Problems Mounting CDROM

Tue Mar 2 12:05:16 PST 2004

On Tue, 02 Mar 2004 11:46:56 -0800
Rishi Chopra <rchopra at cal.berkeley.edu> wrote:

> Here's the dmesg (Kernel config also included below):
> 
> Copyright (c) 1992-2003 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
>          The Regents of the University of California. All rights reserved.
> FreeBSD 5.1-RELEASE #0: Sat Dec 13 07:05:15 PST 2003
>      root at idfubar.dyndns.org:/usr/src/sys/i386/compile/VISION
> Preloaded elf kernel "/boot/kernel/kernel" at 0xc068f000.
> Timecounter "i8254"  frequency 1193182 Hz
> Timecounter "TSC"  frequency 119752863 Hz
> CPU: Pentium/P54C (119.75-MHz 586-class CPU)
>    Origin = "GenuineIntel"  Id = 0x525  Stepping = 5
>    Features=0x1bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8>
> real memory  = 100663296 (96 MB)
> avail memory = 90685440 (86 MB)
> Intel Pentium detected, installing workaround for F00F bug
> npx0: <math processor> on motherboard
> npx0: INT 16 interface
> pcibios: BIOS version 2.10
> pcib0: <Host to PCI bridge> at pcibus 0 on motherboard
> pci0: <PCI bus> on pcib0
> isab0: <PCI-ISA bridge> at device 7.0 on pci0
> isa0: <ISA bus> on isab0
> atapci0: <Intel PIIX WDMA2 controller> port 0xffa0-0xffaf at device 7.1 
> on pci0
> atapci0: Busmastering DMA not supported
> ata0: at 0x1f0 irq 14 on atapci0
> ata1: at 0x170 irq 15 on atapci0
> pci0: <display, VGA> at device 13.0 (no driver attached)
> asr0: <Adaptec Caching SCSI RAID> mem 0xf0000000-0xf7ffffff irq 5 at 
> device 14.0 on pci0
> asr0: major=154
> asr0: ADAPTEC 2400A FW Rev. 3A0L, 4 channel, 256 CCBs, Protocol I2O
> pcib1: <PCI-PCI bridge> at device 14.1 on pci0
> pci1: <PCI bus> on pcib1
> rl0: <RealTek 8139 10/100BaseTX> port 0xf880-0xf8ff mem 
> 0xfffbfc00-0xfffbfc7f irq 9 at device 15.0 on pci0
> rl0: Ethernet address: 00:00:b4:91:28:03
> miibus0: <MII bus> on rl0
> rlphy0: <RealTek internal media interface> on miibus0
> rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> rl1: <RealTek 8139 10/100BaseTX> port 0xfc00-0xfcff mem 
> 0xfffb7c00-0xfffb7cff irq 10 at device 16.0 on pci0
> rl1: Realtek 8139B detected. Warning, this may be unstable in autoselect 
> mode
> rl1: Ethernet address: 00:50:fc:21:df:8f
> miibus1: <MII bus> on rl1
> rlphy1: <RealTek internal media interface> on miibus1
> rlphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> orm0: <Option ROMs> at iomem 
> 0xed000-0xedfff,0xc8000-0xcdfff,0xc0000-0xc7fff on isa0
> pmtimer0 on isa0
> atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
> atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
> kbd0 at atkbd0
> fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> at port 
> 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
> fdc0: FIFO enabled, 8 bytes threshold
> fd0: <1440-KB 3.5" drive> on fdc0 drive 0
> ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
> ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
> ppbus0: <Parallel port bus> on ppc0
> plip0: <PLIP network interface> on ppbus0
> lpt0: <Printer> on ppbus0
> lpt0: Interrupt-driven port
> ppi0: <Parallel I/O> on ppbus0
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
> sio0: type 16550A
> sio1 at port 0x2f8-0x2ff irq 3 on isa0
> sio1: type 16550A
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> unknown: <PNP0303> can't assign resources (port)
> unknown: <PNP0700> can't assign resources (port)
> unknown: <PNP0400> can't assign resources (port)
> unknown: <PNP0501> can't assign resources (port)
> unknown: <PNP0501> can't assign resources (port)
> Timecounters tick every 10.000 msec
> ipfw2 initialized, divert enabled, rule-based forwarding enabled, 
> default to deny, logging disabled
> da0 at asr0 bus 0 target 0 lun 0
> da0: <ADAPTEC RAID-5 3A0L> Fixed Direct Access SCSI-2 device
> da0: 572202MB (1171869696 512 byte sectors: 255H 63S/T 72945C)
> Mounting root from ufs:/dev/da0s1a
> WARNING: / was not properly dismounted
> WARNING: /usr was not properly dismounted
> WARNING: /var was not properly dismounted
> 
> Kernel config file shows the following:
> 
> options         CD9660                  #ISO 9660 Filesystem
> device          atapicd                 # ATAPI CDROM drives
> device          cd              # CD

It doesn't show up any atapi (IDE) CDROM. Is it IDE ? If not, do you
have the appropriate SCSI in your kernel ?

-- 
IOnut
Unregistered ;) FreeBSD user