Problem with FreeBSD and external storage

Miguel Angelo miguellangelorj at yahoo.com.br
Mon Sep 17 15:18:49 PDT 2007 

Hi,
   
  I'm trying to put external disks(storage) in my FreeBSD server, but, i only can't see the disks that was allocated.
  I think that is necessary sometype of confugurations, because the hba was installed and all procedures necessary too.
   
  For information.
   
  Connection type --> SAN with switch MACdata and EMC storage.
  Note: I can see the storage array in dmesg.(see example above).
   
  I would like so much if somewhere can help.
   
  thank's for all.
   
  ******************************************************************************************
   
    # dmesg
  Copyright (c) 1992-2007 The FreeBSD Project.
  Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
          The Regents of the University of California. All rights reserved.
  FreeBSD is a registered trademark of The FreeBSD Foundation.
  FreeBSD 6.2-RELEASE #0: Thu May 31 10:58:03 UTC 2007
      root@:/usr/obj/usr/src/sys/LAB
  MPTable: <  Kings Canyon>
  Timecounter "i8254" frequency 1193182 Hz quality 0
  CPU: Intel(R) Xeon(TM) CPU 2.40GHz (2400.10-MHz 686-class CPU)
    Origin = "GenuineIntel"  Id = 0xf27  Stepping = 7
    Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
    Features2=0x4400<CNTX-ID,<b14>>
    Logical CPUs per core: 2
  real memory  = 2146959360 (2047 MB)
  avail memory = 2095882240 (1998 MB)
  FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
   cpu0 (BSP): APIC ID:  0
   cpu1 (AP): APIC ID:  1
   cpu2 (AP): APIC ID:  6
   cpu3 (AP): APIC ID:  7
  ioapic0: Assuming intbase of 0
  ioapic1: Assuming intbase of 24
  ioapic2: Assuming intbase of 48
  ioapic0 <Version 2.0> irqs 0-23 on motherboard
  ioapic1 <Version 2.0> irqs 24-47 on motherboard
  ioapic2 <Version 2.0> irqs 48-71 on motherboard
  kbd1 at kbdmux0
  cpu0 on motherboard
  cpu1 on motherboard
  cpu2 on motherboard
  cpu3 on motherboard
  pcib0: <MPTable Host-PCI bridge> pcibus 0 on motherboard
  pci0: <PCI bus> on pcib0
  pci0: <unknown> at device 0.1 (no driver attached)
  pcib1: <PCI-PCI bridge> at device 2.0 on pci0
  pci1: <PCI bus> on pcib1
  pci1: <base peripheral, interrupt controller> at device 28.0 (no driver attached)
  pcib2: <MPTable PCI-PCI bridge> at device 29.0 on pci1
  pci2: <PCI bus> on pcib2
  mpt0: <LSILogic 1030 Ultra4 Adapter> port 0x3000-0x30ff mem 0xfc220000-0xfc23ffff,0xfc200000-0xfc21ffff irq 48 at device 1.0 on pci2
  mpt0: [GIANT-LOCKED]
  mpt0: MPI Version=1.2.14.0
  em0: <Intel(R) PRO/1000 Network Connection Version - 6.2.9> port 0x3400-0x343f mem 0xfc240000-0xfc25ffff irq 54 at device 3.0 on pci2
  em0: Ethernet address: 00:30:48:25:6b:ca
  pci1: <base peripheral, interrupt controller> at device 30.0 (no driver attached)
  pcib3: <MPTable PCI-PCI bridge> at device 31.0 on pci1
  pci3: <PCI bus> on pcib3
  ahd0: <Adaptec AIC7902 Ultra320 SCSI adapter> port 0x4400-0x44ff,0x4000-0x40ff mem 0xfc300000-0xfc301fff irq 32 at device 2.0 on pci3
  ahd0: [GIANT-LOCKED]
  aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 101-133Mhz, 512 SCBs
  ahd1: <Adaptec AIC7902 Ultra320 SCSI adapter> port 0x4c00-0x4cff,0x4800-0x48ff mem 0xfc302000-0xfc303fff irq 33 at device 2.1 on pci3
  ahd1: [GIANT-LOCKED]
  aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI-X 101-133Mhz, 512 SCBs
  isp0: <Qlogic ISP 2312 PCI FC-AL Adapter> port 0x5000-0x50ff mem 0xfc304000-0xfc304fff irq 28 at device 3.0 on pci3
  isp0: set PCI line size to 16
  isp0: [GIANT-LOCKED]
  isp0: Board Type 2312, Chip Revision 0x2, resident F/W Revision 3.3.19
  isp0: 839 max I/O commands supported
  isp0: NVRAM Port WWN 0x210000e08b9a13ea
  pci0: <serial bus, USB> at device 29.0 (no driver attached)
  pci0: <serial bus, USB> at device 29.1 (no driver attached)
  pci0: <serial bus, USB> at device 29.2 (no driver attached)
  pcib4: <MPTable PCI-PCI bridge> at device 30.0 on pci0
  pci4: <PCI bus> on pcib4
  atapci0: <HighPoint HPT374 (channel 0+1) UDMA133 controller> port 0x6c50-0x6c57,0x6c44-0x6c47,0x6c48-0x6c4f,0x6c40-0x6c43,0x6000-0x60ff irq 16 at device 1.0 on pci4
  ata2: <ATA channel 0> on atapci0
  ata3: <ATA channel 1> on atapci0
  atapci1: <HighPoint HPT374 (channel 2+3) UDMA133 controller> port 0x6c68-0x6c6f,0x6c5c-0x6c5f,0x6c60-0x6c67,0x6c58-0x6c5b,0x6400-0x64ff irq 16 at device 1.1 on pci4
  ata4: <ATA channel 0> on atapci1
  ata5: <ATA channel 1> on atapci1
  pci4: <display, VGA> at device 4.0 (no driver attached)
