bce - status: no carrier - on Dell R900
Eduardo
sathler90 at gmail.com
Thu Dec 23 18:49:07 UTC 2010
Hi Folks,
I have a dell R900 - it came with a quad card Broadcom NetXtreme II
BCM5708 and I installed the 8.1 release amd64.
The bce connected to a switch foundry says 'no carrier', another bce
connected to a
router (juniper) works fine. I found some old threads about the bce driver.
http://www.freebsd.org/cgi/query-pr.cgi?pr=118238
and
http://unix.derkeiler.com/Mailing-Lists/FreeBSD/net/2007-11/msg00211.html
Below are boot messages regarding bce.
Any ideas on what I should try ? ( just now tried the 8.2 prerelease
0 - no luck)
thanks,
-Ed.
module_register: module bce/miibus already exists!
Module bce/miibus failed to register: 17
module_register: module pci/bce already exists!
Module pci/bce failed to register: 17
bce0: <Broadcom NetXtreme II BCM5708 1000Base-T (B2)> mem
0xd6000000-0xd7ffffff irq 18 at device 0.0 on pci11
miibus0: <MII bus> on bce0
bce0: Ethernet address: 00:26:b9:35:08:dc
bce0: [ITHREAD]
bce0: ASIC (0x57081020); Rev (B2); Bus (PCI-X, 64-bit, 133MHz); B/C
(5.0.4); Flags (MSI|MFW); MFW (ipms 1.6.0)
bce1: <Broadcom NetXtreme II BCM5708 1000Base-T (B2)> mem
0xd8000000-0xd9ffffff irq 19 at device 0.0 on pci9
miibus1: <MII bus> on bce1
bce1: Ethernet address: 00:26:b9:35:08:da
bce1: [ITHREAD]
bce1: ASIC (0x57081020); Rev (B2); Bus (PCI-X, 64-bit, 133MHz); B/C
(5.0.4); Flags (MSI|MFW); MFW (ipms 1.6.0)
bce2: <Broadcom NetXtreme II BCM5708 1000Base-T (B2)> mem
0xda000000-0xdbffffff irq 37 at device 0.0 on pci7
miibus2: <MII bus> on bce2
bce2: Ethernet address: 00:26:b9:35:08:d8
bce2: [ITHREAD]
bce2: ASIC (0x57081020); Rev (B2); Bus (PCI-X, 64-bit, 133MHz); B/C
(5.0.4); Flags (MSI|MFW); MFW (UMP 1.1.9)
bce3: <Broadcom NetXtreme II BCM5708 1000Base-T (B2)> mem
0xdc000000-0xddffffff irq 38 at device 0.0 on pci5
miibus3: <MII bus> on bce3
bce3: Ethernet address: 00:26:b9:35:08:d6
bce3: [ITHREAD]
bce3: ASIC (0x57081020); Rev (B2); Bus (PCI-X, 64-bit, 133MHz); B/C
(5.0.4); Flags (MSI|MFW); MFW (UMP 1.1.9)
bce0: bce_pulse(): Bootcode lost the driver pulse! (bc_state = 0x00002006)
bce1: bce_pulse(): Bootcode lost the driver pulse! (bc_state = 0x00002006)
bce2: bce_pulse(): Bootcode lost the driver pulse! (bc_state = 0x00004006)
bce3: bce_pulse(): Bootcode lost the driver pulse! (bc_state = 0x00004006)
and full dmesg:
Copyright (c) 1992-2010 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.1-RELEASE #0: Mon Jul 19 02:36:49 UTC 2010
root at mason.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC amd64
module_register: module bce/miibus already exists!
Module bce/miibus failed to register: 17
module_register: module pci/bce already exists!
