SCSI Disk not found

Wed Dec 3 08:11:41 PST 2003

Ok, its the "System Configuration Utility" supplied by Compaq not the
BIOS. 

I added puc to kernel and it still has the same irq. 

This machine was in the closet for a long while... and it had no
operating system installed when I got it, but I think it may have had
windows NT. 

Thanks for your help,

Michael

On Wed, 2003-12-03 at 09:49, fbsd_user wrote:
> What do you mean SCSI HD show in PC bios?  I have not seen any PC
> bio's that know about SCSI drives. They are not part of the normal
> PC hardware inventory. SCSI drives are 3rd party hardware. Your
> bio's option 'drive to boot from' is the only place that knows about
> SCSI. It should say boot from SCSI drive, or something along those
> lines. The SCSI PCI control card knows about the 2 drive if it's
> there. During the PC boot process you should see msg about SCSI
> controller being enabled. AT that point you should be able to enter
> SCSI setup utility.
> 
> I see from dmesg that both drives are using same irq. This is common
> problem with older PC bios, FBSD can not reassign different IRQ to
> second device.   Add  device puc statement to your kernel source and
> recompile kernel. Them check Dmesg boot log to see if different
> IRQ's get assigned.
> 
> Before you installed FBSD on this PC, was it running ms/windows and
> did you see the both SCSI drives?
> 
> 
> 
> -----Original Message-----
> From: owner-freebsd-questions at freebsd.org
> [mailto:owner-freebsd-questions at freebsd.org]On Behalf Of Michael E.
> Mercer
> Sent: Wednesday, December 03, 2003 9:14 AM
> To: fbsd_user at a1poweruser.com
> Cc: freebsd-questions at freebsd.org
> Subject: RE: SCSI Disk not found
> 
> Hello,
> 
> I wish it were that easy... I really meant that FreeBSD does NOT
> see it at all. I have tried to mount it myself, but it tells
> me that the device is not configured.
> 
> The SCSI hard drive appears in the system BIOS, and when the machine
> first boots up, but it is gone everywhere else.
> 
> Any ideas?
> 
> Michael
> 
> On Wed, 2003-12-03 at 09:09, fbsd_user wrote:
> > You have to add an line to the /etc/fstab file for the second HD.
> > You can mount it as an msdos HD or you can use FBSD to fdisk,
> label,
> > and format it to FBSD file system.  It's up to you and how you
> want
> > to use it.
> >
> > -----Original Message-----
> > From: owner-freebsd-questions at freebsd.org
> > [mailto:owner-freebsd-questions at freebsd.org]On Behalf Of Michael
> E.
> > Mercer
> > Sent: Tuesday, December 02, 2003 11:38 PM
> > To: freebsd-questions at freebsd.org
> > Subject: SCSI Disk not found
> >
> > Hello peoples,
> >
> > I was given a Compaq Proliant 800 machine...its a pentium pro
> > 200 MHz. I got 4.9-Stable installed and everything is running
> > smooth.
> >
> > However, I noticed that is does indeed have two scsi disks,
> > but freebsd only finds one.
> >
> > Attached is the dmesg... notice the sym0 and sym1.
> > Does this supposed to tell me anything?
> >
> > Thanks
> > Michael E Mercer
> >
> > Copyright (c) 1992-2003 The FreeBSD Project.
> > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992,
> 1993,
> > 1994
> >         The Regents of the University of California. All rights
> > reserved.
> > FreeBSD 4.9-STABLE #0: Tue Dec  2 21:45:22 EST 2003
> >     root at slow.nc.rr.com:/usr/src/sys/compile/slow_4_9
> > Timecounter "i8254"  frequency 1193182 Hz
> > CPU: Pentium Pro (199.43-MHz 686-class CPU)
> >   Origin = "GenuineIntel"  Id = 0x619  Stepping = 9
> >
> >
> Features=0xf9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,
