PPPoE config FreeBSD. Need help

[Boris Samorodov]

On Sat, 20 Oct 2007 10:00:27 +0500 Babek Ismayilov wrote:

> i need to configure PPPoE in FreeBSD 6.2.

> I tested but it didn't work out. I'm want to show you the result of the
> command:

> web# ppp
> Working in interactive mode
> Using interface: tun0
> ppp ON web> dial Internet
> ppp ON web> ping box.az
> Warning: ping: Invalid command
> Warning: ping: Failed 1
> ppp ON web>
> ppp ON web> pppd
> Warning: pppd: Invalid command
> Warning: pppd: Failed 1
> ppp ON web> quit
> web# pppd

There is a very good diagnostic file /var/log/ppp.log . You may
populate it by the needed info. (Hint: man ppp)

> Here is rc.conf


> rc.conf


> # -- sysinstall generated deltas -- # Fri Oct 19 16:25:38 2007
> # Created: Fri Oct 19 16:25:38 2007
> # Enable network daemons for user convenience.
> # Please make all changes to this file, not to /etc/defaults/rc.conf.
> # This file now contains just the overrides from /etc/defaults/rc.conf.
> #defaultrouter="172.16.200.1"
> hostname="web.pronet"
> ifconfig_rl0="inet 172.16.200.201 netmask 255.255.255.0"
> inetd_enable="YES"
> linux_enable="YES"
> sshd_enable="YES"
> usbd_enable="YES"
> ppp_interface="rl1"
> ppp_enable="YES"
> ppp_mode="ddial"
> ppp_nat="NO"
> ppp_profile="primus"
> network_interfaces="rl1 lo0"
> ifconfig_rl1="inet 10.0.0.1 netmask 255.255.255.0"

Where did you get info for rl0, rl1 interface?
Why did you disable rl0 interface with "network_interfaces="?
(Hint: there is no need for _PPPoE_ in any those ip-addresses)

> ppp.conf

Is it a copy-n-paste problem that you don't have a space before
commands? I.e.:
-----
default:
 set log Phase Chat LCP IPCP CCP tun command
-----

> #################################################################
> # PPP Sample Configuration File
> # Originally written by Toshiharu OHNO
> # Simplified 5/14/1999 by wself at cdrom.com
> #
> # See /usr/share/examples/ppp/ for some examples
> #
> # $FreeBSD: src/etc/ppp/ppp.conf,v 1.10 2004/11/19 17:12:56 obrien Exp $
> #################################################################

> default:
> set log Phase Chat LCP IPCP CCP tun command
> ident user-ppp VERSION (built COMPILATIONDATE)

> # Ensure that "device" references the correct serial port
> # for your modem. (cuad0 = COM1, cuad1 = COM2)
> #
> set device PPPoE:rl1

> set speed 115200
> set dial "ABORT BUSY ABORT NO\\sCARRIER TIMEOUT 5 \
> \"\" AT OK-AT-OK ATE1Q0 OK \\dATDT\\T TIMEOUT 40 CONNECT"
> set timeout 180 # 3 minute idle timer (the default)
> enable dns # request DNS info (for resolv.conf)

> papchap:
> #
> # edit the next three lines and replace the items in caps with
> # the values which have been assigned by your ISP.
> #

> primus:

> set authname pronet
> set authkey 3060683

> set ifaddr 10.0.0.1/0 10.0.0.2/0 255.255.255.0 0.0.0.0
> add default HISADDR # Add a (sticky) default route


> added there lines to GENERIC:

The needed modules should have been loaded automagically.

> # Enables PPPoE
>   options NETGRAPH
>   options NETGRAPH_SOCKET
>   options NETGRAPH_PPPOE

> But still didnt work out.


> Please give some advice.

Please take a look at /usr/share/examples/ppp.conf.sample. There is a
good example. Just two labels and a some ten commands. Insert your
values and get your PPPoE.


HTH and WBR
-- 
bsam