RELENG_9 and mps driver (LSI 9211-8i)
Vincent Hoffman
vince at unsane.co.uk
Sun Jan 8 23:22:39 UTC 2012
On 08/01/2012 04:11, Dennis Glatting wrote:
> I have three LSI 9211-8i boards in my system: two flashed to T and one
> R. The Ts appear to work fine but the operating system doesn't see the
> RAID1 volume on R, but neither did RELENG_8.
>
> I am writing to ask how well R is supported, if at all. Or, since this
> my first case of using R under LSI+FreeBSD, perhaps there is common
> mistakes I may be making -- the array is stable.
I dont have one handy to test but the manpage says in the BUGS section
BUGS
This driver is still in development, it has only been tested on the
amd64
architecture and has some known shortcomings:
o No IR (Integrated RAID) support.
o No userland utility support (e.g. mptutil(8).)
o Sometimes the driver gets into a state where devices arrive and
depart multiple times, without user intervention.
o The error recovery code isn't complete.
This along with this thread
http://forums.freebsd.org/archive/index.php/t-4505.html
Indicates the R isnt fully supported, from what i can gather its fine as
JBOD so you can use zfs or one of the geom software RAIDs though.
Vince
> The boards (mps1 is the board with the RAID1 array):
>
> mps0: <LSI SAS2008> port 0xde00-0xdeff mem
> 0xfd9fc000-0xfd9fffff,0xfd980000-0xfd9bffff irq 19 at device 0.0 on pci1
> mps0: Firmware: 12.00.00.00
> mps0: IOCCapabilities:
> 1285c<ScsiTaskFull,DiagTrace,SnapBuf,EEDP,TransRetry,EventReplay,HostDisc>
> mps1: <LSI SAS2008> port 0x9e00-0x9eff mem
> 0xfdefc000-0xfdefffff,0xfde80000-0xfdebffff irq 19 at device 0.0 on pci5
> mps1: Firmware: 12.00.00.00
> mps1: IOCCapabilities:
> 185c<ScsiTaskFull,DiagTrace,SnapBuf,EEDP,TransRetry,IR>
> mps2: <LSI SAS2008> port 0x8e00-0x8eff mem
> 0xfdcfc000-0xfdcfffff,0xfdc80000-0xfdcbffff irq 16 at device 0.0 on pci6
> mps2: Firmware: 12.00.00.00
> mps2: IOCCapabilities:
> 1285c<ScsiTaskFull,DiagTrace,SnapBuf,EEDP,TransRetry,EventReplay,HostDisc>
>
>
>
> bd3# uname -a
> FreeBSD bd3 9.0-STABLE FreeBSD 9.0-STABLE #0: Sat Jan 7 16:09:10 PST
> 2012 root at bd3:/sys/amd64/compile/BULLDOZER amd64
>
> (i.e., the OS was csup against RELENG_9 and build today).
>
>
> Other data:
>
>
> bd3# dmesg
> Copyright (c) 1992-2012 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> The Regents of the University of California. All rights
> reserved.
> FreeBSD is a registered trademark of The FreeBSD Foundation.
> FreeBSD 9.0-STABLE #0: Sat Jan 7 16:09:10 PST 2012
> root at bd3:/sys/amd64/compile/BULLDOZER amd64
> CPU: AMD FX(tm)-8150 Eight-Core Processor (4017.99-MHz
> K8-class CPU)
> Origin = "AuthenticAMD" Id = 0x600f12 Family = 15 Model = 1
> Stepping = 2
>
> Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,C
> MOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
>
> Features2=0x1698220b<SSE3,PCLMULQDQ,MON,SSSE3,CX16,SSE4.1,SSE4.2,POPCNT,AESNI,
> XSAVE,AVX>
> AMD Features=0x2e500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM>
> AMD
> Features2=0x1c9bfff<LAHF,CMP,SVM,ExtAPIC,CR8,ABM,SSE4A,MAS,Prefetch,OSVW,I
> BS,XOP,SKINIT,WDT,LWP,FMA4,NodeId,Topology,<b23>,<b24>>
> TSC: P-state invariant, performance statistics