  fxp0: <Intel 82551 Pro/100 Ethernet> port 0x6c00-0x6c3f mem 0xfc401000-0xfc401fff,0xfc420000-0xfc43ffff irq 22 at device 5.0 on pci4
  miibus0: <MII bus> on fxp0
  inphy0: <i82555 10/100 media interface> on miibus0
  inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
  fxp0: Ethernet address: 00:30:48:25:6b:cb
  isab0: <PCI-ISA bridge> at device 31.0 on pci0
  isa0: <ISA bus> on isab0
  atapci2: <Intel ICH3 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x2060-0x206f at device 31.1 on pci0
  ata0: <ATA channel 0> on atapci2
  ata1: <ATA channel 1> on atapci2
  pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
  pmtimer0 on isa0
  orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc8fff,0xc9000-0xc97ff,0xc9800-0xcd7ff,0xe0000-0xe3fff on isa0
  atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
  atkbd0: <AT Keyboard> irq 1 on atkbdc0
  kbd0 at atkbd0
  atkbd0: [GIANT-LOCKED]
  sc0: <System console> at flags 0x100 on isa0
  sc0: VGA <16 virtual consoles, flags=0x300>
  sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
  sio0: type 16550A
  sio1 at port 0x2f8-0x2ff irq 3 on isa0
  sio1: type 16550A
  vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
  unknown: <PNP0c02> can't assign resources (memory)
  unknown: <PNP0303> can't assign resources (port)
  unknown: <PNP0c02> can't assign resources (memory)
  unknown: <PNP0501> can't assign resources (port)
  unknown: <PNP0501> can't assign resources (port)
  Timecounters tick every 1.000 msec
  isp0: Loop Reset Received
  isp0: Loop Reset Received
  isp0: LIP Received
  isp0: Point-to-Point mode
  isp0: Loop UP
  isp0: Port Database Changed
  isp0: Firmware State <Config Wait->Ready>
  isp0: Target 126 (Loop 0x7e) Port ID 0xfffffe (role (none)) Arrived
   Port WWN 0x200d080088037938
   Node WWN 0x1000080088037938
  isp0: 2Gb link speed/s
  isp0: Loop ID 255, Port ID 0x610d13, Loop State 0x2, Topology 'F Port'
  isp0: Target 255 (Loop 0xff) Port ID 0x610d13 (role Initiator) Arrived
   Port WWN 0x210000e08b9a13ea
   Node WWN 0x200000e08b9a13ea
  isp0:   Fabric Device @ PortID 0x610413
  isp0:   Fabric Device @ PortID 0x610d13
  isp0: Target 0 (Loop 0x0) Port ID 0x610413 (role Target) Arrived
   Port WWN 0x5006048c4a859540
   Node WWN 0x5006048c4a859540
  acd0: CDROM <LTN526S/YS0J> at ata0-master UDMA33
  ad4: 76319MB <Seagate ST380011A 3.06> at ata2-master UDMA100
  ad6: 76319MB <Seagate ST380011A 3.06> at ata3-master UDMA100
  ad9: 381554MB <Seagate ST3400832A 3.03> at ata4-slave UDMA100
  ad11: 381554MB <Seagate ST3400832A 3.03> at ata5-slave UDMA100
  Waiting 5 seconds for SCSI devices to settle
  pass0 at isp0 bus 0 target 0 lun 0
  pass0: <EMC SYMMETRIX 5670> Fixed Storage Array SCSI-2 device
  pass0: 200.000MB/s transfers, Tagged Queueing Enabled
  ar0: 76319MB <HighPoint v3 RocketRAID RAID1> status: READY
  ar0: disk0 READY (master) using ad4 at ata2-master
  ar0: disk1 READY (mirror) using ad6 at ata3-master
  ar1: 381554MB <HighPoint v3 RocketRAID RAID1> status: READY
  ar1: disk0 READY (master) using ad9 at ata4-slave
  ar1: disk1 READY (mirror) using ad11 at ata5-slave
  SMP: AP CPU #1 Launched!
  SMP: AP CPU #3 Launched!
  SMP: AP CPU #2 Launched!
  Trying to mount root from ufs:/dev/ar0s1a
  uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port 0x2000-0x201f irq 16 at device 29.0 on pci0
  uhci0: [GIANT-LOCKED]
  usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0
  usb0: USB revision 1.0
  uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
  uhub0: 2 ports with 2 removable, self powered
  uhci1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> port 0x2020-0x203f irq 19 at device 29.1 on pci0
  uhci1: [GIANT-LOCKED]
  usb1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> on uhci1
  usb1: USB revision 1.0
  uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
  uhub1: 2 ports with 2 removable, self powered
  uhci2: <Intel 82801CA/CAM (ICH3) USB controller USB-C> port 0x2040-0x205f irq 18 at device 29.2 on pci0
  uhci2: [GIANT-LOCKED]
  usb2: <Intel 82801CA/CAM (ICH3) USB controller USB-C> on uhci2
  usb2: USB revision 1.0
  uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
  uhub2: 2 ports with 2 removable, self powered
  #
   
  ****************************************************************************************



Sds,
Miguel Angelo
       Flickr agora em português. Você clica, todo mundo vê. Saiba mais.

More information about the freebsd-questions mailing list