PPPOE using PPP IPCP problem

[Kris]

Hi

 

I am trying to connect to a DSL provider in Australia called OPTUS. I have
configured many other DSL providers with no hassle previously but this
particular ISP I keep running into the following problems which I hope
*someone* can shed some light on. 

 

I have tried the box that I will be using and the same ppp configuration on
my ADSL provider at home with no problems at all, just for piece of mind
that the box itself and everything is working.

 

Here is the ppp.conf and then the resulting log file. I seem to be getting
Authenticated and then being sent an IPCP request to configure my local and
remote IP's etc.. but it seems it is being ignored because ppp is still in
the Authenticate state. A seen in the log towards the end..

 

 tun0: Phase: Pap Input: SUCCESS ()

 tun0: IPCP: deflink: Error: Unexpected IPCP in phase Authenticate (ignored)

 last message repeated 6 times

 last message repeated 2 times

 

 

Does anyone have any ideas as to what is going on and how I may fix it ?

 

Kris

 

 

---start ppp.conf------

default:

 

 set log Chat Connect command tun Phase Warning LCP IPCP CCP

 enable dns

 set redial 0 0

 set timeout 0

 disable lqr

 disable ipv6cp

 

optus:

 

 set device PPPoE:dc0

 set authname xxxxxxxx at optusnet.com.au

 set authkey xxxxxxx

 set dial

 set login

 set speed sync

 set mtu 1492

 set mru 1492

 set ctsrts off

 enable dns

 set ifaddr 10.0.0.1/0 10.0.0.2/0 255.255.255.0 0.0.0.0

 add 0 0 HISADDR

 

----- end ppp.conf-----

 

--- start ppp.log--------

 

Phase: Using interface: tun0

 Phase: deflink: Created in closed state

 tun0: Command: default: enable dns

 tun0: Command: default: set redial 0 0

 tun0: Command: default: set timeout 0

 tun0: Command: default: disable lqr

 tun0: Command: default: disable ipv6cp

 tun0: Command: optus: set device PPPoE:dc0

 tun0: Command: optus: set authname xxxxxxxxxxxx at optusnet.com.au

 tun0: Command: optus: set authkey ********

 tun0: Command: optus: set dial

 tun0: Command: optus: set login

 tun0: Command: optus: set speed sync

 tun0: Command: optus: set mtu 1492

 tun0: Command: optus: set mru 1492

 tun0: Command: optus: set ctsrts off

 tun0: Command: optus: enable dns

 tun0: Command: optus: set ifaddr 10.0.0.1/0 10.0.0.2/0 255.255.255.0
0.0.0.0

 tun0: Command: optus: add 0 0 HISADDR

 tun0: Warning: Add route failed: 0.0.0.0/0 already exists

 tun0: Phase: PPP Started (ddial mode).

 tun0: Phase: bundle: Establish

 tun0: Phase: deflink: closed -> opening

 tun0: Phase: deflink: Connected!

 tun0: Phase: deflink: opening -> dial

 tun0: Phase: deflink: dial -> carrier

 tun0: Phase: Received NGM_PPPOE_ACNAME (hook "qcb1-charlotte")

 tun0: Phase: Received NGM_PPPOE_SESSIONID

 tun0: Phase: Received NGM_PPPOE_SUCCESS

 tun0: Phase: deflink: carrier -> login

 tun0: Phase: deflink: login -> lcp

 tun0: LCP: FSM: Using "deflink" as a transport

 tun0: LCP: deflink: State change Initial --> Closed

 tun0: LCP: deflink: State change Closed --> Stopped

 tun0: LCP: deflink: RecvConfigReq(12) state = Stopped

 tun0: LCP:  MRU[4] 1492

 tun0: LCP:  AUTHPROTO[5] 0xc223 (CHAP 0x05)

