nvidia-driver rebooting machine on X startup
Derek Ragona
derek at computinginnovations.com
Thu Sep 6 15:08:42 PDT 2007
At 03:10 PM 9/6/2007, Darren Spruell wrote:
>Wondering if this is a known issue, or if anyone has suggestions to
>get it working...?
>
>Running FreeBSD 6.2-RELEASE-p4 SMP i386.
>
>I installed nvidia-driver-100.14.11 from ports (Sep. 5 snapshot),
>Linux compatibility enabled. After loading modules 'linux' and
>'nvidia', I do:
>
># X -configure
># X -config /root/xorg.conf.new
>
>At this point the system spontaneously reboots. 'X -configure' runs
>fine and produces a configuration without issue, but the reboot
>occcurs when launching X. Nothing is output to screen (it flickers as
>if starting X), and nothing is written to /var/log/Xorg.0.log. I do
>get the same behavior if running 'xorgcfg'.
>
>Card info:
>
>"NV41 [Quadro FX 3450/4000 SDI] rev 162"
>
>nvidia0 at pci7:0:0: class=0x030000 card=0x029b10de chip=0x00cd10de
>rev=0xa2 hdr=0x00
> vendor = 'NVIDIA Corporation'
> class = display
> subclass = VGA
>
>I've tried an alternate version of the binary driver
>(nvidia-driver-96xx) to see if there was any change, and it also
>reboots on X startup.
>
>sysctl.conf, dmesg, and Xorg configuration included below.
>
>sysctl.conf:
>
># Recommended settings from xine package:
>kern.ipc.shmmax=67108864
>kern.ipc.shmall=32768
># Local settings
>vfs.usermount=1
>
>/var/run/dmesg.boot
>
>Copyright (c) 1992-2007 The FreeBSD Project.
>Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> The Regents of the University of California. All rights reserved.
>FreeBSD is a registered trademark of The FreeBSD Foundation.
>FreeBSD 6.2-RELEASE-p4 #0: Thu Apr 26 17:55:55 UTC 2007
> root at i386-builder.daemonology.net:/usr/obj/usr/src/sys/SMP
>acpi_alloc_wakeup_handler: can't alloc wake memory
>Timecounter "i8254" frequency 1193182 Hz quality 0
>CPU: Intel(R) Xeon(R) CPU E5345 @ 2.33GHz (2327.51-MHz
>686-class CPU)
> Origin = "GenuineIntel" Id = 0x6f7 Stepping = 7
>
>Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
>
>Features2=0x4e3bd<SSE3,RSVD2,MON,DS_CPL,VMX,EST,TM2,<b9>,CX16,<b14>,<b15>,<b18>>
> AMD Features=0x20100000<NX,LM>
> AMD Features2=0x1<LAHF>
> Cores per package: 4
>real memory = 3219169280 (3070 MB)
>avail memory = 3140694016 (2995 MB)
>ACPI APIC Table: <DELL B8K >
>FreeBSD/SMP: Multiprocessor System Detected: 8 CPUs
> cpu0 (BSP): APIC ID: 0
> cpu1 (AP): APIC ID: 1
> cpu2 (AP): APIC ID: 2
> cpu3 (AP): APIC ID: 3
> cpu4 (AP): APIC ID: 4
> cpu5 (AP): APIC ID: 5
> cpu6 (AP): APIC ID: 6
> cpu7 (AP): APIC ID: 7
>ioapic0: Changing APIC ID to 8
>ioapic1: Changing APIC ID to 9
>ioapic0 <Version 2.0> irqs 0-23 on motherboard
>ioapic1 <Version 2.0> irqs 24-47 on motherboard
>kbd1 at kbdmux0
>netsmb_dev: loaded
>ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
>acpi0: <DELL B8K > on motherboard
>acpi0: Power Button (fixed)
>Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
>acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
>cpu0: <ACPI CPU> on acpi0
>cpu1: <ACPI CPU> on acpi0
>cpu2: <ACPI CPU> on acpi0
>cpu3: <ACPI CPU> on acpi0
>cpu4: <ACPI CPU> on acpi0
>cpu5: <ACPI CPU> on acpi0
>cpu6: <ACPI CPU> on acpi0
>cpu7: <ACPI CPU> on acpi0
>acpi_button0: <Power Button> on acpi0
>pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
>pci0: <ACPI PCI bus> on pcib0
>pcib1: <ACPI PCI-PCI bridge> at device 2.0 on pci0
>pci1: <ACPI PCI bus> on pcib1
>pcib2: <ACPI PCI-PCI bridge> irq 16 at device 0.0 on pci1
>pci2: <ACPI PCI bus> on pcib2
>pcib3: <ACPI PCI-PCI bridge> irq 16 at device 0.0 on pci2
>pci3: <ACPI PCI bus> on pcib3
>pcib4: <PCI-PCI bridge> irq 16 at device 1.0 on pci2
>pci4: <PCI bus> on pcib4
>pcib5: <ACPI PCI-PCI bridge> at device 0.3 on pci1
>pci5: <ACPI PCI bus> on pcib5
>fwohci0: <Lucent FW322/323> mem 0xdceff000-0xdcefffff irq 26 at device
>5.0 on pci5
>fwohci0: OHCI version 1.0 (ROM=1)
>fwohci0: No. of Isochronous channels is 8.
