Network interface dc0 fails to negotiate media type
John Thorup
john.thorup.dk at gmail.com
Sun Jun 14 21:08:42 UTC 2009
I have installed FreeBSD 7.2-RELEASE i386 on a Fujitsu Siemens Scaleo
T P 340 0 1,0G PC (mainboard name D1826-G).
$ uname -a
FreeBSD dhcppc0.thorup 7.2-RELEASE FreeBSD 7.2-RELEASE #0:
Fri May 1 08:49:13 UTC 2009
root at walker.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC i386
$
I will mention that I have csup'ed and updated my ports the 31.th May.
Some time after that the network (interface dc0) suddenly stopped working.
First I saw it was not possible to get an IP address from my router.
I thought initially that it was the network cable or router, that
caused the problem but the PC can still boot up with Win XP without
any network connectivity problems.
I can see that there must be problems with the negotiation of media
type and options from:
$ ifconfig -m dc0
dc0: flags=8847<UP,BROADCAST,DEBUG,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=8<VLAN_MTU>
capabilities=8<VLAN_MTU>
ether 00:30:05:d4:25:c7
inet 0.0.0.0 netmask 0xff000000 broadcast 255.255.255.255
media: Ethernet autoselect (none)
status: active
supported media:
media autoselect
media 10baseT/UTP mediaopt full-duplex
media none
$
The strange thing is that the normal selection "media 100baseTX
mediaopt full-duplex" (before this error) are not on the list of
supported meadia.
When I boot up in Win XP, the negotiation ends up with 100baseTX / full-duplex.
If I try to configure "sudo ifconfig dc0 media 100baseTX mediaopt
full-duplex", I receive the answer "ifconfig: SIOCSIFMEDIA (media):
Device not configured".
If I try to configure "sudo ifconfig dc0 media 10baseT/UTP mediaopt
full-duplex", the command changes the settings.
I have been studying the FreeBSD man pages, reading the Handbook,
searching the mailing lists and searching the internet without finding
something that did could help me.
Can you at freebsd-questions at freebsd.org help me, so that I can get my
network up and running again.
dmesg output and sysctl's of interest:
$ dmesg
Copyright (c) 1992-2009 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.2-RELEASE #0: Fri May 1 08:49:13 UTC 2009
root at walker.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Pentium(R) 4 CPU 3.40GHz (3401.05-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf34 Stepping = 4
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0x441d<SSE3,DTES64,MON,DS_CPL,CNXT-ID,xTPR>
Logical CPUs per core: 2
real memory = 1072627712 (1022 MB)
avail memory = 1035931648 (987 MB)
ACPI APIC Table: <FSC APIC >
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP/HT): APIC ID: 1
ioapic0 <Version 2.0> irqs 0-23 on motherboard
kbd1 at kbdmux0
acpi0: <PTLTD XSDT> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0xf008-0xf00b on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0x4000-0x40ff mem
0xe0000000-0xefffffff,0xf0100000-0xf010ffff irq 16 at device 0.0 on
pci1
vgapci1: <VGA-compatible display> mem 0xf0110000-0xf011ffff at device
0.1 on pci1
pci0: <multimedia, HDA> at device 27.0 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> irq 17 at device 28.0 on pci0
pci3: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> irq 16 at device 28.1 on pci0
pci5: <ACPI PCI bus> on pcib3
pcib4: <ACPI PCI-PCI bridge> irq 18 at device 28.2 on pci0
pci7: <ACPI PCI bus> on pcib4
pcib5: <ACPI PCI-PCI bridge> irq 19 at device 28.3 on pci0
pci9: <ACPI PCI bus> on pcib5
uhci0: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-A> port
0x2000-0x201f irq 23 at device 29.0 on pci0
uhci0: [GIANT-LOCKED]
uhci0: [ITHREAD]
usb0: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-B> port
0x2400-0x241f irq 22 at device 29.1 on pci0
uhci1: [GIANT-LOCKED]
uhci1: [ITHREAD]
usb1: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-C> port
0x2800-0x281f irq 21 at device 29.2 on pci0
uhci2: [GIANT-LOCKED]
uhci2: [ITHREAD]
usb2: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb2