Module pci/bce failed to register: 17
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Xeon(R) CPU E7440 @ 2.40GHz (2398.69-MHz K8-class CPU)
Origin = "GenuineIntel" Id = 0x106d1 Family = 6 Model = 1d Stepping = 1
Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0xce3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,DCA,SSE4.1>
AMD Features=0x20100800<SYSCALL,NX,LM>
AMD Features2=0x1<LAHF>
TSC: P-state invariant
real memory = 68719476736 (65536 MB)
avail memory = 66333831168 (63260 MB)
ACPI APIC Table: <DELL PE_SC3 >
FreeBSD/SMP: Multiprocessor System Detected: 16 CPUs
FreeBSD/SMP: 4 package(s) x 4 core(s)
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
cpu2 (AP): APIC ID: 2
cpu3 (AP): APIC ID: 3
cpu4 (AP): APIC ID: 8
cpu5 (AP): APIC ID: 9
cpu6 (AP): APIC ID: 10
cpu7 (AP): APIC ID: 11
cpu8 (AP): APIC ID: 16
cpu9 (AP): APIC ID: 17
cpu10 (AP): APIC ID: 18
cpu11 (AP): APIC ID: 19
cpu12 (AP): APIC ID: 24
cpu13 (AP): APIC ID: 25
cpu14 (AP): APIC ID: 26
cpu15 (AP): APIC ID: 27
ioapic0: Changing APIC ID to 6
ioapic1: Changing APIC ID to 7
ioapic0 <Version 2.0> irqs 0-23 on motherboard
ioapic1 <Version 2.0> irqs 32-55 on motherboard
kbd1 at kbdmux0
acpi0: <DELL PE_SC3> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <ACPI CPU> on acpi0
ACPI Warning for \\_PR_.CPU0._CST: Return Package is too small - found
3 elements, expected 3 (20100331/nspredef-787)
cpu0: invalid _CST state count (3 != 2)
cpu1: <ACPI CPU> on acpi0
ACPI Warning for \\_PR_.CPU1._CST: Return Package is too small - found
3 elements, expected 3 (20100331/nspredef-787)
cpu1: invalid _CST state count (3 != 2)
cpu2: <ACPI CPU> on acpi0
ACPI Warning for \\_PR_.CPU2._CST: Return Package is too small - found
3 elements, expected 3 (20100331/nspredef-787)
cpu2: invalid _CST state count (3 != 2)
cpu3: <ACPI CPU> on acpi0
ACPI Warning for \\_PR_.CPU3._CST: Return Package is too small - found
3 elements, expected 3 (20100331/nspredef-787)
cpu3: invalid _CST state count (3 != 2)
cpu4: <ACPI CPU> on acpi0
ACPI Warning for \\_PR_.CPU4._CST: Return Package is too small - found
3 elements, expected 3 (20100331/nspredef-787)
cpu4: invalid _CST state count (3 != 2)
cpu5: <ACPI CPU> on acpi0
ACPI Warning for \\_PR_.CPU5._CST: Return Package is too small - found
3 elements, expected 3 (20100331/nspredef-787)
cpu5: invalid _CST state count (3 != 2)
cpu6: <ACPI CPU> on acpi0
ACPI Warning for \\_PR_.CPU6._CST: Return Package is too small - found
3 elements, expected 3 (20100331/nspredef-787)
cpu6: invalid _CST state count (3 != 2)
cpu7: <ACPI CPU> on acpi0
ACPI Warning for \\_PR_.CPU7._CST: Return Package is too small - found
3 elements, expected 3 (20100331/nspredef-787)
cpu7: invalid _CST state count (3 != 2)
--More--(byte 3522) cpu13 (AP): APIC ID: 25
cpu14 (AP): APIC ID: 26
cpu15 (AP): APIC ID: 27
ioapic0: Changing APIC ID to 6
ioapic1: Changing APIC ID to 7
ioapic0 <Version 2.0> irqs 0-23 on motherboard
ioapic1 <Version 2.0> irqs 32-55 on motherboard
kbd1 at kbdmux0
acpi0: <DELL PE_SC3> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <ACPI CPU> on acpi0
ACPI Warning for \\_PR_.CPU0._CST: Return Package is too small - found
3 elements, expected 3 (20100331/nspredef-787)
cpu0: invalid _CST state count (3 != 2)
cpu1: <ACPI CPU> on acpi0
ACPI Warning for \\_PR_.CPU1._CST: Return Package is too small - found
3 elements, expected 3 (20100331/nspredef-787)
