External USB drive on Sun HW

[Aaron Burruss]

Anyone have any ideas here?

On 1/13/06, Aaron Burruss <aburruss at gmail.com> wrote:
>
> Hi there,
>
> I'm looking for some help on a problem I'm having with a new setup I've
> got... I'm running sparc64 6.0 and also have an external USB drive
> enclosure with a 250GB IDE drive in it.  The drive is formatted as a BSD
> partition (formatting done on another box).
>
> I've got the following in my kernel:
>
> # USB support
> device uhci # UHCI PCI->USB interface
> device ohci # OHCI PCI->USB interface
> device usb # USB Bus (required)
> device ugen # Generic
> device uhid # "Human Interface Devices"
> device umass # Disks/Mass storage - Requires scbus and da
>
> I.m seeing this in dmesg:
>
>
> root at sun# dmesg |grep -i umass
> umass0: vendor 0x05e3 USB TO IDE, rev 2.00/0.33, addr 2
> umass0: BBB reset failed, TIMEOUT
> umass0: BBB bulk-in clear stall failed, TIMEOUT
> umass0: BBB bulk-out clear stall failed, TIMEOUT
> umass0: BBB reset failed, TIMEOUT
> umass0: BBB bulk-in clear stall failed, TIMEOUT
> umass0: BBB bulk-out clear stall failed, TIMEOUT
> umass0: BBB reset failed, TIMEOUT
> umass0: BBB bulk-in clear stall failed, TIMEOUT
> umass0: BBB bulk-out clear stall failed, TIMEOUT
> umass0: BBB reset failed, TIMEOUT
> umass0: BBB bulk-in clear stall failed, TIMEOUT
> umass0: BBB bulk-out clear stall failed, TIMEOUT
> umass0: BBB reset failed, TIMEOUT
> umass0: BBB bulk-in clear stall failed, TIMEOUT
> umass0: BBB bulk-out clear stall failed, TIMEOUT
> root at sun# dmesg|grep -i usb
> ohci0: <Sun PCIO-2 USB controller> mem 0xe2000000-0xe2007fff at device
> 12.3 on pci1
> usb0: OHCI version 1.0, legacy support
> usb0: <Sun PCIO-2 USB controller> on ohci0
> usb0: USB revision 1.0
> ohci1: <Sun PCIO-2 USB controller> mem 0xe5000000-0xe5007fff at device 5.3on pci1
> usb1: OHCI version 1.0, legacy support
> usb1: <Sun PCIO-2 USB controller> on ohci1
> usb1: USB revision 1.0
> umass0: vendor 0x05e3 USB TO IDE, rev 2.00/0.33, addr 2
>


usbdevs shows:

root at sun# usbdevs -v
Controller /dev/usb0:
addr 1: full speed, self powered, config 1, OHCI root hub(0x0000),
(0x108e)(0x0000), rev 1.00
port 1 powered
port 2 powered
port 3 powered
port 4 powered
Controller /dev/usb1:
addr 1: full speed, self powered, config 1, OHCI root hub(0x0000),
(0x108e)(0x0000), rev 1.00
port 1 addr 2: full speed, self powered, config 1, product 0x0702(0x0702),
vendor 0x05e3(0x05e3), rev 0.33
port 2 powered
port 3 powered
port 4 powered

 My primary hard drives are da0 and da1 (all the how-to's say that daX
> should be where I mount.. but /dev only has my two primary drives:
>
> -su-2.05b# ls -la /dev/da*
> crw-r----- 1 root operator 4, 16 Dec 20 20:11 /dev/da0
> crw-r----- 1 root operator 4, 18 Dec 20 12:11 /dev/da0a
> crw-r----- 1 root operator 4, 19 Dec 20 20:11 /dev/da0b
> crw-r----- 1 root operator 4, 20 Dec 20 20:11 /dev/da0c
> crw-r----- 1 root operator 4, 17 Dec 20 20:11 /dev/da1
> crw-r----- 1 root operator 4, 21 Dec 20 20:11 /dev/da1c
> crw-r----- 1 root operator 4, 22 Dec 20 12:11 /dev/da1d
>
> -su-2.05b# dmesg|grep da.:
> da0: <FUJITSU MAN3367M SUN36G 1502> Fixed Direct Access SCSI-2 device
> da0: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing
> Enabled
> da0: 34732MB (71132959 512 byte sectors: 255H 63S/T 4427C)
> da1: <FUJITSU MAN3367M SUN36G 1502> Fixed Direct Access SCSI-2 device
> da1: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing
> Enabled
> da1: 34732MB (71132959 512 byte sectors: 255H 63S/T 4427C)
>
> I can plug this into my AMD64 running FreeBSD 6, and it comes up with no
> problems.
>
> I THINK I'm probably missing something totally dumb... Anyone got any help
> for me on this?
>
> Yah.. I know.. get an i386 box with IDE drives.  :) This is a small 1U
> box, and fits in my closet well. so I'd like to use it if possible.
>
> Thanks!!!
> Aaron
>
>