> real memory = 17179869184 (16384 MB)
> avail memory = 16508002304 (15743 MB)
> Event timer "LAPIC" quality 400
> ACPI APIC Table: <GBT GBTUACPI>
> FreeBSD/SMP: Multiprocessor System Detected: 8 CPUs
> FreeBSD/SMP: 1 package(s) x 8 core(s)
> cpu0 (BSP): APIC ID: 0
> cpu1 (AP): APIC ID: 1
> cpu2 (AP): APIC ID: 2
> cpu3 (AP): APIC ID: 3
> cpu4 (AP): APIC ID: 4
> cpu5 (AP): APIC ID: 5
> cpu6 (AP): APIC ID: 6
> cpu7 (AP): APIC ID: 7
> ioapic0: Changing APIC ID to 8
> ioapic0 <Version 2.1> irqs 0-23 on motherboard
> kbd1 at kbdmux0
> acpi0: <GBT GBTUACPI> on motherboard
> acpi0: Power Button (fixed)
> acpi0: reservation of 0, a0000 (3) failed
> acpi0: reservation of 100000, cfca0000 (3) failed
> Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
> acpi_timer0: <32-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
> cpu0: <ACPI CPU> on acpi0
> cpu1: <ACPI CPU> on acpi0
> cpu2: <ACPI CPU> on acpi0
> cpu3: <ACPI CPU> on acpi0
> cpu4: <ACPI CPU> on acpi0
> cpu5: <ACPI CPU> on acpi0
> cpu6: <ACPI CPU> on acpi0
> cpu7: <ACPI CPU> on acpi0
> acpi_button0: <Power Button> on acpi0
> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
> pci0: <ACPI PCI bus> on pcib0
> pci0: <base peripheral> at device 0.2 (no driver attached)
> pcib1: <ACPI PCI-PCI bridge> irq 19 at device 3.0 on pci0
> pci1: <ACPI PCI bus> on pcib1
> mps0: <LSI SAS2008> port 0xde00-0xdeff mem
> 0xfd9fc000-0xfd9fffff,0xfd980000-0xfd
> 9bffff irq 19 at device 0.0 on pci1
> mps0: Firmware: 12.00.00.00
> mps0: IOCCapabilities:
> 1285c<ScsiTaskFull,DiagTrace,SnapBuf,EEDP,TransRetry,Even
> tReplay,HostDisc>
> pcib2: <ACPI PCI-PCI bridge> irq 16 at device 4.0 on pci0
> pci2: <ACPI PCI bus> on pcib2
> em0: <Intel(R) PRO/1000 Network Connection 7.2.3> port 0xcf00-0xcf1f mem
> 0xfd7c0
> 000-0xfd7dffff,0xfd700000-0xfd77ffff,0xfd7fc000-0xfd7fffff irq 16 at
> device 0.0
> on pci2
> em0: Using MSIX interrupts with 3 vectors
> em0: Ethernet address: 00:1b:21:c6:d2:a0
> pcib3: <ACPI PCI-PCI bridge> irq 17 at device 9.0 on pci0
> pci3: <ACPI PCI bus> on pcib3
> xhci0: <XHCI (generic) USB 3.0 controller> mem 0xfd5f8000-0xfd5fffff irq
> 17 at d
> evice 0.0 on pci3
> xhci0: 64 byte context size.
> usbus0 on xhci0
> pcib4: <ACPI PCI-PCI bridge> irq 18 at device 10.0 on pci0
> pci4: <ACPI PCI bus> on pcib4
> ahci0: <Marvell 88SE9172 AHCI SATA controller> port
> 0xaf00-0xaf07,0xae00-0xae03,
> 0xad00-0xad07,0xac00-0xac03,0xab00-0xab0f mem 0xfcbff000-0xfcbff1ff irq
> 18 at de
> vice 0.0 on pci4
> ahci0: AHCI v1.00 with 2 6Gbps ports, Port Multiplier supported with FBS
> ahcich0: <AHCI channel> at channel 0 on ahci0
> ahcich1: <AHCI channel> at channel 1 on ahci0
> pcib5: <ACPI PCI-PCI bridge> irq 19 at device 11.0 on pci0
> pci5: <ACPI PCI bus> on pcib5
> mps1: <LSI SAS2008> port 0x9e00-0x9eff mem
> 0xfdefc000-0xfdefffff,0xfde80000-0xfd
> ebffff irq 19 at device 0.0 on pci5
> mps1: Firmware: 12.00.00.00
> mps1: IOCCapabilities:
> 185c<ScsiTaskFull,DiagTrace,SnapBuf,EEDP,TransRetry,IR>
> pcib6: <ACPI PCI-PCI bridge> irq 16 at device 12.0 on pci0
> pci6: <ACPI PCI bus> on pcib6
> mps2: <LSI SAS2008> port 0x8e00-0x8eff mem
> 0xfdcfc000-0xfdcfffff,0xfdc80000-0xfd