cpu1: invalid _CST state count (3 != 2)
cpu2: <ACPI CPU> on acpi0
ACPI Warning for \\_PR_.CPU2._CST: Return Package is too small - found
3 elements, expected 3 (20100331/nspredef-787)
cpu2: invalid _CST state count (3 != 2)
cpu3: <ACPI CPU> on acpi0
ACPI Warning for \\_PR_.CPU3._CST: Return Package is too small - found
3 elements, expected 3 (20100331/nspredef-787)
cpu3: invalid _CST state count (3 != 2)
cpu4: <ACPI CPU> on acpi0
ACPI Warning for \\_PR_.CPU4._CST: Return Package is too small - found
3 elements, expected 3 (20100331/nspredef-787)
cpu4: invalid _CST state count (3 != 2)
cpu5: <ACPI CPU> on acpi0
ACPI Warning for \\_PR_.CPU5._CST: Return Package is too small - found
3 elements, expected 3 (20100331/nspredef-787)
cpu5: invalid _CST state count (3 != 2)
cpu6: <ACPI CPU> on acpi0
ACPI Warning for \\_PR_.CPU6._CST: Return Package is too small - found
3 elements, expected 3 (20100331/nspredef-787)
cpu6: invalid _CST state count (3 != 2)
cpu7: <ACPI CPU> on acpi0
ACPI Warning for \\_PR_.CPU7._CST: Return Package is too small - found
3 elements, expected 3 (20100331/nspredef-787)
cpu7: invalid _CST state count (3 != 2)
cpu8: <ACPI CPU> on acpi0
ACPI Warning for \\_PR_.CPU8._CST: Return Package is too small - found
3 elements, expected 3 (20100331/nspredef-787)
cpu8: invalid _CST state count (3 != 2)
cpu9: <ACPI CPU> on acpi0
ACPI Warning for \\_PR_.CPU9._CST: Return Package is too small - found
3 elements, expected 3 (20100331/nspredef-787)
cpu9: invalid _CST state count (3 != 2)
cpu10: <ACPI CPU> on acpi0
ACPI Warning for \\_PR_.CP10._CST: Return Package is too small - found
3 elements, expected 3 (20100331/nspredef-787)
cpu10: invalid _CST state count (3 != 2)
cpu11: <ACPI CPU> on acpi0
ACPI Warning for \\_PR_.CP11._CST: Return Package is too small - found
3 elements, expected 3 (20100331/nspredef-787)
cpu11: invalid _CST state count (3 != 2)
cpu12: <ACPI CPU> on acpi0
ACPI Warning for \\_PR_.CP12._CST: Return Package is too small - found
3 elements, expected 3 (20100331/nspredef-787)
cpu12: invalid _CST state count (3 != 2)
cpu13: <ACPI CPU> on acpi0
ACPI Warning for \\_PR_.CP13._CST: Return Package is too small - found
3 elements, expected 3 (20100331/nspredef-787)
cpu13: invalid _CST state count (3 != 2)
cpu14: <ACPI CPU> on acpi0
ACPI Warning for \\_PR_.CP14._CST: Return Package is too small - found
3 elements, expected 3 (20100331/nspredef-787)
cpu14: invalid _CST state count (3 != 2)
cpu15: <ACPI CPU> on acpi0
ACPI Warning for \\_PR_.CP15._CST: Return Package is too small - found
3 elements, expected 3 (20100331/nspredef-787)
cpu15: invalid _CST state count (3 != 2)
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 900
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 36 at device 1.0 on pci0
pci20: <ACPI PCI bus> on pcib1
pcib2: <ACPI PCI-PCI bridge> irq 17 at device 2.0 on pci0
pci22: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> irq 17 at device 0.0 on pci22
pci23: <ACPI PCI bus> on pcib3
pcib4: <ACPI PCI-PCI bridge> irq 17 at device 0.0 on pci23
pci25: <ACPI PCI bus> on pcib4
mfi0: <Dell PERC 6> port 0xec00-0xecff mem
0xde380000-0xde3bffff,0xde3c0000-0xde3fffff irq 17 at device 0.0 on
pci25
mfi0: Megaraid SAS driver Ver 3.00
mfi0: 6684 (345318197s/0x0020/info) - Shutdown command received from host
mfi0: 6685 (boot + 3s/0x0020/info) - Firmware initialization started
(PCI ID 0060/1000/1f0c/1028)
