[axe][ue0] Device send packets but any host in network can not receive any packet from it.

[Perevalov Sergey]

Pyun YongHyeon, I am really sorry, I have found you message in my spam 
folder:-(
And immediately I did by your instructions.
I connected 2 Freebsd 8.0 hosts by one cable, and started tcpdump 
-evvvvvvi rl0/ue0.

So, 192.168.2.15 is receiver (rl0) log: http://pastebin.com/pZ5udweh

192.168.2.16 is sender (ue0) log: http://pastebin.com/BEDwUWBe

Thank you for your help!



On 08.05.2010 02:05, Pyun YongHyeon wrote:
> On Fri, May 07, 2010 at 10:30:21PM +0500, Perevalov Sergey wrote:
>    
>> Hi guys. I am beginner in FreeBSD.  And I got problem with my Gigabit
>> usb to ethernet adapter with AX88178 chipset. It works in windows very
>> well but doesn't work in FreeBSD 8.0. tcpdump shows log with received
>> and sent packets, but any host in network doesn't receive them from it.
>> I checked it with 2 FreeBSD hosts connected directly by cable. Can you,
>> guys, advice to me something to fix or to find reason of this issue?
>> I started thread on freebsd forums(
>> http://forums.freebsd.org/showthread.php?t=13649 ) and also reported
>> about problem ( http://www.freebsd.org/cgi/query-pr.cgi?pr=146153 ).
>>
>>      
> It seems the PR shows tcpdump output on sender side(axe(4)
> host 192.168.2.22). Would you capture the traffic on receiver side
> (host 192.168.2.7) and post the result? Note, please use direct
> cable to connect both systems and use option -e to capture traffic
> on host 192.168.2.7. For instance, use
> #ifconfig -envvvvvvi nic0
> on receiver side.
>
> Also check whether the receiver agrees on the resolved speed/duplex
> of established link. For your case, host 192.168.2.7 should show
> 100baseTX, full-duplex.
>
>    
>> Here some information:
>>
>> dmesg:
>> ugen4.2:<vendor 0x0b95>  at usbus4
>> axe0:<vendor 0x0b95 product 0x1780, rev 2.00/0.01, addr 2>  on usbus4
>> axe0: PHYADDR 0xe0:0x02
>> miibus0:<MII bus>  on axe0
>> rgephy0:<RTL8169S/8110S/8211B media interface>  PHY 2 on miibus0
>> rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
>> 1000baseT-FDX, auto
>> ue0:<USB Ethernet>  on axe0
>> ue0: Ethernet address: 00:0e:c6:88:09:4e
>>
>> usbconfig:
>> laptop# usbconfig
>> ugen0.1:<UHCI root HUB Intel>  at usbus0, cfg=0 md=HOST spd=FULL
>> (12Mbps) pwr=ON
>> ugen1.1:<UHCI root HUB Intel>  at usbus1, cfg=0 md=HOST spd=FULL
>> (12Mbps) pwr=ON
>> ugen2.1:<UHCI root HUB Intel>  at usbus2, cfg=0 md=HOST spd=FULL
>> (12Mbps) pwr=ON
>> ugen3.1:<UHCI root HUB Intel>  at usbus3, cfg=0 md=HOST spd=FULL
>> (12Mbps) pwr=ON
>> ugen4.1:<EHCI root HUB Intel>  at usbus4, cfg=0 md=HOST spd=HIGH
>> (480Mbps) pwr=ON
>> ugen4.2:<product 0x1780 vendor 0x0b95>  at usbus4, cfg=0 md=HOST
>> spd=HIGH (480Mbps) pwr=ON
>> ugen0.2:<Optical Mouse Genius>  at usbus0, cfg=0 md=HOST spd=LOW
>> (1.5Mbps) pwr=ON
>>
>> ifconfig:
>> ue0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST>  metric 0 mtu 1500
>> ether 00:0e:c6:88:09:4e
>> inet 192.168.2.22 netmask 0xffffff00 broadcast 192.168.2.255
>> media: Ethernet autoselect (100baseTX<full-duplex>)
>> status: active
>>
>> Thank you for you help!
>>      
>    


-- 
Regards, Sergey.