USB-to-serial adapter configuration
Saifi Khan
saifi.khan at twincling.org
Mon May 18 13:02:35 UTC 2009
On Mon, 18 May 2009, Ruben de Groot wrote:
> On Mon, May 18, 2009 at 04:07:09PM +0000, Saifi Khan typed:
> > Hi all:
> >
> > How does one configure settings for USB-to-serial adapter in FreeBSD ?
> >
> > The one i have purchased is
> > http://www.usbgear.com/computer_cable_details.cfm?sku=CHEAP-SERIAL&cats=199&catid=482%2C1303%2C199%2C461%2C106%2C1009%2C601
> >
> > On the Gentoo box, 'lsusb' displays it as:
> > Bus 002 Device 003: ID 067b:2303
> > Prolific Technology, Inc. PL2303 Serial Port
>
> Your adapter should be recognised by the uplcom driver. put uplcom_load="YES" in loader.conf
> or load manually. Check dmesg for the device name.
> Also, I think cu is "good enough" ;)
>
> Ruben
>
This is the error shown in 'dmesg' log
ugen0.2: <Prolific Technology> at usbus0
uplcom0: <Prolific Technology PL2303 Serial (ATEN/IOGEAR UC232A), class 0/0, rev 1.10/3.00, addr 2> on usbus0
uplcom0: init failed!
device_attach: uplcom0 attach returned 6
uplcom0: <Prolific Technology PL2303 Serial (ATEN/IOGEAR UC232A), class 0/0, rev 1.10/3.00, addr 2> on usbus0
uplcom0: init failed!
device_attach: uplcom0 attach returned 6
Scenarios:
1. kldstat -v | grep uplcom shows
303 uhub/uplcom
2. uplcom_load="YES" in /boot/loader.conf
with a reboot
In both the scenarios, 'dmesg' shows the same error.
On re-attaching the device, the following error is shown.
usb2_alloc_device:1574: set address 2 failed (USB_ERR_STALLED, ignored)
usb2_alloc_device:1612: getting device descriptor at addr 2 failed, USB_ERR_STALLED!
ugen0.2: <> at usbus0 (disconnected)
uhub_reattach_port:417: could not allocate new device!
The output from 'usbconfig dump_info' shows
ugen3.1: <UHCI root HUB Intel> at usbus3, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON
ugen4.1: <EHCI root HUB Intel> at usbus4, cfg=0 md=HOST spd=HIGH (480Mbps) pwr=ON
ugen0.1: <UHCI root HUB Intel> at usbus0, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON
ugen1.1: <UHCI root HUB Intel> at usbus1, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON
ugen2.1: <UHCI root HUB Intel> at usbus2, cfg=0 md=HOST spd=FULL (12Mbps) pwr=ON
The 'dmesg' extract of USB is as follows:
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 12Mbps Full Speed USB v1.0
uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
ugen4.1: <Intel> at usbus4
uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus4
ugen0.1: <Intel> at usbus0
uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub3: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <Intel> at usbus2
uhub4: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
Root mount waiting for: usbus4 usbus3 usbus2 usbus1 usbus0
uhub0: 2 ports with 2 removable, self powered
uhub2: 2 ports with 2 removable, self powered
uhub3: 2 ports with 2 removable, self powered
uhub4: 2 ports with 2 removable, self powered
Root mount waiting for: usbus4
Root mount waiting for: usbus4
Root mount waiting for: usbus4
uhub1: 8 ports with 8 removable, self powered
Here is the system information.
FreeBSD bsd 8.0-CURRENT-200905 FreeBSD 8.0-CURRENT-200905 #0: Mon May 4 23:25:09 UTC 2009 root at almeida.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC i386
Any suggestions on how i can get uplcom drive to work ?
thanks
Saifi.
More information about the freebsd-questions
mailing list