uhub2: 2 ports with 2 removable, self powered
uhci3: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-D> port
0x2c00-0x2c1f irq 20 at device 29.3 on pci0
uhci3: [GIANT-LOCKED]
uhci3: [ITHREAD]
usb3: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-D> on uhci3
usb3: USB revision 1.0
uhub3: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb3
uhub3: 2 ports with 2 removable, self powered
ehci0: <Intel 82801FB (ICH6) USB 2.0 controller> mem
0xf0004000-0xf00043ff irq 23 at device 29.7 on pci0
ehci0: [GIANT-LOCKED]
ehci0: [ITHREAD]
usb4: EHCI version 1.0
usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3
usb4: <Intel 82801FB (ICH6) USB 2.0 controller> on ehci0
usb4: USB revision 2.0
uhub4: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb4
uhub4: 8 ports with 8 removable, self powered
ugen0: <GlobespanVirata Cohiba 3887 rev0, class 0/0, rev 2.00/10.40,
addr 2> on uhub4
pcib6: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci11: <ACPI PCI bus> on pcib6
dc0: <ADMtek AN985 10/100BaseTX> port 0x5000-0x50ff
mem 0xf0201000-0xf02013ff irq 23 at device 4.0 on pci11
miibus0: <MII bus> on dc0
ukphy0: <Generic IEEE 802.3u media interface> PHY 1 on miibus0
ukphy0: 10baseT-FDX, auto
dc0: Ethernet address: 00:30:05:d4:25:c7
dc0: [ITHREAD]
fwohci0: <Lucent FW322/323> mem 0xf0200000-0xf0200fff irq 20 at device
6.0 on pci11
fwohci0: [FILTER]
fwohci0: OHCI version 1.0 (ROM=1)
fwohci0: No. of Isochronous channels is 8.
fwohci0: EUI64 00:30:05:b3:50:01:dd:d6
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:30:05:01:dd:d6
fwe0: Ethernet address: 02:30:05:01:dd:d6
fwip0: <IP over FireWire> on firewire0
fwip0: Firewire address: 00:30:05:b3:50:01:dd:d6 @ 0xfffe00000000,
S400, maxrec 2048
sbp0: <SBP-2/SCSI over FireWire> on firewire0
dcons_crom0: <dcons configuration ROM> on firewire0
dcons_crom0: bus_addr 0x108c000
fwohci0: Initiate bus reset
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=2, CYCLEMASTER mode
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH6 UDMA100 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x3400-0x340f at device 31.1 on
pci0
ata0: <ATA channel 0> on atapci0
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
ata1: [ITHREAD]
atapci1: <Intel AHCI controller> port
0x3430-0x3437,0x3424-0x3427,0x3428-0x342f,0x3420-0x3423,0x3410-0x341f
mem 0xf0004400-0xf00047ff irq 19 at device 31.2 on pci0
atapci1: [ITHREAD]
atapci1: AHCI Version 01.00 controller with 4 ports detected
ata2: <ATA channel 0> on atapci1
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci1
ata3: port not implemented
ata3: [ITHREAD]
ata4: <ATA channel 2> on atapci1
ata4: port not implemented
ata4: [ITHREAD]
ata5: <ATA channel 3> on atapci1
ata5: port not implemented
ata5: [ITHREAD]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: [FILTER]
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
sio0: [FILTER]
cpu0: <ACPI CPU> on acpi0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
cpu1: <ACPI CPU> on acpi0
p4tcc1: <CPU Frequency Thermal Control> on cpu1
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xccfff,0xcd000-0xcdfff pnpid
ORM0000 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
ppc0: parallel port not found.
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ums0: <Logitech USB Receiver, class 0/0, rev 1.10/25.00, addr 2> on uhub2
ums0: 16 buttons and Z dir.
Timecounters tick every 1.000 msec
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
acd0: DVDROM <HL-DT-STDVD-ROM GDR8163B/0F21> at ata0-master UDMA33
acd1: DVDR <NEC DVD RW ND-2510A/2.96> at ata0-slave UDMA33
ad4: 238475MB <WDC WD2500PD-07FZB1 05.05G05> at ata2-master SATA150
GEOM_LABEL: Label for provider ad4s1 is ntfs/WINDOWS-XP.
GEOM_LABEL: Label for provider ad4s2 is ext2fs/UBUNTU.
GEOM_LABEL: Label for provider ad4s3a is ufsid/49ff54332ba6db2e.
GEOM_LABEL: Label for provider ad4s3d is ufsid/49ff543456dba19f.
GEOM_LABEL: Label for provider ad4s3e is ufsid/49ff5433f58989ab.
GEOM_LABEL: Label for provider ad4s3f is ufsid/49ff54339167a9fa.