>fwohci0: EUI64 00:00:d1:00:80:35:7a:57
>fwohci0: Phy 1394a available S400, 3 ports.
>fwohci0: Link S400, max_rec 2048 bytes.
>firewire0: <IEEE1394(FireWire) bus> on fwohci0
>fwe0: <Ethernet over FireWire> on firewire0
>if_fwe0: Fake Ethernet address: 02:00:d1:35:7a:57
>fwe0: Ethernet address: 02:00:d1:35:7a:57
>fwe0: if_start running deferred for Giant
>sbp0: <SBP-2/SCSI over FireWire> on firewire0
>fwohci0: Initiate bus reset
>fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
>firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
>firewire0: bus manager 0 (me)
>pcib6: <ACPI PCI-PCI bridge> at device 3.0 on pci0
>pci6: <ACPI PCI bus> on pcib6
>pcib7: <ACPI PCI-PCI bridge> at device 4.0 on pci0
>pci7: <ACPI PCI bus> on pcib7
>nvidia0: <Quadro FX 3450/4000 SDI> mem
>0xdd000000-0xddffffff,0xc0000000-0xcfffffff,0xde000000-0xdeffffff irq
>16 at device 0.0 on pci7
>nvidia0: [GIANT-LOCKED]
>pcib8: <ACPI PCI-PCI bridge> at device 5.0 on pci0
>pci8: <ACPI PCI bus> on pcib8
>pcib9: <ACPI PCI-PCI bridge> at device 6.0 on pci0
>pci9: <ACPI PCI bus> on pcib9
>pcib10: <ACPI PCI-PCI bridge> at device 7.0 on pci0
>pci10: <ACPI PCI bus> on pcib10
>pci0: <multimedia> at device 27.0 (no driver attached)
>pcib11: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
>pci11: <ACPI PCI bus> on pcib11
>bge0: <Broadcom BCM5752 A2, ASIC rev. 0x6002> mem
>0xdccf0000-0xdccfffff irq 16 at device 0.0 on pci11
>bge0: firmware handshake timed out
>miibus0: <MII bus> on bge0
>brgphy0: <BCM5752 10/100/1000baseTX PHY> on miibus0
>brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
>1000baseTX-FDX, auto
>bge0: Ethernet address: 00:1a:a0:ac:eb:69
>uhci0: <UHCI (generic) USB controller> port 0xff80-0xff9f irq 21 at
>device 29.0 on pci0
>uhci0: [GIANT-LOCKED]
>usb0: <UHCI (generic) USB controller> on uhci0
>usb0: USB revision 1.0
>uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
>uhub0: 2 ports with 2 removable, self powered
>uhci1: <UHCI (generic) USB controller> port 0xff60-0xff7f irq 22 at
>device 29.1 on pci0
>uhci1: [GIANT-LOCKED]
>usb1: <UHCI (generic) USB controller> on uhci1
>usb1: USB revision 1.0
>uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
>uhub1: 2 ports with 2 removable, self powered
>uhci2: <UHCI (generic) USB controller> port 0xff40-0xff5f irq 18 at
>device 29.2 on pci0
>uhci2: [GIANT-LOCKED]
>usb2: <UHCI (generic) USB controller> on uhci2
>usb2: USB revision 1.0
>uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
>uhub2: 2 ports with 2 removable, self powered
>uhci3: <UHCI (generic) USB controller> port 0xff20-0xff3f irq 23 at
>device 29.3 on pci0
>uhci3: [GIANT-LOCKED]
>usb3: <UHCI (generic) USB controller> on uhci3
>usb3: USB revision 1.0
>uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
>uhub3: 2 ports with 2 removable, self powered
