Dell PowerEdge 2650 - PCI PARITY E13F4
Gil Klein
gklein at barak013.net.il
Mon Sep 29 01:42:14 PDT 2003
Hello,
I am running FreeBSD 4.8R on 2 servers with the same hardware configuration.
Both Dell PowerEdge 2650 with 2 x 3Ghz CPU and 4GB RAM.
Once in a while both servers reboots at a random time with no error message
at any log file and the LCD says PCI PARITY E13F4.
I tried replacing mother boards + expansion packs as Dell recommended, but
the problem persists. I also removed all PCI adapters and the external disks
but no luck solving the problem.
When running Windows 2000 on the same servers it work smoothly with no
alerts and no reboots at all.
Do you have any idea what may be causing the problem ?
I attached the dmesg.boot + kernel diff.
Thanks,
Gil
dmesg.boot
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.8-RELEASE #4: Wed Aug 6 11:46:18 IDT 2003
root at moria:/usr/src/sys/compile/MORIA
<mailto:root at moria:/usr/src/sys/compile/MORIA>
Timecounter "i8254" frequency 1193182 Hz
CPU: Intel(R) Xeon(TM) CPU 3.06GHz (3056.51-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf29 Stepping = 9
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA
,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Hyperthreading: 2 logical CPUs
real memory = 4026466304 (3932096K bytes)
avail memory = 3920564224 (3828676K bytes)
Changing APIC ID for IO APIC #0 from 0 to 8 on chip
Changing APIC ID for IO APIC #1 from 0 to 9 on chip
Changing APIC ID for IO APIC #2 from 0 to 10 on chip
Programming 16 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
Programming 16 pins in IOAPIC #1
Programming 16 pins in IOAPIC #2
FreeBSD/SMP: Multiprocessor motherboard
cpu0 (BSP): apic id: 0, version: 0x00050014, at 0xfee00000
cpu1 (AP): apic id: 6, version: 0x00050014, at 0xfee00000
io0 (APIC): apic id: 8, version: 0x000f0011, at 0xfec00000
io1 (APIC): apic id: 9, version: 0x000f0011, at 0xfec01000
io2 (APIC): apic id: 10, version: 0x000f0011, at 0xfec02000
Preloaded elf kernel "kernel" at 0xc0532000.
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 9 entries at 0xc00fc430
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
IOAPIC #1 intpin 3 -> irq 2
IOAPIC #1 intpin 7 -> irq 7
IOAPIC #1 intpin 11 -> irq 10
pci0: <PCI bus> on pcib0
pci0: <unknown card> (vendor=0x1028, dev=0x000c) at 4.0 irq 2
pci0: <unknown card> (vendor=0x1028, dev=0x0008) at 4.1 irq 7
pci0: <unknown card> (vendor=0x1028, dev=0x000d) at 4.2 irq 10
pci0: <ATI Mach64-GR graphics accelerator> at 14.0
atapci0: <ServerWorks CSB5 ATA100 controller> port
0x8b0-0x8bf,0x8d8-0x8db,0x8d0-0x8d7,0x8c8-0x8cb,0x8c0-0x8c7 at device 15.1
on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
ohci0: <OHCI (generic) USB controller> mem 0xfe100000-0xfe100fff irq 5 at
device 15.2 on pci0
usb0: OHCI version 1.0, legacy support
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
isab0: <PCI to ISA bridge (vendor=1166 device=0225)> at device 15.3 on pci0
isa0: <ISA bus> on isab0
pcib1: <Host to PCI bridge> on motherboard
IOAPIC #1 intpin 4 -> irq 11
IOAPIC #1 intpin 5 -> irq 13
pci1: <PCI bus> on pcib1
ahc0: <Adaptec 3960D Ultra160 SCSI adapter> port 0xdc00-0xdcff mem
0xfcf01000-0xfcf01fff irq 11 at device 8.0 on pci1
aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
ahc1: <Adaptec 3960D Ultra160 SCSI adapter> port 0xd800-0xd8ff mem
0xfcf00000-0xfcf00fff irq 13 at device 8.1 on pci1
aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs
pcib2: <Host to PCI bridge> on motherboard
pci2: <PCI bus> on pcib2
pcib3: <Host to PCI bridge> on motherboard
IOAPIC #1 intpin 12 -> irq 16
IOAPIC #1 intpin 13 -> irq 17
pci3: <PCI bus> on pcib3
bge0: <Broadcom BCM5703X Gigabit Ethernet, ASIC rev. 0x1002> mem