> cbffff irq 16 at device 0.0 on pci6
> mps2: Firmware: 12.00.00.00
> mps2: IOCCapabilities:
> 1285c<ScsiTaskFull,DiagTrace,SnapBuf,EEDP,TransRetry,Even
> tReplay,HostDisc>
> pcib7: <ACPI PCI-PCI bridge> irq 17 at device 13.0 on pci0
> pci7: <ACPI PCI bus> on pcib7
> vgapci0: <VGA-compatible display> port 0xee00-0xeeff mem
> 0xd0000000-0xdfffffff,0
> xfdac0000-0xfdadffff irq 17 at device 0.0 on pci7
> hdac0: <ATI (Unknown) High Definition Audio Controller> mem
> 0xfdafc000-0xfdaffff
> f irq 18 at device 0.1 on pci7
> ahci1: <ATI IXP700 AHCI SATA controller> port
> 0xff00-0xff07,0xfe00-0xfe03,0xfd00
> -0xfd07,0xfc00-0xfc03,0xfb00-0xfb0f mem 0xfdfff000-0xfdfff3ff irq 19 at
> device 1
> 7.0 on pci0
> ahci1: AHCI v1.20 with 4 6Gbps ports, Port Multiplier supported
> ahcich2: <AHCI channel> at channel 0 on ahci1
> ahcich3: <AHCI channel> at channel 1 on ahci1
> ahcich4: <AHCI channel> at channel 2 on ahci1
> ahcich5: <AHCI channel> at channel 3 on ahci1
> ohci0: <OHCI (generic) USB controller> mem 0xfdffe000-0xfdffefff irq 18
> at devic
> e 18.0 on pci0
> usbus1: <OHCI (generic) USB controller> on ohci0
> ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfdffd000-0xfdffd0ff irq
> 17 at d
> evice 18.2 on pci0
> usbus2: EHCI version 1.0
> usbus2: <EHCI (generic) USB 2.0 controller> on ehci0
> ohci1: <OHCI (generic) USB controller> mem 0xfdffc000-0xfdffcfff irq 18
> at devic
> e 19.0 on pci0
> usbus3: <OHCI (generic) USB controller> on ohci1
> ehci1: <EHCI (generic) USB 2.0 controller> mem 0xfdffb000-0xfdffb0ff irq
> 17 at d
> evice 19.2 on pci0
> usbus4: EHCI version 1.0
> usbus4: <EHCI (generic) USB 2.0 controller> on ehci1
> pci0: <serial bus, SMBus> at device 20.0 (no driver attached)
> atapci0: <ATI IXP700/800 UDMA133 controller> port
> 0x1f0-0x1f7,0x3f6,0x170-0x177,
> 0x376,0xfa00-0xfa0f at device 20.1 on pci0
> ata0: <ATA channel> at channel 0 on atapci0
> ata1: <ATA channel> at channel 1 on atapci0
> isab0: <PCI-ISA bridge> at device 20.3 on pci0
> isa0: <ISA bus> on isab0
> pcib8: <ACPI PCI-PCI bridge> at device 20.4 on pci0
> pci8: <ACPI PCI bus> on pcib8
> ohci2: <OHCI (generic) USB controller> mem 0xfdffa000-0xfdffafff irq 18
> at devic
> e 20.5 on pci0
> usbus5: <OHCI (generic) USB controller> on ohci2
> pcib9: <ACPI PCI-PCI bridge> at device 21.0 on pci0
> pci9: <ACPI PCI bus> on pcib9
> re0: <RealTek 8168/8111 B/C/CP/D/DP/E/F PCIe Gigabit Ethernet> port
> 0x6e00-0x6ef
> f mem 0xfd0ff000-0xfd0fffff,0xfd0f8000-0xfd0fbfff irq 17 at device 0.0
> on pci9
> re0: Using 1 MSI-X message
> re0: Chip rev. 0x2c800000
> re0: MAC rev. 0x00000000
> miibus0: <MII bus> on re0
> rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on
> miibus0
> rgephy0: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX,
> 100baseTX-FDX
> , 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, 1000baseT-FDX,
> 1000baseT-FDX-
> master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow
> re0: Ethernet address: 50:e5:49:45:55:8e
> pcib10: <ACPI PCI-PCI bridge> at device 21.1 on pci0
> pci10: <ACPI PCI bus> on pcib10
> xhci1: <XHCI (generic) USB 3.0 controller> mem 0xfcff8000-0xfcffffff irq
> 17 at d
> evice 0.0 on pci10
> xhci1: 64 byte context size.
