefix or two, and assign these to
> > > your router interfaces. http://www.sixxs.net/tools/grh/ula/ might help
> > > you.
> > >
> > > Something along these lines might help you achieve what you want:
> > >
> > > ifconfig_rl0_ipv6="inet6 fd8f:d6d0:e6e7:100::1 prefixlen 64"
> > > ifconfig_re0_ipv6="inet6 fd44:13de:a366:200::1 prefixlen 64"
> > > ipv6_gateway_enable="YES"
> > >
> > > Finally you probably should configure and enable Router Advertisement
> > > and Host Auto Configuration as explained in section 32.11.6 of
> > >
> http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/network-ipv6.html
> > > .
>
> --
> +-------------------------------+------------------------------------+
> | Vennlig hilsen, | Best regards, |
> | Trond Endrestøl, | Trond Endrestøl, |
> | IT-ansvarlig, | System administrator, |
> | Fagskolen Innlandet, | Gjøvik Technical College, Norway, |
> | tlf. mob. 952 62 567, | Cellular...: +47 952 62 567, |
> | sentralbord 61 14 54 00. | Switchboard: +47 61 14 54 00. |
> +-------------------------------+------------------------------------+
>
More information about the freebsd-questions
mailing list