0xfcd10000-0xfcd1ffff irq 16 at device 6.0 on pci3
bge0: Ethernet address: 00:0b:db:d5:1a:c6
miibus0: <MII bus> on bge0
brgphy0: <BCM5703 10/100/1000baseTX PHY> on miibus0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
1000baseTX-FDX, auto
bge1: <Broadcom BCM5703X Gigabit Ethernet, ASIC rev. 0x1002> mem
0xfcd00000-0xfcd0ffff irq 17 at device 8.0 on pci3
bge1: Ethernet address: 00:0b:db:d5:1a:c7
miibus1: <MII bus> on bge1
brgphy1: <BCM5703 10/100/1000baseTX PHY> on miibus1
brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
1000baseTX-FDX, auto
pcib4: <ServerWorks host to PCI bridge(unknown chipset)> on motherboard
IOAPIC #1 intpin 14 -> irq 18
pci4: <PCI bus> on pcib4
pcib8: <PCI to PCI bridge (vendor=8086 device=0309)> at device 8.0 on pci4
IOAPIC #1 intpin 15 -> irq 19
pci5: <PCI bus> on pcib8
pci5: <unknown card> (vendor=0x9005, dev=0x00c5) at 6.0 irq 18
pci5: <unknown card> (vendor=0x9005, dev=0x00c5) at 6.1 irq 19
aac0: <Dell PERC 3/Di> mem 0xf0000000-0xf7ffffff irq 18 at device 8.1 on
pci4
aac0: i960RX 100MHz, 118MB cache memory, optional battery present
aac0: Kernel 2.7-1, Build 3170, S/N 7620d3
pcib5: <ServerWorks host to PCI bridge(unknown chipset)> on motherboard
pci6: <PCI bus> on pcib5
pcib6: <ServerWorks host to PCI bridge(unknown chipset)> on motherboard
pci7: <PCI bus> on pcib6
pcib7: <ServerWorks host to PCI bridge(unknown chipset)> on motherboard
pci8: <PCI bus> on pcib7
orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xcbfff,0xec000-0xeffff
on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: parallel port not found.
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: Broken MP table detected: 8254 is not connected to IOAPIC #0 intpin
2
APIC_IO: routing 8254 via 8259 and IOAPIC #0 intpin 0
IP packet filtering initialized, divert disabled, rule-based forwarding
enabled, default to accept, logging limited to 10 packets/entry by default
ata0-slave: ATAPI identify retries exceeded
SMP: AP CPU #1 Launched!
acd0: CDROM <TEAC CD-ROM CD-224E> at ata0-master PIO4
Waiting 15 seconds for SCSI devices to settle
aacd0: <RAID 1 (Mirror)> on aac0
aacd0: 69998MB (143357184 sectors)
aacd1: <RAID 0 (Stripe)> on aac0
aacd1: 69998MB (143357184 sectors)
aacd2: <RAID 0 (Stripe)> on aac0
aacd2: 69998MB (143357184 sectors)
aacd3: <RAID 0 (Stripe)> on aac0
aacd3: 69998MB (143357184 sectors)
pass6 at ahc0 bus 0 target 6 lun 0
pass6: <DELL PV22XS E.11> Fixed Processor SCSI-3 device
pass6: 3.300MB/s transfers
pass8 at ahc1 bus 0 target 6 lun 0
pass8: <DELL PV22XS E.11> Fixed Processor SCSI-3 device
pass8: 3.300MB/s transfers
da0 at ahc0 bus 0 target 0 lun 0
da0: <FUJITSU MAS3735NC 5B06> Fixed Direct Access SCSI-3 device
da0: 160.000MB/s transfers (80.000MHz, offset 127, 16bit), Tagged Queueing
Enabled
da0: 70007MB (143374650 512 byte sectors: 255H 63S/T 8924C)
da7 at ahc1 bus 0 target 9 lun 0
da7: <FUJITSU MAS3735NC 5B06> Fixed Direct Access SCSI-3 device
da7: 160.000MB/s transfers (80.000MHz, offset 127, 16bit), Tagged Queueing
Enabled
da7: 70007MB (143374650 512 byte sectors: 255H 63S/T 8924C)
da3 at ahc0 bus 0 target 3 lun 0
da3: <FUJITSU MAS3735NC 5B06> Fixed Direct Access SCSI-3 device
da3: 160.000MB/s transfers (80.000MHz, offset 127, 16bit), Tagged Queueing
Enabled
da3: 70007MB (143374650 512 byte sectors: 255H 63S/T 8924C)
da10 at ahc1 bus 0 target 12 lun 0
da10: <FUJITSU MAS3735NC 5B06> Fixed Direct Access SCSI-3 device
da10: 160.000MB/s transfers (80.000MHz, offset 127, 16bit), Tagged Queueing
Enabled
da10: 70007MB (143374650 512 byte sectors: 255H 63S/T 8924C)
da4 at ahc0 bus 0 target 4 lun 0
da4: <FUJITSU MAS3735NC 5B06> Fixed Direct Access SCSI-3 device
da4: 160.000MB/s transfers (80.000MHz, offset 127, 16bit), Tagged Queueing