mfi0: 6686 (boot + 3s/0x0020/info) - Firmware version 1.22.02-0612
mfi0: 6687 (boot + 23s/0x0008/info) - Battery Present
mfi0: 6688 (boot + 23s/0x0020/info) - Controller hardware revision ID (0x0)
mfi0: 6689 (boot + 23s/0x0020/info) - Package version 6.2.0-0013
mfi0: 6690 (boot + 23s/0x0020/info) - Board Revision
mfi0: 6691 (boot + 48s/0x0004/info) - Enclosure PD 20(c None/p0)
communication restored
mfi0: 6692 (boot + 49s/0x0002/info) - Inserted: Encl PD 20
mfi0: 6693 (boot + 49s/0x0002/info) - Inserted: PD 20(c None/p0) Info:
enclPd=20, scsiType=d, portMap=09,
sasAddr=5002609049922a00,0000000000000000
mfi0: 6694 (boot + 49s/0x0002/info) - Inserted: PD 00(e0x20/s0)
mfi0: 6695 (boot + 49s/0x0002/info) - Inserted: PD 00(e0x20/s0) Info:
enclPd=20, scsiType=0, portMap=00,
sasAddr=5000c50010012dd1,0000000000000000
mfi0: 6696 (boot + 49s/0x0002/info) - Inserted: PD 01(e0x20/s1)
mfi0: 6697 (boot + 49s/0x0002/info) - Inserted: PD 01(e0x20/s1) Info:
enclPd=20, scsiType=0, portMap=01,
sasAddr=5000c50010018bc1,0000000000000000
mfi0: 6698 (boot + 49s/0x0002/info) - Inserted: PD 02(e0x20/s2)
mfi0: 6699 (boot + 49s/0x0002/info) - Inserted: PD 02(e0x20/s2) Info:
enclPd=20, scsiType=0, portMap=02,
sasAddr=5000c50010012dad,0000000000000000
mfi0: 6700 (boot + 49s/0x0002/info) - Inserted: PD 03(e0x20/s3)
mfi0: 6701 (boot + 49s/0x0002/info) - Inserted: PD 03(e0x20/s3) Info:
enclPd=20, scsiType=0, portMap=03,
sasAddr=5000c50010012da9,0000000000000000
mfi0: 6702 (boot + 49s/0x0002/info) - Inserted: PD 04(e0x20/s4)
mfi0: 6703 (boot + 49s/0x0002/info) - Inserted: PD 04(e0x20/s4) Info:
enclPd=20, scsiType=0, portMap=04,
sasAddr=5000c50010012e3d,0000000000000000
mfi0: 6704 (345318253s/0x0020/info) - Time established as 12/10/10
17:44:13; (50 seconds since power on)
mfi0: 6705 (345318291s/0x0008/info) - Battery temperature is normal
mfi0: [ITHREAD]
pcib5: <ACPI PCI-PCI bridge> irq 18 at device 1.0 on pci23
pci24: <ACPI PCI bus> on pcib5
pcib6: <PCI-PCI bridge> at device 0.3 on pci22
pci26: <PCI bus> on pcib6
pcib7: <ACPI PCI-PCI bridge> irq 37 at device 3.0 on pci0
pci1: <ACPI PCI bus> on pcib7
pcib8: <ACPI PCI-PCI bridge> at device 0.0 on pci1
pci2: <ACPI PCI bus> on pcib8
pcib9: <PCI-PCI bridge> at device 1.0 on pci2
pci3: <PCI bus> on pcib9
pcib10: <ACPI PCI-PCI bridge> at device 2.0 on pci2
pci10: <ACPI PCI bus> on pcib10
pcib11: <ACPI PCI-PCI bridge> at device 0.0 on pci10
pci11: <ACPI PCI bus> on pcib11
bce0: <Broadcom NetXtreme II BCM5708 1000Base-T (B2)> mem
0xd6000000-0xd7ffffff irq 18 at device 0.0 on pci11
miibus0: <MII bus> on bce0
brgphy0: <BCM5708C 10/100/1000baseTX PHY> PHY 1 on miibus0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
bce0: Ethernet address: 00:26:b9:35:08:dc
bce0: [ITHREAD]
bce0: ASIC (0x57081020); Rev (B2); Bus (PCI-X, 64-bit, 133MHz); B/C
(5.0.4); Flags (MSI|MFW); MFW (ipms 1.6.0)
pcib12: <ACPI PCI-PCI bridge> at device 3.0 on pci2
pci8: <ACPI PCI bus> on pcib12
pcib13: <ACPI PCI-PCI bridge> at device 0.0 on pci8
pci9: <ACPI PCI bus> on pcib13
bce1: <Broadcom NetXtreme II BCM5708 1000Base-T (B2)> mem
0xd8000000-0xd9ffffff irq 19 at device 0.0 on pci9
miibus1: <MII bus> on bce1
brgphy1: <BCM5708C 10/100/1000baseTX PHY> PHY 1 on miibus1
brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
bce1: Ethernet address: 00:26:b9:35:08:da
bce1: [ITHREAD]
bce1: ASIC (0x57081020); Rev (B2); Bus (PCI-X, 64-bit, 133MHz); B/C