> usbus6 on xhci1
> pcib11: <ACPI PCI-PCI bridge> at device 21.2 on pci0
> pci11: <ACPI PCI bus> on pcib11
> ahci2: <Marvell 88SE9172 AHCI SATA controller> port
> 0x3f00-0x3f07,0x3e00-0x3e03,
> 0x3d00-0x3d07,0x3c00-0x3c03,0x3b00-0x3b0f mem 0xfcdff000-0xfcdff1ff irq
> 17 at de
> vice 0.0 on pci11
> ahci2: AHCI v1.00 with 2 6Gbps ports, Port Multiplier supported with FBS
> ahcich6: <AHCI channel> at channel 0 on ahci2
> ahcich7: <AHCI channel> at channel 1 on ahci2
> ohci3: <OHCI (generic) USB controller> mem 0xfdff9000-0xfdff9fff irq 18
> at devic
> e 22.0 on pci0
> usbus7: <OHCI (generic) USB controller> on ohci3
> ehci2: <EHCI (generic) USB 2.0 controller> mem 0xfdff8000-0xfdff80ff irq
> 17 at d
> evice 22.2 on pci0
> usbus8: EHCI version 1.0
> usbus8: <EHCI (generic) USB 2.0 controller> on ehci2
> attimer0: <AT timer> port 0x40-0x43 on acpi0
> Timecounter "i8254" frequency 1193182 Hz quality 0
> Event timer "i8254" frequency 1193182 Hz quality 100
> hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff irq 0,8
> on acpi0
> Timecounter "HPET" frequency 14318180 Hz quality 950
> atrtc0: <AT realtime clock> port 0x70-0x73 on acpi0
> Event timer "RTC" frequency 32768 Hz quality 0
> orm0: <ISA Option ROMs> at iomem
> 0xc0000-0xcffff,0xd5000-0xdafff,0xdb000-0xdbfff
> on isa0
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
> isa0
> atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
> atkbd0: <AT Keyboard> irq 1 on atkbdc0
> kbd0 at atkbd0
> atkbd0: [GIANT-LOCKED]
> ppc0: cannot reserve I/O port range
> hwpstate0: <Cool`n'Quiet 2.0> on cpu0
> Timecounters tick every 1.000 msec
> hdac0: HDA Codec #0: ATI R6xx HDMI
> pcm0: <HDA ATI R6xx HDMI PCM #0 HDMI> at cad 0 nid 1 on hdac0
> usbus0: 5.0Gbps Super Speed USB v3.0
> usbus1: 12Mbps Full Speed USB v1.0
> usbus2: 480Mbps High Speed USB v2.0
> usbus3: 12Mbps Full Speed USB v1.0
> usbus4: 480Mbps High Speed USB v2.0
> usbus5: 12Mbps Full Speed USB v1.0
> usbus6: 5.0Gbps Super Speed USB v3.0
> usbus7: 12Mbps Full Speed USB v1.0
> usbus8: 480Mbps High Speed USB v2.0
> ugen0.1: <0x1b6f> at usbus0
> uhub0: <0x1b6f XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on
> usbus0
> ugen1.1: <ATI> at usbus1
> uhub1: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
> ugen2.1: <ATI> at usbus2
> uhub2: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
> ugen3.1: <ATI> at usbus3
> uhub3: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
> ugen4.1: <ATI> at usbus4
> uhub4: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus4
> ugen5.1: <ATI> at usbus5
> uhub5: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5
> ugen6.1: <0x1b6f> at usbus6
> uhub6: <0x1b6f XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on
> usbus6
> ugen7.1: <ATI> at usbus7
> uhub7: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus7
> ugen8.1: <ATI> at usbus8
> uhub8: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus8
> uhub5: 2 ports with 2 removable, self powered
> uhub7: 4 ports with 4 removable, self powered
> uhub1: 5 ports with 5 removable, self powered
> uhub3: 5 ports with 5 removable, self powered
> uhub0: 4 ports with 4 removable, self powered
> uhub6: 4 ports with 4 removable, self powered
> uhub8: 4 ports with 4 removable, self powered
> uhub2: 5 ports with 5 removable, self powered
> uhub4: 5 ports with 5 removable, self powered
> ugen1.2: <BTC> at usbus1
> ukbd0: <BTC USB Multimedia Keyboard, class 0/0, rev 1.10/1.00, addr 2>
> on usbus1
> kbd2 at ukbd0
> uhid0: <BTC USB Multimedia Keyboard, class 0/0, rev 1.10/1.00, addr 2>
> on usbus1
> ada0 at ahcich2 bus 0 scbus5 target 0 lun 0
> ada0: <Corsair Force 3 SSD 1.3.3> ATA-8 SATA 3.x device
> ada0: 600.000MB/s transfers (SATA 3.x, UDMA6, PIO 8192bytes)
> ada0: Command Queueing enabled
> ada0: 85857MB (175836528 512 byte sectors: 16H 63S/T 16383C)
> ada0: Previously was known as ad8
> ada1 at ahcich3 bus 0 scbus6 target 0 lun 0
> ada1: <OCZ-AGILITY2 1.33> ATA-8 SATA 2.x device
