SATA flash drive vs 7.0
perryh at pluto.rain.com
perryh at pluto.rain.com
Mon May 4 05:48:37 UTC 2009
Should FreeBSD handle SATA-attached flash drives?
I have added a 64GB Patriot flash drive to a 7.0 system, but it does
not seem to be working properly. Pertinent parts of dmesg.boot:
FreeBSD 7.0-RELEASE #0: Sun Feb 24 19:59:52 UTC 2008
root at logan.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Pentium II/Pentium II Xeon/Celeron (449.85-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x652 Stepping = 2
Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
real memory = 67100672 (63 MB)
avail memory = 51662848 (49 MB)
...
atapci1: <VIA 6421 SATA150 controller> port 0x1800-0x180f,0x14f0-0x14ff,0x14e0-0x14ef,0x14d0-0x14df,0x14a0-0x14bf,0x1000-0x10ff irq 9 at device 16.0 on pci0
atapci1: [ITHREAD]
ata2: <ATA channel 0> on atapci1
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci1
ata3: [ITHREAD]
ata4: <ATA channel 2> on atapci1
ata4: [ITHREAD]
...
ad6: FAILURE - SET_MULTI status=51<READY,DSC,ERROR> error=4<ABORTED>
ad6: 61136MB <PATRIOT MEMORY 64GB SSD 02.10104> at ata3-master SATA150
At first things look OK:
$ ls -l /dev/ad6*
crw-r----- 1 root operator 0, 88 May 3 20:30 /dev/ad6
$ file -s /dev/ad6
/dev/ad6: x86 boot sector, Microsoft Windows XP MBR, Serial 0x9e5523de
$ grep -w ad6 /usr/local/etc/mtools.conf
drive f: file="/dev/ad6"
$ mdir f:
init F: non DOS media
Cannot initialize 'F:'
Now this seems a bit odd: file(1) says it's a Windows disk, but
mdir(1) says it isn't. (Note that there are no slices, else the
initial ls(1) should have shown them.) Then, when I tried to
investigate further by examining the contents of the drive with
"od -c /dev/ad6 | more", I got one screenful of output followed
by (on console and in dmesg):
interrupt storm detected on "irq9:"; throttling interrupt source
interrupt storm detected on "irq9:"; throttling interrupt source
interrupt storm detected on "irq9:"; throttling interrupt source
interrupt storm detected on "irq9:"; throttling interrupt source
interrupt storm detected on "irq9:"; throttling interrupt source
ad6: FAILURE - SET_MULTI status=51<READY,DSC,ERROR> error=4<ABORTED>
ad6: TIMEOUT - READ_DMA retrying (1 retry left) LBA=10712
interrupt storm detected on "irq9:"; throttling interrupt source
interrupt storm detected on "irq9:"; throttling interrupt source
interrupt storm detected on "irq9:"; throttling interrupt source
interrupt storm detected on "irq9:"; throttling interrupt source
interrupt storm detected on "irq9:"; throttling interrupt source
ad6: FAILURE - SET_MULTI status=51<READY,DSC,ERROR> error=4<ABORTED>
ad6: TIMEOUT - READ_DMA retrying (1 retry left) LBA=136936
etc. etc. until I killed it with ^C. (Just entering "q", to cause
more(1) to exit and presumably stop od(1) with a SIGPIPE, did not
stop the spew of messages.)
What does this indicate? Bad drive? Controller? Configuration?
PEBCAK?
More information about the freebsd-questions
mailing list