(5.0.4); Flags (MSI|MFW); MFW (ipms 1.6.0)
pcib14: <ACPI PCI-PCI bridge> at device 4.0 on pci2
pci6: <ACPI PCI bus> on pcib14
pcib15: <ACPI PCI-PCI bridge> at device 0.0 on pci6
pci7: <ACPI PCI bus> on pcib15
bce2: <Broadcom NetXtreme II BCM5708 1000Base-T (B2)> mem
0xda000000-0xdbffffff irq 37 at device 0.0 on pci7
miibus2: <MII bus> on bce2
brgphy2: <BCM5708C 10/100/1000baseTX PHY> PHY 1 on miibus2
brgphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
bce2: Ethernet address: 00:26:b9:35:08:d8
bce2: [ITHREAD]
bce2: ASIC (0x57081020); Rev (B2); Bus (PCI-X, 64-bit, 133MHz); B/C
(5.0.4); Flags (MSI|MFW); MFW (UMP 1.1.9)
pcib16: <ACPI PCI-PCI bridge> at device 5.0 on pci2
pci4: <ACPI PCI bus> on pcib16
pcib17: <ACPI PCI-PCI bridge> at device 0.0 on pci4
pci5: <ACPI PCI bus> on pcib17
bce3: <Broadcom NetXtreme II BCM5708 1000Base-T (B2)> mem
0xdc000000-0xddffffff irq 38 at device 0.0 on pci5
miibus3: <MII bus> on bce3
brgphy3: <BCM5708C 10/100/1000baseTX PHY> PHY 1 on miibus3
brgphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto
bce3: Ethernet address: 00:26:b9:35:08:d6
bce3: [ITHREAD]
bce3: ASIC (0x57081020); Rev (B2); Bus (PCI-X, 64-bit, 133MHz); B/C
(5.0.4); Flags (MSI|MFW); MFW (UMP 1.1.9)
pcib18: <ACPI PCI-PCI bridge> irq 32 at device 4.0 on pci0
pci12: <ACPI PCI bus> on pcib18
pcib19: <ACPI PCI-PCI bridge> at device 0.0 on pci12
pci13: <ACPI PCI bus> on pcib19
pcib20: <ACPI PCI-PCI bridge> at device 2.0 on pci13
pci15: <ACPI PCI bus> on pcib20
pcib21: <ACPI PCI-PCI bridge> at device 4.0 on pci13
pci14: <ACPI PCI bus> on pcib21
pcib22: <ACPI PCI-PCI bridge> irq 33 at device 6.0 on pci0
pci16: <ACPI PCI bus> on pcib22
pcib23: <ACPI PCI-PCI bridge> at device 0.0 on pci16
pci17: <ACPI PCI bus> on pcib23
pcib24: <ACPI PCI-PCI bridge> at device 2.0 on pci17
pci19: <ACPI PCI bus> on pcib24
pcib25: <ACPI PCI-PCI bridge> at device 4.0 on pci17
pci18: <ACPI PCI bus> on pcib25
pcib26: <ACPI PCI-PCI bridge> at device 28.0 on pci0
pci21: <ACPI PCI bus> on pcib26
uhci0: <Intel 631XESB/632XESB/3100 USB controller USB-1> port
0xcc80-0xcc9f irq 20 at device 29.0 on pci0
uhci0: [ITHREAD]
usbus0: <Intel 631XESB/632XESB/3100 USB controller USB-1> on uhci0
uhci1: <Intel 631XESB/632XESB/3100 USB controller USB-2> port
0xcca0-0xccbf irq 20 at device 29.1 on pci0
uhci1: [ITHREAD]
usbus1: <Intel 631XESB/632XESB/3100 USB controller USB-2> on uhci1
uhci2: <Intel 631XESB/632XESB/3100 USB controller USB-3> port
0xccc0-0xccdf irq 20 at device 29.2 on pci0
uhci2: [ITHREAD]
usbus2: <Intel 631XESB/632XESB/3100 USB controller USB-3> on uhci2
uhci3: <Intel 631XESB/632XESB/3100 USB controller USB-4> port
0xcce0-0xccff irq 20 at device 29.3 on pci0
uhci3: [ITHREAD]
usbus3: <Intel 631XESB/632XESB/3100 USB controller USB-4> on uhci3
ehci0: <Intel 63XXESB USB 2.0 controller> mem 0xde0ffc00-0xde0fffff
irq 21 at device 29.7 on pci0
ehci0: [ITHREAD]
usbus4: EHCI version 1.0
usbus4: <Intel 63XXESB USB 2.0 controller> on ehci0
pcib27: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci27: <ACPI PCI bus> on pcib27
vgapci0: <VGA-compatible display> port 0xdc00-0xdcff mem
0xc8000000-0xcfffffff,0xde4f0000-0xde4fffff irq 17 at device 12.0 on
pci27
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel 63XXESB2 SATA300 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfc00-0xfc0f at device 31.2 on
pci0
ata0: <ATA channel 0> on atapci0
