No sound with M-AUDIO DELTA 1010LT and snd_envy24
Dominique Goncalves
dominique.goncalves at gmail.com
Sun Nov 2 13:02:16 PST 2008
Hi,
I use FreeBSD 7.1-PRERELEASE and a M-AUDIO DELTA 1010LT sound card.
The sound card seems to be detected correctly but there is no sound
(It works on Windows XP and Ubuntu 7.10, it's not a problem of setup
with cable). By the way I use the analog output (1 and 2).
I tried with mplayer, it plays correctly without error but no sound.
%cat /boot/kernel/kernel > /dev/dsp0.0
load: 0.57 cmd: cat 2184 [pcmwr] 0.00u 0.00s 0% 772k
^C
It produce also no sound.
Is there a problem with my configuration or no support in
snd_envy24(4) for my sound card ?
Envy24Control [1] from ALSA project helps a lot to configure this
sound card, is there an alternative in FreeBSD?
[1] http://alsa.opensrc.org/Envy24Control
Thanks for your help,
Regards.
%sysctl hw.snd
hw.snd.latency_profile: 1
hw.snd.latency: 5
hw.snd.report_soft_formats: 1
hw.snd.compat_linux_mmap: 0
hw.snd.feeder_buffersize: 16384
hw.snd.feeder_rate_round: 25
hw.snd.feeder_rate_max: 2016000
hw.snd.feeder_rate_min: 1
hw.snd.verbose: 1
hw.snd.maxautovchans: 16
hw.snd.default_unit: 0
hw.snd.version: 2007061600/i386
hw.snd.default_auto: 0
%mixer
Mixer vol is currently set to 78:78
Mixer bass is currently set to 0:0
Mixer treble is currently set to 0:0
Mixer synth is currently set to 0:0
Mixer pcm is currently set to 81:81
Mixer speaker is currently set to 0:0
Mixer line is currently set to 75:75
Mixer mic is currently set to 0:0
Mixer cd is currently set to 0:0
Mixer mix is currently set to 0:0
Recording source: mic
%mixer speaker 50:50
Setting the mixer speaker from 0:0 to 50:50.
mixer: WRITE_MIXER: Device not configured
%kldstat
Id Refs Address Size Name
1 16 0xc0400000 97d3ac kernel
2 1 0xc0d7e000 90d0 snd_envy24.ko
3 4 0xc0d88000 4a62c sound.ko
4 2 0xc0dd3000 2a58 snd_spicds.ko
5 1 0xc0dd6000 6f88 snd_ich.ko
6 1 0xc0ddd000 4d20 atapicam.ko
7 1 0xc0de2000 6a2c4 acpi.ko
8 1 0xc413d000 21000 radeon.ko
9 1 0xc415e000 f000 drm.ko
10 1 0xc4a67000 7000 udf.ko
%pciconf -vl
hostb0 at pci0:0:0:0: class=0x060000 card=0x00000000 chip=0x06461039
rev=0x00 hdr=0x00
vendor = 'Silicon Integrated Systems (SiS)'
device = 'SiS645DX Host-to-PCI Bridge'
class = bridge
subclass = HOST-PCI
pcib1 at pci0:0:1:0: class=0x060400 card=0x00000000 chip=0x00011039
rev=0x00 hdr=0x01
vendor = 'Silicon Integrated Systems (SiS)'
device = 'SiS730 Virtual PCI-to-PCI bridge (AGP)'
class = bridge
subclass = PCI-PCI
isab0 at pci0:0:2:0: class=0x060100 card=0x00000000 chip=0x00081039
rev=0x04 hdr=0x00
vendor = 'Silicon Integrated Systems (SiS)'
device = 'SiS PCI to ISA Bridge (LPC Bridge)'
class = bridge
subclass = PCI-ISA
atapci0 at pci0:0:2:5: class=0x010180 card=0x55131039 chip=0x55131039
rev=0x00 hdr=0x00
vendor = 'Silicon Integrated Systems (SiS)'
device = 'SiS5513 EIDE Controller (A,B step)'
class = mass storage
subclass = ATA
ohci0 at pci0:0:3:0: class=0x0c0310 card=0x56701462 chip=0x70011039
