5.4 reboots when I plug in a flash drive?

Lowell Gilbert freebsd-questions-local at be-well.ilk.org
Tue Oct 4 17:49:45 PDT 2005


Brian John <brianjohn at fusemail.com> writes:

> Parv wrote:
> 
> >in message
> ><1468.209.87.176.132.1128439684.fusewebmail-19592 at webmail.fusemail.com
> >
> >>, wrote Brian John thusly...
> >>
> >>I just got a 128MB USB flash drive.  When I plug it in in FreeBSD,
> >>the box promptly reboots!  What would cause this?
> >>
> >
> >I don't know the cause.
> >
> >Have you tried booting FreeBSD from power-off state w/ the flash
> >drive already inserted?  That may solve your booting problem, but
> >will not make use of the drive any easier.
> >
> >Which version if FreeBSD are you using?  Which of the [ueo]hci
> >drivers come up in dmesg(8) on instertion of the USB drive?
> >
> >
> >  - Parv
> >
> >
> Ok, I tried booting up with the drive installed.  If I leave it
> installed while it is booting up, it eventually reboots.  However, I
> was able to unplug it during boot and look at dmesg.  It says this
> over and over again:
> 
> umass0: vendor 0x10d6 USB 2.0(FS) FLASH DISK, rev 1.10/1.00, addr 2
> da0 at umass-sim0 bus 0 target 0 lun 0
> da0: <USB2.0 (FS) FLASH DISK 1.00> Removable Direct Access SCSI-0 device
> da0: 1.000MB/s transfers
> da0: 119MB (245473 512 byte sectors: 64H 32S/T 119C)
> umass0: BBB reset failed, STALLED
> umass0: BBB bulk-in clear stall failed, STALLED
> umass0: BBB bulk-out clear stall failed, STALLED
> (da0:umass-sim0:0:0:0): Synchronize cache failed, status == 0x4, scsi
> status == 0x0
> umass0: BBB reset failed, STALLED
> umass0: BBB bulk-in clear stall failed, STALLED
> umass0: BBB bulk-out clear stall failed, STALLED
> umass0: BBB reset failed, STALLED
> umass0: BBB bulk-in clear stall failed, STALLED
> umass0: BBB bulk-out clear stall failed, STALLED
> umass0: BBB reset failed, STALLED
> umass0: BBB bulk-in clear stall failed, STALLED
> umass0: BBB bulk-out clear stall failed, STALLED
> umass0: BBB reset failed, STALLED
> umass0: BBB bulk-in clear stall failed, STALLED
> umass0: BBB bulk-out clear stall failed, STALLED
> umass0: BBB reset failed, STALLED
> umass0: BBB bulk-in clear stall failed, STALLED
> umass0: BBB bulk-out clear stall failed, STALLED
> umass0: at uhub2 port 1 (addr 2) disconnected
> (da0:umass-sim0:0:0:0): lost device
> (da0:umass-sim0:0:0:0): removing device entry
> Opened disk da0 -> 5
> umass0: detached
> 
> I am running FreeBSD 5.4.  Does this shed some light on the problem?

Only a little.  Do you have udbp(4) in your kernel?  
Can you try booting 6.0 with the flash unit plugged in and see if it
still has problems?


More information about the freebsd-questions mailing list