> ada1: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
> ada1: Command Queueing enabled
> ada1: 57241MB (117231408 512 byte sectors: 16H 63S/T 16383C)
> ada1: Previously was known as ad10
> ada2 at ahcich4 bus 0 scbus7 target 0 lun 0
> ada2: <ST31000333AS SD35> ATA-8 SATA 2.x device
> ada2: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
> ada2: Command Queueing enabled
> ada2: 953869MB (1953525168 512 byte sectors: 16H 63S/T 16383C)
> ada2: Previously was known as ad12
> da7 at mps0 bus 0 scbus0 target 7 lun 0
> da7: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device
> da7: 300.000MB/s transfers
> da7: Command Queueing enabled
> da7: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C)
> da3 at mps0 bus 0 scbus0 target 3 lun 0
> da3: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device
> da3: 300.000MB/s transfers
> da3: Command Queueing enabled
> da3: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C)
> da0 at mps0 bus 0 scbus0 target 0 lun 0
> da0: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device
> da0: 300.000MB/s transfers
> da0: Command Queueing enabled
> da0: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C)
> da9 at mps2 bus 0 scbus4 target 1 lun 0
> da9: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device
> da9: 300.000MB/s transfers
> da9: Command Queueing enabled
> da9: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C)
> da10 at mps2 bus 0 scbus4 target 2 lun 0
> da10: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device
> da10: 300.000MB/s transfers
> da10: Command Queueing enabled
> da10: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C)
> da8 at mps2 bus 0 scbus4 target 0 lun 0
> da8: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device
> da8: 300.000MB/s transfers
> da8: Command Queueing enabled
> da8: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C)
> da11 at mps2 bus 0 scbus4 target 3 lun 0
> da11: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device
> da11: 300.000MB/s transfers
> da11: Command Queueing enabled
> da11: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C)
> da6 at mps0 bus 0 scbus0 target 6 lun 0
> da6: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device
> da6: 300.000MB/s transfers
> da6: Command Queueing enabled
> da6: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C)
> da4 at mps0 bus 0 scbus0 target 4 lun 0
> da4: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device
> da4: 300.000MB/s transfers
> da4: Command Queueing enabled
> da4: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C)
> da5 at mps0 bus 0 scbus0 target 5 lun 0
> da5: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device
> da5: 300.000MB/s transfers
> da5: Command Queueing enabled
> da5: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C)
> da1 at mps0 bus 0 scbus0 target 1 lun 0
> da1: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device
> da1: 300.000MB/s transfers
> da1: Command Queueing enabled
> da1: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C)
> da2 at mps0 bus 0 scbus0 target 2 lun 0
> da2: <ATA WDC WD25EZRS-00J 0A80> Fixed Direct Access SCSI-6 device
> da2: 300.000MB/s transfers
> da2: Command Queueing enabled
> da2: 2384658MB (4883781168 512 byte sectors: 255H 63S/T 304001C)
> SMP: AP CPU #1 Launched!
> SMP: AP CPU #4 Launched!
> SMP: AP CPU #6 Launched!
> SMP: AP CPU #5 Launched!
> SMP: AP CPU #2 Launched!
> SMP: AP CPU #7 Launched!
> SMP: AP CPU #3 Launched!
> Timecounter "TSC-low" frequency 15695275 Hz quality 1000
> Trying to mount root from ufs:/dev/gpt/disk0 [rw]...
> ZFS filesystem version 5
> ZFS storage pool version 28
>
>
> _______________________________________________
> freebsd-questions at freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-questions
> To unsubscribe, send any mail to "freebsd-questions-unsubscribe at freebsd.org"
More information about the freebsd-questions
mailing list