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
ata1: [ITHREAD]
atrtc0: <AT realtime clock> port 0x70-0x7f irq 8 on acpi0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
uart0: [FILTER]
uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
uart1: [FILTER]
orm0: <ISA Option ROMs> at iomem
0xc0000-0xc8fff,0xc9000-0xc9fff,0xca000-0xcbfff,0xec000-0xeffff on
isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
ppc0: cannot reserve I/O port range
est0: <Enhanced SpeedStep Frequency Control> on cpu0
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 91e091e0800091e
device_attach: est0 attach returned 6
p4tcc0: <CPU Frequency Thermal Control> on cpu0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 91e091e0800091e
device_attach: est1 attach returned 6
p4tcc1: <CPU Frequency Thermal Control> on cpu1
est2: <Enhanced SpeedStep Frequency Control> on cpu2
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 91e091e0800091e
device_attach: est2 attach returned 6
p4tcc2: <CPU Frequency Thermal Control> on cpu2
est3: <Enhanced SpeedStep Frequency Control> on cpu3
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 91e091e0800091e
device_attach: est3 attach returned 6
p4tcc3: <CPU Frequency Thermal Control> on cpu3
est4: <Enhanced SpeedStep Frequency Control> on cpu4
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 91e091e0800091e
device_attach: est4 attach returned 6
p4tcc4: <CPU Frequency Thermal Control> on cpu4
est5: <Enhanced SpeedStep Frequency Control> on cpu5
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 91e091e0800091e
device_attach: est5 attach returned 6
p4tcc5: <CPU Frequency Thermal Control> on cpu5
est6: <Enhanced SpeedStep Frequency Control> on cpu6
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 91e091e0800091e
device_attach: est6 attach returned 6
p4tcc6: <CPU Frequency Thermal Control> on cpu6
est7: <Enhanced SpeedStep Frequency Control> on cpu7
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 91e091e0800091e
device_attach: est7 attach returned 6
p4tcc7: <CPU Frequency Thermal Control> on cpu7
est8: <Enhanced SpeedStep Frequency Control> on cpu8
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 91e091e0800091e
device_attach: est8 attach returned 6
p4tcc8: <CPU Frequency Thermal Control> on cpu8
est9: <Enhanced SpeedStep Frequency Control> on cpu9
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 91e091e0800091e
device_attach: est9 attach returned 6
p4tcc9: <CPU Frequency Thermal Control> on cpu9
est10: <Enhanced SpeedStep Frequency Control> on cpu10
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 91e091e0800091e
device_attach: est10 attach returned 6
p4tcc10: <CPU Frequency Thermal Control> on cpu10
est11: <Enhanced SpeedStep Frequency Control> on cpu11
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 91e091e0800091e
device_attach: est11 attach returned 6
p4tcc11: <CPU Frequency Thermal Control> on cpu11
est12: <Enhanced SpeedStep Frequency Control> on cpu12
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 91e091e0800091e
device_attach: est12 attach returned 6
p4tcc12: <CPU Frequency Thermal Control> on cpu12
est13: <Enhanced SpeedStep Frequency Control> on cpu13
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 91e091e0800091e
device_attach: est13 attach returned 6
p4tcc13: <CPU Frequency Thermal Control> on cpu13
