DVD burner error

[Edvard Fagerholm]

On Wed, Nov 24, 2004 at 05:24:36PM -0600, Andrew L. Gould wrote:
> On Wednesday 24 November 2004 05:02 pm, Edvard Fagerholm wrote:
> > On Wed, Nov 24, 2004 at 11:27:03PM +0200, Edvard Fagerholm wrote:
> > > Hello!
> > >
> > > I get sometimes the following error when I burn DVDs. Actually it
> > > happens more often than not... When burning a DVD with growisofs,
> > > burning stops with the following message:
> > >
> > > acd0 WARNING - removed from configuration
> > >
> > > :-( unable to WRITE at LBA=fb150h: Input/output error
> > >
> > > builtin_dd: 1028432*2KB out @ average 3.5x1385KBps
> > >
> > > :-( write failed: Input/output error
> > >
> > > /dev/pass0: flushing cache
> > > (cd0:ata1:0:0:0): lost device
> > > (probe0:ata1:0:0:0): Lost target 0???
> > >
> > > :-( unable to FLUSH CACHE: Input/output error
> > > :-( unable to SYNCHRONOUS FLUSH CACHE: Input/output error
> > >
> > > (cd0:ata1:0:0:0): removing device entry
> > >
> > > The funny thing is that this seems to be very file dependent. If I
> > > create an ISO it might work fine and I can burn it many times with
> > > no failures. However, some files always fail. With burncd I can
> > > burn every file, but fixating doesn't work. The error message I get
> > > with burncd is TEST_UNIT_READY Illegal request. I can get the exact
> > > data later (i.e. the next time I want to destroy yet another DVD).
> > >
> > > My DVD drive is an LG GSA-4160B
> > >
> > > Regards,
> > > Edvard
> >
> > Ok, I forgot to add that I'm running FreeBSD 5.3R. I also tried to
> > use burncd to get the error message I mentioned in my earlier mail,
> > but this time I got a kernel panic instead. I didn't see exactly what
> > happened, but when I returned to the computer I saw this:
> >
> > burncd: ioctl(CDRIOCSETBLOCKSIZE): Device not configured
> > burncd: ioctl(CDRIOCSETBLOCKSIZE): Device not configured
> > burncd: ioctl(CDRIOCSETBLOCKSIZE): Device not configured
> > ...
> > burncd: ioctl(CDRIOCSETBLOCKSIZE): Device not configured
> >
> > Fatal trap 12: page fault while in kernel mode
> > fault virtual address	= 0x0
> > fault code		= supervisor read, page not present
> > instruction pointer	= 0x8:0xc0440470
> > stack pointer		= 0x10:0xd4030bfc
> > frame pointer		= 0x10:0xd4030c08
> > code segment		= base 0x0, limit 0xffff, type 0x1b
> > 			= DPL 0, pres 1, def32 1, gran 1
> > processor eflags	= interrupt enabled, resume, IOPL = 0
> > current process		= 2 (g_event)
> > trap number		= 12
> > panic: page fault
> >
> > I'm happy to provide extra information. I could look up the offending
> > code with the kernel debugger tomorrow (it's 1AM, so I don't feel
> > like it now).
> >
> > dmesg output as attachment.
> >
> > - edvard
> 
> See the following links regarding burning cd's and dvd's.  With a DVD 
> burner, you need to add atapicam to the your kernel.  The use of 
> atapicam will also mean, however, that you will need to burn cd's using 
> cdrecord rather than burncd.
> 
> http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/creating-cds.html
> http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/creating-dvds.html
> 
> Best of luck,
> 
> Andrew Gould

I have atapicam installed. If you check my previous mail, you'll see that I was
using growisofs and all errors had something to do with /dev/cd0 and
/dev/pass0. Those are the atapicam devices. I tried to use burncd, because
atapicam burning was failing.

I already read the handbook when I installed the dvd burner and it has no
information that could be to any help regarding this problem.

- edvard