>ehci0: <EHCI (generic) USB 2.0 controller> mem 0xff980800-0xff980bff
>irq 21 at device 29.7 on pci0
>ehci0: [GIANT-LOCKED]
>usb4: waiting for BIOS to give up control
>usb4: EHCI version 1.0
>usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3
>usb4: <EHCI (generic) USB 2.0 controller> on ehci0
>usb4: USB revision 2.0
>uhub4: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
>uhub4: 8 ports with 8 removable, self powered
>uhub5: NEC Corporation USB2.0 Hub Controller, class 9/0, rev 2.00/1.00, addr 2
>uhub5: single transaction translator
>uhub5: 4 ports with 4 removable, self powered
>pcib12: <ACPI PCI-PCI bridge> at device 30.0 on pci0
>pci12: <ACPI PCI bus> on pcib12
>isab0: <PCI-ISA bridge> at device 31.0 on pci0
>isa0: <ISA bus> on isab0
>atapci0: <Intel 63XXESB2 UDMA100 controller> port
>0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf irq 16 at device
>31.1 on pci0
>ata0: <ATA channel 0> on atapci0
>ata1: <ATA channel 1> on atapci0
>atapci1: <Intel 63XXESB2 SATA300 controller> port
>0xfe00-0xfe07,0xfe10-0xfe13,0xfe20-0xfe27,0xfe30-0xfe33,0xfec0-0xfedf
>mem 0xff970000-0xff9703ff irq 20 at device 31.2 on pci0
>atapci1: AHCI Version 01.10 controller with 6 ports detected
>ata2: <ATA channel 0> on atapci1
>ata3: <ATA channel 1> on atapci1
>ata4: <ATA channel 2> on atapci1
>ata5: <ATA channel 3> on atapci1
>ata6: <ATA channel 4> on atapci1
>ata7: <ATA channel 5> on atapci1
>pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
>fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
>fdc0: [FAST]
>fd0: <1440-KB 3.5" drive> on fdc0 drive 0
>ppc0: <ECP parallel printer port> port 0x378-0x37f,0x778-0x77f irq 7 on acpi0
>ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
>ppc0: FIFO with 16/16/8 bytes threshold
>ppbus0: <Parallel port bus> on ppc0
>plip0: <PLIP network interface> on ppbus0
>lpt0: <Printer> on ppbus0
>lpt0: Interrupt-driven port
>ppi0: <Parallel I/O> on ppbus0
>sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
>sio0: type 16550A
>sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
>sio1: type 16550A
>pmtimer0 on isa0
>orm0: <ISA Option ROMs> at iomem
>0xc0000-0xcbfff,0xcc000-0xcdfff,0xce000-0xd2fff,0xd3000-0xd3fff on
>isa0
>atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
>atkbd0: <AT Keyboard> irq 1 on atkbdc0
>kbd0 at atkbd0
>atkbd0: [GIANT-LOCKED]
>sc0: <System console> at flags 0x100 on isa0
>sc0: VGA <16 virtual consoles, flags=0x300>
>vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
>uhub6: Dell Dell USB Keyboard Hub, class 9/0, rev 1.10/48.01, addr 2
>uhub6: 3 ports with 2 removable, bus powered
>ukbd0: Dell Dell USB Keyboard Hub, rev 1.10/48.00, addr 3, iclass 3/1
>kbd2 at ukbd0
>uhid0: Dell Dell USB Keyboard Hub, rev 1.10/48.00, addr 3, iclass 3/1
>ums0: vendor 0x0461 USB Optical Mouse, rev 2.00/2.00, addr 4, iclass 3/1
>ums0: 3 buttons and Z dir.
