MII without PHY problem with SBC card
Richard Smith
rdls at rdls.net
Wed Jun 20 12:52:45 UTC 2007
Dear all,
I have a ROCKY-3786EV-RS which is a PICMG single board computer. It has
an embedded NIC which is initially detected as fxp0, but then fails to
attach with an "MII without PHY" error.
Is this a fixable problem? Is this a bug? Is the LAN interface lost to me?
Verbose 'dmesg' up to the place of the error message follows:
Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-RELEASE #0: Fri Jan 12 10:40:27 UTC 2007
root at dessler.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0b52000.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0b52160.
Calibrating clock(s) ... i8254 clock: 1193156 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 996551401 Hz
CPU: Intel Pentium III (996.55-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x68a Stepping = 10
Features=0x387f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,PN,MMX,FXSR,SSE>
real memory = 267321344 (254 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000c25000 - 0x000000000fa32fff, 249618432 bytes (60942 pages)
avail memory = 252059648 (240 MB)
bios32: Found BIOS32 Service Directory header at 0xc00fae70
bios32: Entry = 0xfb2f0 (c00fb2f0) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0xb320
pnpbios: Found PnP BIOS data at 0xc00fbcd0
pnpbios: Entry = f0000:bd00 Rev = 1.0
Other BIOS signatures found:
wlan: <802.11 Link Layer>
ath_rate: version 1.2 <SampleRate bit-rate selection algorithm>
null: <null device, zero device>
random: <entropy source, Software, Yarrow>
nfslock: pseudo-device
io: <I/O>
kbd: new array size 4
kbd1 at kbdmux0
mem: <memory>
Pentium Pro MTRR support enabled
ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
rr232x: RocketRAID 232x controller driver v1.02 (Jan 12 2007 10:40:02)
npx0: INT 16 interface
acpi0: <IntelR AWRDACPI> on motherboard
acpi0: [MPSAFE]
pci_open(1): mode 1 addr port (0x0cf8) is 0x80000058
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=11308086)
pcibios: BIOS version 2.10
Found $PIR table, 15 entries at 0xc00fde60
PCI-Only Interrupts: 5 9 10 11 12
Location Bus Device Pin Link IRQs
slot 1 1 8 A 0x68 3 4 5 7 9 10 11 12 14 15
slot 1 1 8 B 0x69 3 4 5 7 9 10 11 12 14 15
slot 1 1 8 C 0x6a 3 4 5 7 9 10 11 12 14 15
slot 1 1 8 D 0x6b 3 4 5 7 9 10 11 12 14 15
slot 2 1 15 A 0x61 3 4 5 7 9 10 11 12 14 15
slot 2 1 15 B 0x62 3 4 5 7 9 10 11 12 14 15
slot 2 1 15 C 0x63 3 4 5 7 9 10 11 12 14 15
slot 2 1 15 D 0x60 3 4 5 7 9 10 11 12 14 15
slot 3 1 14 A 0x62 3 4 5 7 9 10 11 12 14 15
slot 3 1 14 B 0x63 3 4 5 7 9 10 11 12 14 15
slot 3 1 14 C 0x60 3 4 5 7 9 10 11 12 14 15
slot 3 1 14 D 0x61 3 4 5 7 9 10 11 12 14 15
slot 4 1 13 A 0x63 3 4 5 7 9 10 11 12 14 15
slot 4 1 13 B 0x60 3 4 5 7 9 10 11 12 14 15
slot 4 1 13 C 0x61 3 4 5 7 9 10 11 12 14 15
slot 4 1 13 D 0x62 3 4 5 7 9 10 11 12 14 15
slot 5 1 12 A 0x60 3 4 5 7 9 10 11 12 14 15
slot 5 1 12 B 0x61 3 4 5 7 9 10 11 12 14 15
slot 5 1 12 C 0x62 3 4 5 7 9 10 11 12 14 15
slot 5 1 12 D 0x63 3 4 5 7 9 10 11 12 14 15
slot 6 1 11 A 0x61 3 4 5 7 9 10 11 12 14 15
slot 6 1 11 B 0x62 3 4 5 7 9 10 11 12 14 15
slot 6 1 11 C 0x63 3 4 5 7 9 10 11 12 14 15
slot 6 1 11 D 0x60 3 4 5 7 9 10 11 12 14 15
slot 7 1 10 A 0x62 3 4 5 7 9 10 11 12 14 15
slot 7 1 10 B 0x63 3 4 5 7 9 10 11 12 14 15
slot 7 1 10 C 0x60 3 4 5 7 9 10 11 12 14 15
slot 7 1 10 D 0x61 3 4 5 7 9 10 11 12 14 15
slot 8 1 9 A 0x68 3 4 5 7 9 10 11 12 14 15
slot 8 1 9 B 0x69 3 4 5 7 9 10 11 12 14 15
slot 8 1 9 C 0x6a 3 4 5 7 9 10 11 12 14 15
slot 8 1 9 D 0x6b 3 4 5 7 9 10 11 12 14 15