est14: <Enhanced SpeedStep Frequency Control> on cpu14
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 91e091e0800091e
device_attach: est14 attach returned 6
p4tcc14: <CPU Frequency Thermal Control> on cpu14
est15: <Enhanced SpeedStep Frequency Control> on cpu15
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 91e091e0800091e
device_attach: est15 attach returned 6
p4tcc15: <CPU Frequency Thermal Control> on cpu15
Timecounters tick every 1.000 msec
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 480Mbps High Speed USB v2.0
ugen0.1: <Intel> at usbus0
uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <Intel> at usbus2
uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
ugen3.1: <Intel> at usbus3
uhub3: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
ugen4.1: <Intel> at usbus4
uhub4: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus4
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub2: 2 ports with 2 removable, self powered
uhub3: 2 ports with 2 removable, self powered
bce0: bce_pulse(): Bootcode lost the driver pulse! (bc_state = 0x00002006)
bce1: bce_pulse(): Bootcode lost the driver pulse! (bc_state = 0x00002006)
bce2: bce_pulse(): Bootcode lost the driver pulse! (bc_state = 0x00004006)
bce3: bce_pulse(): Bootcode lost the driver pulse! (bc_state = 0x00004006)
acd0: DVDROM <TSSTcorpDVD-ROM TS-L333A/D450> at ata0-master UDMA33 SATA
mfi0: 6706 (345318291s/0x0008/info) - Current capacity of the battery
is above threshold
mfid0: <MFI Logical Disk> on mfi0
mfid0: 953344MB (1952448512 sectors) RAID volume 'root' is optimal
mfid1: <MFI Logical Disk> on mfi0
mfid1: 953344MB (1952448512 sectors) RAID volume 'storage' is optimal
mfid2: <MFI Logical Disk> on mfi0
mfid2: 953344MB (1952448512 sectors) RAID volume 'ports' is optimal
SMP: AP CPU #1 Launched!
SMP: AP CPU #9 Launched!
SMP: AP CPU #12 Launched!
SMP: AP CPU #4 Launched!
SMP: AP CPU #8 Launched!
SMP: AP CPU #13 Launched!
SMP: AP CPU #2 Launched!
SMP: AP CPU #10 Launched!
SMP: AP CPU #3 Launched!
SMP: AP CPU #15 Launched!
SMP: AP CPU #11 Launched!
SMP: AP CPU #6 Launched!
SMP: AP CPU #7 Launched!
SMP: AP CPU #14 Launched!
SMP: AP CPU #5 Launched!
Root mount waiting for: usbus4
uhub4: 8 ports with 8 removable, self powered
ugen4.2: <vendor 0x413c> at usbus4
uhub5: <vendor 0x413c product 0xa001, class 9/0, rev 2.00/0.00, addr
2> on usbus4
uhub5: 2 ports with 2 removable, self powered
Root mount waiting for: usbus4
ugen4.3: <Dell> at usbus4
ukbd0: <Keyboard> on usbus4
kbd2 at ukbd0
ums0: <Mouse> on usbus4
ums0: 3 buttons and [Z] coordinates ID=0
ugen4.4: <vendor 0x04b4> at usbus4
uhub6: <vendor 0x04b4 product 0x6560, class 9/0, rev 2.00/90.15, addr
4> on usbus4
Root mount waiting for: usbus4
uhub6: 2 ports with 2 removable, self powered
ugen1.2: <NOVATEK> at usbus1
ukbd1: <NOVATEK USB Multimedia Keyboard, class 0/0, rev 1.10/1.00,
addr 2> on usbus1
kbd3 at ukbd1
uhid0: <NOVATEK USB Multimedia Keyboard, class 0/0, rev 1.10/1.00,
addr 2> on usbus1
ugen4.5: <vendor 0x04b4> at usbus4
uhub7: <vendor 0x04b4 product 0x6560, class 9/0, rev 2.00/90.15, addr
5> on usbus4
uhub7: 2 ports with 2 removable, self powered
Trying to mount root from ufs:/dev/mfid0s1a
bce1: link state changed to UP
mfi0: 6707 (345318356s/0x0008/info) - Battery started charging
mfi0: 6708 (345318421s/0x0008/info) - Battery charge complete
More information about the freebsd-net
mailing list