GEOM_LABEL: Label for provider ad4s5 is ntfs/DATA.
acd0: FAILURE - INQUIRY ILLEGAL REQUEST asc=0x24 ascq=0x00
(probe7:ata0:0:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0
(probe7:ata0:0:0:0): CAM Status: SCSI Status Error
(probe7:ata0:0:0:0): SCSI Status: Check Condition
(probe7:ata0:0:0:0): NOT READY asc:3a,0
(probe7:ata0:0:0:0): Medium not present
(probe7:ata0:0:0:0): Unretryable error
(probe8:ata0:0:1:0): TEST UNIT READY. CDB: 0 0 0 0 0 0
(probe8:ata0:0:1:0): CAM Status: SCSI Status Error
(probe8:ata0:0:1:0): SCSI Status: Check Condition
(probe8:ata0:0:1:0): NOT READY asc:3a,0
(probe8:ata0:0:1:0): Medium not present sks:0x80,0xffff
(probe8:ata0:0:1:0): Unretryable error
SMP: AP CPU #1 Launched!
cd0 at ata0 bus 0 target 0 lun 0
cd0: <HL-DT-ST DVD-ROM GDR8163B 0F21> Removable CD-ROM SCSI-0 device
cd0: 33.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
cd1 at ata0 bus 0 target 1 lun 0
cd1: <_NEC DVD_RW ND-2510A 2.96> Removable CD-ROM SCSI-0 device
cd1: 33.000MB/s transfers
cd1: Attempt to query device size failed: NOT READY, Medium not present
Trying to mount root from ufs:/dev/ad4s3a
GEOM_LABEL: Label ufsid/49ff54332ba6db2e removed.
GEOM_LABEL: Label for provider ad4s3a is ufsid/49ff54332ba6db2e.
GEOM_LABEL: Label ufsid/49ff5433f58989ab removed.
GEOM_LABEL: Label for provider ad4s3e is ufsid/49ff5433f58989ab.
GEOM_LABEL: Label ufsid/49ff54339167a9fa removed.
GEOM_LABEL: Label for provider ad4s3f is ufsid/49ff54339167a9fa.
GEOM_LABEL: Label ufsid/49ff543456dba19f removed.
GEOM_LABEL: Label for provider ad4s3d is ufsid/49ff543456dba19f.
GEOM_LABEL: Label ufsid/49ff54332ba6db2e removed.
ukbd0: <CHESEN USB Keyboard, class 0/0, rev 1.10/1.10, addr 3> on uhub2
kbd2 at ukbd0
uhid0: <CHESEN USB Keyboard, class 0/0, rev 1.10/1.10, addr 3> on uhub2
GEOM_LABEL: Label ufsid/49ff5433f58989ab removed.
GEOM_LABEL: Label ufsid/49ff54339167a9fa removed.
GEOM_LABEL: Label ufsid/49ff543456dba19f removed.
fuse4bsd: version 0.3.9-pre1, FUSE ABI 7.8
GEOM_LABEL: Label ntfs/WINDOWS-XP removed.
GEOM_LABEL: Label ntfs/DATA removed.
oss_hdaudio0: [ITHREAD]
oss_hdaudio0: <Intel HD Audio> mem 0xf0000000-0xf0003fff irq 16 at
device 27.0 on pci0
osscore: mmap() not possible with currently selected sample format.
$
$ sysctl -a | grep dev.dc.0
dev.dc.0.%desc: ADMtek AN985 10/100BaseTX
dev.dc.0.%driver: dc
dev.dc.0.%location: slot=4 function=0
dev.dc.0.%pnpinfo: vendor=0x1317 device=0x0985
subvendor=0x1734 subdevice=0x100c class=0x020000
dev.dc.0.%parent: pci11
$ sysctl -a | grep miibus
dev.miibus.0.%desc: MII bus
dev.miibus.0.%driver: miibus
dev.miibus.0.%parent: dc0
dev.ukphy.0.%parent: miibus0
$ sysctl -a | grep ukphy
dev.ukphy.0.%desc: Generic IEEE 802.3u media interface
dev.ukphy.0.%driver: ukphy
dev.ukphy.0.%location: phyno=1
dev.ukphy.0.%pnpinfo: oui=0x67f83 model=0xe rev=0xc
dev.ukphy.0.%parent: miibus0
$
----
John Thorup
Aarhus, Denmark
E-mail: john.thorup.dk at gmail.com
More information about the freebsd-questions
mailing list