 tun0: LCP:  MAGICNUM[6] 0x12402c2b

 tun0: LCP: deflink: SendConfigReq(1) state = Stopped

 tun0: LCP:  MRU[4] 1492

 tun0: LCP:  MAGICNUM[6] 0xd914771a

 tun0: LCP: deflink: SendConfigAck(12) state = Stopped

 tun0: LCP:  MRU[4] 1492

 tun0: LCP:  AUTHPROTO[5] 0xc223 (CHAP 0x05)

 tun0: LCP:  MAGICNUM[6] 0x12402c2b

 tun0: LCP: deflink: LayerStart

 tun0: LCP: deflink: State change Stopped --> Ack-Sent

 tun0: LCP: deflink: RecvConfigAck(1) state = Ack-Sent

 tun0: LCP:  MRU[4] 1492

 tun0: LCP:  MAGICNUM[6] 0xd914771a

 tun0: LCP: deflink: State change Ack-Sent --> Opened

 tun0: LCP: deflink: LayerUp

 tun0: Phase: bundle: Authenticate

 tun0: Phase: deflink: his = CHAP 0x05, mine = none

 tun0: Phase: Chap Input: CHALLENGE (16 bytes from qcb1-charlotte)

 tun0: Phase: Chap Output: RESPONSE (xxxxxxxxx at optusnet.com.au)

 tun0: LCP: deflink: RecvConfigReq(128) state = Opened

 tun0: LCP: deflink: LayerDown

 tun0: LCP:  AUTHPROTO[4] 0xc023 (PAP)

 tun0: LCP: deflink: SendConfigReq(2) state = Opened

 tun0: LCP:  MRU[4] 1492

 tun0: LCP:  MAGICNUM[6] 0xb3531398

 tun0: LCP: deflink: SendConfigNak(128) state = Opened

 tun0: LCP:  MRU[4] 1492

 tun0: LCP: deflink: State change Opened --> Req-Sent

 tun0: LCP: deflink: RecvConfigAck(2) state = Req-Sent

 tun0: LCP:  MRU[4] 1492

 tun0: LCP:  MAGICNUM[6] 0xb3531398

 tun0: LCP: deflink: State change Req-Sent --> Ack-Rcvd

 tun0: LCP: deflink: RecvConfigReq(128) state = Ack-Rcvd

 tun0: LCP:  AUTHPROTO[4] 0xc023 (PAP)

 tun0: LCP: deflink: SendConfigAck(128) state = Ack-Rcvd

 tun0: LCP:  AUTHPROTO[4] 0xc023 (PAP)

 tun0: LCP: deflink: State change Ack-Rcvd --> Opened

 tun0: LCP: deflink: LayerUp

 tun0: Phase: deflink: his = PAP, mine = none

 tun0: Phase: Pap Output: xxxxxxxxxx at optusnet.com.au ********

 tun0: LCP: deflink: RecvConfigReq(128) state = Opened

 tun0: LCP: deflink: LayerDown

 tun0: LCP:  AUTHPROTO[4] 0xc023 (PAP)

 tun0: LCP: deflink: SendConfigReq(3) state = Opened

 tun0: LCP:  MRU[4] 1492

 tun0: LCP:  MAGICNUM[6] 0x593cf6b6

 tun0: LCP: deflink: SendConfigNak(128) state = Opened

 tun0: LCP:  MRU[4] 1492

 tun0: LCP: deflink: State change Opened --> Req-Sent

 tun0: LCP: deflink: RecvConfigAck(3) state = Req-Sent

 tun0: LCP:  MRU[4] 1492

 tun0: LCP:  MAGICNUM[6] 0x593cf6b6

 tun0: LCP: deflink: State change Req-Sent --> Ack-Rcvd

 tun0: Phase: Pap Input: SUCCESS ()

 tun0: IPCP: deflink: Error: Unexpected IPCP in phase Authenticate (ignored)

 last message repeated 6 times

 last message repeated 2 times

 tun0: Phase: Signal 15, terminate.