CD writing fails on P6T motherboard with Pioneer cdwriter

[Yuri]

Joerg Schilling wrote:
>
> OK, if this is a timeout, then you would need to find why this timeout happens.
>
> There are two probabilities:
>
> 1)	A cabling problem
>
> 2)	This is PATA and you have a hard disk at the same cable.
>
> In case of 1), check or replace the cables, make sure that the OS is set up for
> UDMA to the drive (this requires a 80 wire cable - unfortunately the drive 
> manufacturers deliver only 40 wire cable).
>
> In case of 2) use the -immed option.
>
> Jörg
>   

No, it's IDE with simulated SCSI on top of it. All hard drives are on SATA.
I replaced the cable and made sure it sits in tightly.

And still get the same error. The same DVD-witer orked fine on older 
motherboard with the older CPU.
Now when I moved in into the newer P6T-based system I get this error.

Yuri





[root at eagle /yuri-huge/movies/will-ackerman-new-age]# cdrecord dev=5,0,0 
speed=4 -v -dao -pad -useinfo -text *.wav
Cdrecord-ProDVD-ProBD-Clone 2.01.01a62 (i386-unknown-freebsd7.2) 
Copyright (C) 1995-2009 J�rg Schilling
TOC Type: 0 = CD-DA
scsidev: '5,0,0'
scsibus: 5 target: 0 lun: 0
Using libscg version 'schily-0.9'.
SCSI buffer size: 65536
atapi: 0
Device type : Removable CD-ROM
Version : 0
Response Format: 2
Capabilities :
Vendor_info : 'PIONEER '
Identifikation : 'DVD-RW DVR-112D'
Revision : '1.21'
Device seems to be: Generic mmc2 DVD-R/DVD-RW/DVD-RAM.
Current: CD-R
Profile: DVD+R/DL
Profile: DVD+R
Profile: DVD+RW
Profile: DVD-R/DL layer jump recording
Profile: DVD-R/DL sequential recording
Profile: DVD-RW sequential recording
Profile: DVD-RW restricted overwrite
Profile: DVD-R sequential recording
Profile: DVD-ROM
Profile: CD-RW
Profile: CD-R (current)
Profile: CD-ROM
Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
Driver flags : MMC-3 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P 
RAW/R96R LAYER_JUMP
Drive buf size : 1267712 = 1238 KB
cdrecord: Warning: The DMA speed test has been skipped.
FIFO size : 4194304 = 4096 KB
pregap1: -1
Track 01: audio 54 MB (05:24.16) no preemp
Track 02: audio 41 MB (04:05.64) no preemp pregapsize: 395
Track 03: audio 56 MB (05:38.76) no preemp pregapsize: 388
Track 04: audio 67 MB (06:42.04) no preemp pregapsize: 425
Track 05: audio 29 MB (02:56.33) no preemp pregapsize: 500
Track 06: audio 84 MB (08:19.46) no preemp pregapsize: 518
Track 07: audio 57 MB (05:39.86) no preemp pregapsize: 380
Track 08: audio 32 MB (03:11.06) no preemp pregapsize: 578
Track 09: audio 40 MB (03:59.80) no preemp pregapsize: 340
Track 10: audio 95 MB (09:27.22) no preemp pregapsize: 305
Track 11: audio 27 MB (02:41.44) no preemp pregapsize: 332
Total size: 586 MB (58:05.80) = 261435 sectors
Lout start: 586 MB (58:07/60) = 261435 sectors
Current Secsize: 2048
ATIP info from disk:
Indicated writing power: 5
Disk Is not unrestricted
Disk Is not erasable
Disk sub type: Medium Type B, low Beta category (B-) (4)
ATIP start of lead in: -11834 (97:24/16)
ATIP start of lead out: 359849 (79:59/74)
Disk type: Short strategy type (Phthalocyanine or similar)
Manuf. index: 24
Manufacturer: SONY Corporation

Capacity Blklen/Sparesz. Format-type Type
0 2048 0x00 Unformated or Blank Media
Blocks total: 359849 Blocks current: 359849 Blocks remaining: 98414
Starting to write CD/DVD/BD at speed 4 in real SAO mode for single session.
Last chance to quit, starting real write 0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
BURN-Free is ON.
Turning BURN-Free off
Performing OPC...
Sending CUE sheet...
SAO startsec: -11834
Writing lead-in...
Lead-in write time: 48.669s
Writing pregap for track 1 at -150
cdrecord: faio_wait_on_buffer for writer timed out.
cdrecord: Input/output error. write_g1: scsi sendcmd: cmd timeout after 
206.051 (200) s
CDB: 2A 00 FF FF FF 6A 00 00 1B 00
cmd finished after 206.051s timeout 200s
write track pad data: error after 0 bytes
BFree: 1146 K BSize: 1152 K
Starting new track at sector: 0
Track 01: 0 of 54 MB written.cdrecord: Input/output error. write_g1: 
scsi sendcmd: cmd timeout after 207.017 (200) s
CDB: 2A 00 00 00 00 00 00 00 1B 00
cmd finished after 207.017s timeout 200s

write track data: error after 0 bytes
cdrecord: A write error occured.
cdrecord: Please properly read the error message above.
cdrecord: Input/output error. prevent/allow medium removal: scsi 
sendcmd: retryable error
CDB: 1E 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 06 00 00 00 00 0E 00 00 00 00 29 00 00 00 00 00 00 00 
00 00 00 00 00 00 00 00 00 00 00 00
Sense Key: 0x6 Unit Attention, Segment 0
Sense Code: 0x29 Qual 0x00 (power on, reset, or bus device reset 
occurred) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 212.061s timeout 200s
Writing time: 471.843s
Average write speed 8.2x.
Fixating...
Fixating time: 6.379s
cdrecord: fifo had 64 puts and 1 gets.
cdrecord: fifo was 0 times empty and 0 times full, min fill was 100%.