slot 9 1 7 A 0x61 3 4 5 7 9 10 11 12 14 15
slot 9 1 7 B 0x62 3 4 5 7 9 10 11 12 14 15
slot 9 1 7 C 0x63 3 4 5 7 9 10 11 12 14 15
slot 9 1 7 D 0x60 3 4 5 7 9 10 11 12 14 15
slot 10 1 6 A 0x62 3 4 5 7 9 10 11 12 14 15
slot 10 1 6 B 0x63 3 4 5 7 9 10 11 12 14 15
slot 10 1 6 C 0x60 3 4 5 7 9 10 11 12 14 15
slot 10 1 6 D 0x61 3 4 5 7 9 10 11 12 14 15
slot 11 1 5 A 0x63 3 4 5 7 9 10 11 12 14 15
slot 11 1 5 B 0x62 3 4 5 7 9 10 11 12 14 15
slot 11 1 5 C 0x61 3 4 5 7 9 10 11 12 14 15
slot 11 1 5 D 0x60 3 4 5 7 9 10 11 12 14 15
slot 12 1 4 A 0x60 3 4 5 7 9 10 11 12 14 15
slot 12 1 4 B 0x61 3 4 5 7 9 10 11 12 14 15
slot 12 1 4 C 0x62 3 4 5 7 9 10 11 12 14 15
slot 12 1 4 D 0x63 3 4 5 7 9 10 11 12 14 15
slot 13 1 3 A 0x61 3 4 5 7 9 10 11 12 14 15
slot 13 1 3 B 0x62 3 4 5 7 9 10 11 12 14 15
slot 13 1 3 C 0x63 3 4 5 7 9 10 11 12 14 15
slot 13 1 3 D 0x60 3 4 5 7 9 10 11 12 14 15
embedded 0 31 A 0x60 3 4 5 7 9 10 11 12 14 15
embedded 0 31 B 0x61 3 4 5 7 9 10 11 12 14 15
embedded 0 31 C 0x6b 3 4 5 7 9 10 11 12 14 15
embedded 0 31 D 0x63 3 4 5 7 9 10 11 12 14 15
embedded 0 2 A 0x60 3 4 5 7 9 10 11 12 14 15
embedded 0 2 B 0x61 3 4 5 7 9 10 11 12 14 15
embedded 0 2 C 0x62 3 4 5 7 9 10 11 12 14 15
embedded 0 2 D 0x63 3 4 5 7 9 10 11 12 14 15
AcpiOsDerivePciId: bus 0 dev 31 func 0
AcpiOsDerivePciId: bus 0 dev 31 func 0
acpi0: Power Button (fixed)
acpi0: wakeup code va 0xc71c4000 pa 0x9e000
ACPI timer: 1/1 1/1 1/0 1/1 1/1 1/1 1/1 1/1 1/1 1/1 -> 10
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0
pci_link0: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 12 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link0: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 12 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link0: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link1: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 9 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link1: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 9 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link1: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link2: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 11 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link2: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 11 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link2: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link3: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 5 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link3: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 5 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link3: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link4: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 10 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link4: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 10 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link4: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link5: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link5: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link5: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link6: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link6: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link6: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link7: Links after initial probe:
Index IRQ Rtd Ref IRQs
0 11 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link7: Links after initial validation:
Index IRQ Rtd Ref IRQs