Enabled
da4: 70007MB (143374650 512 byte sectors: 255H 63S/T 8924C)
da11 at ahc1 bus 0 target 13 lun 0
da11: <FUJITSU MAS3735NC 5B06> Fixed Direct Access SCSI-3 device
da11: 160.000MB/s transfers (80.000MHz, offset 127, 16bit), Tagged Queueing
Enabled
da11: 70007MB (143374650 512 byte sectors: 255H 63S/T 8924C)
da5 at ahc0 bus 0 target 5 lun 0
da5: <FUJITSU MAS3735NC 5B06> Fixed Direct Access SCSI-3 device
da5: 160.000MB/s transfers (80.000MHz, offset 127, 16bit), Tagged Queueing
Enabled
da5: 70007MB (143374650 512 byte sectors: 255H 63S/T 8924C)
da12 at ahc1 bus 0 target 14 lun 0
da12: <FUJITSU MAS3735NC 5B06> Fixed Direct Access SCSI-3 device
da12: 160.000MB/s transfers (80.000MHz, offset 127, 16bit), Tagged Queueing
Enabled
da12: 70007MB (143374650 512 byte sectors: 255H 63S/T 8924C)
da2 at ahc0 bus 0 target 2 lun 0
da2: <FUJITSU MAS3735NC 5B06> Fixed Direct Access SCSI-3 device
da2: 160.000MB/s transfers (80.000MHz, offset 127, 16bit), Tagged Queueing
Enabled
da2: 70007MB (143374650 512 byte sectors: 255H 63S/T 8924C)
da9 at ahc1 bus 0 target 11 lun 0
da9: <FUJITSU MAS3735NC 5B06> Fixed Direct Access SCSI-3 device
da9: 160.000MB/s transfers (80.000MHz, offset 127, 16bit), Tagged Queueing
Enabled
da9: 70007MB (143374650 512 byte sectors: 255H 63S/T 8924C)
da1 at ahc0 bus 0 target 1 lun 0
da1: <FUJITSU MAS3735NC 5B06> Fixed Direct Access SCSI-3 device
da1: 160.000MB/s transfers (80.000MHz, offset 127, 16bit), Tagged Queueing
Enabled
da1: 70007MB (143374650 512 byte sectors: 255H 63S/T 8924C)
da13 at ahc1 bus 0 target 15 lun 0
da13: <FUJITSU MAS3735NC 5B06> Fixed Direct Access SCSI-3 device
da13: 160.000MB/s transfers (80.000MHz, offset 127, 16bit), Tagged Queueing
Enabled
da13: 70007MB (143374650 512 byte sectors: 255H 63S/T 8924C)
da6 at ahc0 bus 0 target 8 lun 0
da6: <FUJITSU MAS3735NC 5B06> Fixed Direct Access SCSI-3 device
da6: 160.000MB/s transfers (80.000MHz, offset 127, 16bit), Tagged Queueing
Enabled
da6: 70007MB (143374650 512 byte sectors: 255H 63S/T 8924C)
da8 at ahc1 bus 0 target 10 lun 0
da8: <FUJITSU MAS3735NC 5B06> Fixed Direct Access SCSI-3 device
da8: 160.000MB/s transfers (80.000MHz, offset 127, 16bit), Tagged Queueing
Enabled
da8: 70007MB (143374650 512 byte sectors: 255H 63S/T 8924C)
Mounting root from ufs:/dev/aacd0s1a
diff GENERIC MORIA
64,65c64,65
< #options SMP # Symmetric MultiProcessor Kernel
< #options APIC_IO # Symmetric (APIC) I/O
---
> options SMP # Symmetric MultiProcessor Kernel
> options APIC_IO # Symmetric (APIC) I/O
266a267,277
>
> # Peercache Tunning
> #options MAXDSIZ="(3072*1024*1024)"
> #options MAXDSIZ="(2048*1024*1024)"
> options MAXDSIZ="(1536*1024*1024)"
>
> # IPFW Configuration
> options IPFIREWALL
> options IPFIREWALL_VERBOSE
> options IPFIREWALL_VERBOSE_LIMIT=10
> options IPFIREWALL_DEFAULT_TO_ACCEPT
**********************************************************************
The information contained in this e-mail message may be
privileged and confidential. The information is intended only
for the use of the individual or entity named above. If the
reader of this message is not the intended recipient, you are
hereby notified that any dissemination, distribution or copying
of this communication is strictly prohibited. If you have
received this communication in error, please notify us
mmediately by telephone, or by e-mail and delete the message
from your computer. Thank you!
Unless otherwise stated, any views or opinions expressed in
this e-mail are solely those of the author and do not represent those of Barak I.T.C (1995)The International Telecommunications Services Corp. Ltd.
**********************************************************************
More information about the freebsd-questions
mailing list