>Timecounters tick every 1.000 msec
>acd0: DVDR <PHILIPS DVD+/-RW DVD8801/AD21> at ata0-master UDMA33
>ad4: 152587MB <WDC WD1600ADFS-75SLR2 21.07Q21> at ata2-master SATA300
>ad6: 152587MB <WDC WD1600ADFS-75SLR2 21.07Q21> at ata3-master SATA300
>ar0: 152585MB <Intel MatrixRAID RAID1> status: READY
>ar0: disk0 READY (master) using ad4 at ata2-master
>ar0: disk1 READY (mirror) using ad6 at ata3-master
>SMP: AP CPU #3 Launched!
>SMP: AP CPU #1 Launched!
>SMP: AP CPU #6 Launched!
>SMP: AP CPU #2 Launched!
>SMP: AP CPU #7 Launched!
>SMP: AP CPU #4 Launched!
>SMP: AP CPU #5 Launched!
>Trying to mount root from ufs:/dev/ar0s1a
>WARNING: / was not properly dismounted
>WARNING: /tmp was not properly dismounted
>/tmp: mount pending error: blocks 0 files 1
>WARNING: /usr was not properly dismounted
>WARNING: /var was not properly dismounted
>bge0: firmware handshake timed out
>
>xorg.conf.new
>
>Section "ServerLayout"
> Identifier "X.org Configured"
> Screen 0 "Screen0" 0 0
> InputDevice "Mouse0" "CorePointer"
> InputDevice "Keyboard0" "CoreKeyboard"
>EndSection
>
>Section "Files"
> RgbPath "/usr/local/share/X11/rgb"
> ModulePath "/usr/local/lib/xorg/modules"
> FontPath "/usr/local/lib/X11/fonts/misc/"
> FontPath "/usr/local/lib/X11/fonts/TTF/"
> FontPath "/usr/local/lib/X11/fonts/OTF"
> FontPath "/usr/local/lib/X11/fonts/Type1/"
> FontPath "/usr/local/lib/X11/fonts/100dpi/"
> FontPath "/usr/local/lib/X11/fonts/75dpi/"
>EndSection
>
>Section "Module"
> Load "dbe"
> Load "dri"
> Load "extmod"
> Load "record"
> Load "xtrap"
> Load "glx"
> Load "freetype"
> Load "type1"
>EndSection
>
>Section "InputDevice"
> Identifier "Keyboard0"
> Driver "kbd"
>EndSection
>
>Section "InputDevice"
> Identifier "Mouse0"
> Driver "mouse"
> Option "Protocol" "auto"
> Option "Device" "/dev/sysmouse"
> Option "ZAxisMapping" "4 5 6 7"
>EndSection
>
>Section "Monitor"
> Identifier "Monitor0"
> VendorName "Monitor Vendor"
> ModelName "Monitor Model"
>EndSection
>
>Section "Device"
> Identifier "Card0"
> Driver "nvidia"
> VendorName "nVidia Corporation"
> BoardName "NV41 [Quadro FX 3450/4000 SDI]"
> BusID "PCI:7:0:0"
>EndSection
>
>Section "Screen"
> Identifier "Screen0"
> Device "Card0"
> Monitor "Monitor0"
> SubSection "Display"
> Viewport 0 0
> Depth 1
> EndSubSection
> SubSection "Display"
> Viewport 0 0
> Depth 4
> EndSubSection
> SubSection "Display"
> Viewport 0 0
> Depth 8
> EndSubSection
> SubSection "Display"
> Viewport 0 0
> Depth 15
> EndSubSection
> SubSection "Display"
> Viewport 0 0
> Depth 16
> EndSubSection
> SubSection "Display"
> Viewport 0 0
> Depth 24
> EndSubSection
>EndSection
>
>--
Check your AGP settings and consult the readme, chapter 9, for the latest
driver. You should be running the latest driver with your card.
Make sure you have the correct AGP settings, either letting FreeBSD do it
in the kernel or disable the kernel and let the Nvidia driver manage it.
-Derek
--
This message has been scanned for viruses and
dangerous content by MailScanner, and is
believed to be clean.
MailScanner thanks transtec Computers for their support.
More information about the freebsd-questions
mailing list