0 11 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link7: Links after disable:
Index IRQ Rtd Ref IRQs
0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
cpu0: <ACPI CPU> on acpi0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
acpi_throttle0: P_CNT from P_BLK 0x4010
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
ACPI: Found matching pin for 0.2.INTA at func 0: 12
ACPI: Found matching pin for 0.2.INTA at func 0: 12
ACPI: Found matching pin for 0.31.INTB at func 3: 9
ACPI: Found matching pin for 0.31.INTC at func 4: 11
ACPI: Found matching pin for 0.31.INTD at func 2: 5
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
found-> vendor=0x8086, dev=0x1130, revid=0x04
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x2090, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x1132, revid=0x04
bus=0, slot=2, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x02b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=12
powerspec 2 supports D0 D3 current D0
map[10]: type 3, range 32, base e0000000, size 26, enabled
map[14]: type 1, range 32, base e8000000, size 19, enabled
pcib0: matched entry for 0.2.INTA (src \\_SB_.PCI0.LNKA:0)
pcib0: slot 2 INTA routed to irq 12 via \\_SB_.PCI0.LNKA
found-> vendor=0x8086, dev=0x244e, revid=0x05
bus=0, slot=30, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x0080, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x06 (1500 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x2440, revid=0x05
bus=0, slot=31, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x000f, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x244b, revid=0x05
bus=0, slot=31, func=1
class=01-01-80, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[20]: type 4, range 32, base 0000f000, size 4, enabled
found-> vendor=0x8086, dev=0x2442, revid=0x05
bus=0, slot=31, func=2
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=d, irq=5
map[20]: type 4, range 32, base 0000d000, size 5, enabled
pcib0: matched entry for 0.31.INTD (src \\_SB_.PCI0.LNKD:0)
pcib0: slot 31 INTD routed to irq 5 via \\_SB_.PCI0.LNKD
found-> vendor=0x8086, dev=0x2443, revid=0x05
bus=0, slot=31, func=3
class=0c-05-00, hdrtype=0x00, mfdev=0
cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=9
map[20]: type 4, range 32, base 00005000, size 4, enabled
pcib0: matched entry for 0.31.INTB (src \\_SB_.PCI0.LNKB:0)
pcib0: slot 31 INTB routed to irq 9 via \\_SB_.PCI0.LNKB
found-> vendor=0x8086, dev=0x2444, revid=0x05
bus=0, slot=31, func=4
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=c, irq=11
map[20]: type 4, range 32, base 0000d800, size 5, enabled
pcib0: matched entry for 0.31.INTC (src \\_SB_.PCI0.LNK1:0)
pcib0: slot 31 INTC routed to irq 11 via \\_SB_.PCI0.LNK1
found-> vendor=0x8086, dev=0x2445, revid=0x05
bus=0, slot=31, func=5
class=04-01-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=9
map[10]: type 4, range 32, base 0000dc00, size 8, enabled
map[14]: type 4, range 32, base 0000e000, size 6, enabled
pcib0: matched entry for 0.31.INTB (src \\_SB_.PCI0.LNKB:0)
pcib0: slot 31 INTB routed to irq 9 via \\_SB_.PCI0.LNKB
agp0: <Intel 82815 (i815 GMCH) SVGA controller> mem
0xe0000000-0xe3ffffff,0xe8000000-0xe807ffff irq 12 at device 2.0 on pci0
agp0: Reserved 0x4000000 bytes for rid 0x10 type 3 at 0xe0000000
agp0: Reserved 0x80000 bytes for rid 0x14 type 3 at 0xe8000000
pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 2
pcib1: I/O decode 0xa000-0xcfff
pcib1: memory decode 0xe4000000-0xe7ffffff
pcib1: prefetched decode 0xfff00000-0xfffff
pcib1: Subtractively decoded bridge.