> > CMOV>
> > real memory  = 301989888 (294912K bytes)
> > avail memory = 288219136 (281464K bytes)
> > Preloaded elf kernel "kernel" at 0xc0491000.
> > Preloaded userconfig_script "/boot/kernel.conf" at 0xc049109c.
> > ccd0-3: Concatenated disk drivers
> > VESA: v1.2, 1024k memory, flags:0x0, mode table:0xc03f8994
> (1000014)
> > VESA: STB COMPAQ 5440
> > Pentium Pro MTRR support enabled
> > md0: Malloc disk
> > npx0: <math processor> on motherboard
> > npx0: INT 16 interface
> > pcib0: <Host to PCI bridge> on motherboard
> > pci0: <PCI bus> on pcib0
> > pcib1: <IBM 82351 PCI-PCI bridge> at device 8.0 on pci0
> > pci1: <PCI bus> on pcib1
> > sym0: <875> port 0x7000-0x70ff mem
> > 0x40100000-0x40100fff,0x40102000-0x401020ff irq 5 at device 4.0 on
> > pci1
> > sym0: No NVRAM, ID 7, Fast-20, SE, parity checking
> > sym1: <875> port 0x7400-0x74ff mem
> > 0x40101000-0x40101fff,0x40102100-0x401021ff irq 5 at device 8.0 on
> > pci1
> > sym1: No NVRAM, ID 7, Fast-20, SE, parity checking
> > pci1: <Cirrus Logic GD5430 SVGA controller> at 9.0
> > tl0: <Compaq NetFlex-3/P Integrated> port 0x6000-0x600f mem
> > 0x40000000-0x4000000f irq 9 at device 16.0 on pci0
> > tl0: Ethernet address: 00:80:5f:35:d8:6d
> > miibus0: <MII bus> on tl0
> > tlphy0: <ThunderLAN 10baseT media interface> on miibus0
> > tlphy0:  10base2/BNC, 10base5/AUI, 10baseT, 10baseT-FDX, auto
> > isab0: <Intel 82371SB PCI to ISA bridge> at device 20.0 on pci0
> > isa0: <ISA bus> on isab0
> > atapci0: <Intel PIIX3 ATA controller> port 0xf100-0xf10f at device
> > 20.1
> > on pci0
> > ata0: at 0x1f0 irq 14 on atapci0
> > ata1: at 0x170 irq 15 on atapci0
> > eisa0: <EISA bus> on motherboard
> > mainboard0: <CPQ0579 (System Board)> on eisa0 slot 0
> > orm0: <Option ROMs> at iomem
> > 0xc0000-0xc7fff,0xe8000-0xedfff,0xee000-0xeffff on isa0
> > pmtimer0 on isa0
> > pca0 at port 0x40 on isa0
> > fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2
> on
> > isa0
> > fdc0: FIFO enabled, 8 bytes threshold
> > fd0: <1440-KB 3.5" drive> on fdc0 drive 0
> > atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
> > atkbd0: <AT Keyboard> irq 1 on atkbdc0
> > kbd0 at atkbd0
> > psm0: <PS/2 Mouse> irq 12 on atkbdc0
> > psm0: model Generic PS/2 mouse, device ID 0
> > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff
> on
> > isa0
> > sc0: <System console> on isa0
> > sc0: VGA <16 virtual consoles, flags=0x200>
> > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
> > sio0: type 16550A
> > sio1 at port 0x2f8-0x2ff irq 3 on isa0
> > sio1: type 16550A
> > ppc0: cannot reserve I/O port range
> > IPsec: Initialized Security Association Processing.
> > ncp_load: [210-213]
> > ad1: 8207MB <ST38641A> [16676/16/63] at ata0-slave WDMA2
> > acd0: CDROM <HITACHI CDR-7930> at ata0-master PIO3
> > Waiting 15 seconds for SCSI devices to settle
> > Mounting root from ufs:/dev/da0s1a
> > da0 at sym1 bus 0 target 0 lun 0
> > da0: <COMPAQ ST34371W 0682> Fixed Direct Access SCSI-2 device
> > da0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged
> > Queueing
> > Enabled
> > da0: 4094MB (8386000 512 byte sectors: 255H 63S/T 522C)
> >
> 
> _______________________________________________
> freebsd-questions at freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-questions
> To unsubscribe, send any mail to
> "freebsd-questions-unsubscribe at freebsd.org"
> 
> _______________________________________________
> freebsd-questions at freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-questions
> To unsubscribe, send any mail to "freebsd-questions-unsubscribe at freebsd.org"