ACPI: Found matching pin for 1.8.INTA at func 0: 10
ACPI: Found matching pin for 1.14.INTA at func 0: 11
ACPI: Found matching pin for 1.9.INTA at func 0: 10
pci1: <ACPI PCI bus> on pcib1
pci1: physical bus=1
found-> vendor=0x8086, dev=0x2449, revid=0x03
bus=1, slot=8, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x38 (14000 ns)
intpin=a, irq=10
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base e7000000, size 12, enabled
pcib1: (null) requested memory range 0xe7000000-0xe7000fff: good
map[14]: type 4, range 32, base 0000c400, size 6, enabled
pcib1: (null) requested I/O range 0xc400-0xc43f: in range
pcib1: matched entry for 1.8.INTA (src \\_SB_.PCI0.LNKE:0)
pcib1: slot 8 INTA routed to irq 10 via \\_SB_.PCI0.LNKE
found-> vendor=0x10b9, dev=0x5281, revid=0xa4
bus=1, slot=9, func=0
class=01-80-85, hdrtype=0x00, mfdev=1
cmdreg=0x0005, statreg=0x02a0, cachelnsz=128 (dwords)
lattimer=0x80 (3840 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
map[10]: type 4, range 32, base 0000b000, size 3, enabled
pcib1: (null) requested I/O range 0xb000-0xb007: in range
map[14]: type 4, range 32, base 0000b400, size 2, enabled
pcib1: (null) requested I/O range 0xb400-0xb403: in range
map[18]: type 4, range 32, base 0000b800, size 3, enabled
pcib1: (null) requested I/O range 0xb800-0xb807: in range
map[1c]: type 4, range 32, base 0000bc00, size 2, enabled
pcib1: (null) requested I/O range 0xbc00-0xbc03: in range
map[20]: type 4, range 32, base 0000c000, size 4, enabled
pcib1: (null) requested I/O range 0xc000-0xc00f: in range
pcib1: matched entry for 1.9.INTA (src \\_SB_.PCI0.LNKE:0)
pcib1: slot 9 INTA routed to irq 10 via \\_SB_.PCI0.LNKE
found-> vendor=0x3388, dev=0x0022, revid=0x04
bus=1, slot=13, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x06 (1500 ns), maxlat=0x00 (0 ns)
found-> vendor=0x9005, dev=0x0080, revid=0x02
bus=1, slot=14, func=0
class=01-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x02b0, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x28 (10000 ns), maxlat=0x19 (6250 ns)
intpin=a, irq=11
powerspec 2 supports D0 D3 current D0
map[10]: type 4, range 32, base 0000c800, size 8, enabled
pcib1: (null) requested I/O range 0xc800-0xc8ff: in range
map[14]: type 1, range 64, base e7001000, size 12, enabled
pcib1: (null) requested memory range 0xe7001000-0xe7001fff: good
pcib1: matched entry for 1.14.INTA (src \\_SB_.PCI0.LNKC:0)
pcib1: slot 14 INTA routed to irq 11 via \\_SB_.PCI0.LNKC
fxp0: <Intel 82801BA/CAM (ICH2/3) Pro/100 Ethernet> port 0xc400-0xc43f
mem 0xe7000000-0xe7000fff irq 10 at device 8.0 on pci1
fxp0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xe7000000
fxp0: using memory space register mapping
fxp0: PCI IDs: 8086 2449 8086 3010 0003
fxp0: Dynamic Standby mode is disabled
fxp0: MII without any PHY!
device_attach: fxp0 attach returned 6
<snip>
Please 'cc' me with any suggestions/answers as I am not subscribed to
'questions'.
Regards,
Richard
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 249 bytes
Desc: OpenPGP digital signature
Url : http://lists.freebsd.org/pipermail/freebsd-questions/attachments/20070620/c102f575/signature.pgp
More information about the freebsd-questions
mailing list