rev=0x0f hdr=0x00
vendor = 'Silicon Integrated Systems (SiS)'
device = 'SiS5597/8 Universal Serial Bus Controller'
class = serial bus
subclass = USB
ohci1 at pci0:0:3:1: class=0x0c0310 card=0x56701462 chip=0x70011039
rev=0x0f hdr=0x00
vendor = 'Silicon Integrated Systems (SiS)'
device = 'SiS5597/8 Universal Serial Bus Controller'
class = serial bus
subclass = USB
ohci2 at pci0:0:3:2: class=0x0c0310 card=0x56701462 chip=0x70011039
rev=0x0f hdr=0x00
vendor = 'Silicon Integrated Systems (SiS)'
device = 'SiS5597/8 Universal Serial Bus Controller'
class = serial bus
subclass = USB
ehci0 at pci0:0:3:3: class=0x0c0320 card=0x56701462 chip=0x70021039
rev=0x00 hdr=0x00
vendor = 'Silicon Integrated Systems (SiS)'
device = 'SiS7002 USB 2.0 Enhanced Host Controller'
class = serial bus
subclass = USB
pcm0 at pci0:0:8:0: class=0x040100 card=0xd63b1412 chip=0x17121412
rev=0x02 hdr=0x00
vendor = 'VIA Technologies Inc (Was: IC Ensemble Inc)'
device = 'ICE1712 Envy24 Multichannel Audio Controller'
class = multimedia
subclass = audio
rl0 at pci0:0:11:0: class=0x020000 card=0x813910ec chip=0x813910ec
rev=0x10 hdr=0x00
vendor = 'Realtek Semiconductor'
device = 'RT8139 (A/B/C/810x/813x/C+) Fast Ethernet Adapter'
class = network
subclass = ethernet
vgapci0 at pci0:1:0:0: class=0x030000 card=0x7194174b chip=0x49661002
rev=0x01 hdr=0x00
vendor = 'ATI Technologies Inc'
device = 'RV250 Radeon 9000/9000 Pro'
class = display
subclass = VGA
Copyright (c) 1992-2008 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.1-PRERELEASE #0: Fri Sep 26 23:16:45 CEST 2008
root at djdomics:/usr/obj/usr/src/sys/GENERIC
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0e4e000.
Preloaded elf module "/boot/kernel/snd_envy24.ko" at 0xc0e4e1a8.
Preloaded elf module "/boot/kernel/sound.ko" at 0xc0e4e258.
Preloaded elf module "/boot/kernel/snd_spicds.ko" at 0xc0e4e304.
Preloaded elf module "/boot/kernel/snd_ich.ko" at 0xc0e4e3b4.
Preloaded elf module "/boot/kernel/atapicam.ko" at 0xc0e4e460.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0e4e510.
Calibrating clock(s) ... i8254 clock: 1193167 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 2000146912 Hz
CPU: Intel(R) Pentium(R) 4 CPU 2.00GHz (2000.15-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf24 Stepping = 4
Features=0x3febfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM>
Instruction TLB: 4 KB, 2 MB or 4 MB pages, fully associative, 64 entries
Data TLB: 4 KB or 4 MB pages, fully associative, 64 entries
1st-level data cache: 8 KB, 4-way set associative, sectored cache, 64
byte line size
Trace cache: 12K-uops, 8-way set associative
2nd-level cache: 512 KB, 8-way set associative, sectored cache, 64
byte line size
real memory = 805240832 (767 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000001025000 - 0x000000002f229fff, 773869568 bytes (188933 pages)
avail memory = 773971968 (738 MB)
Table 'FACP' at 0x2fff0030
Table 'APIC' at 0x2fff00c0
MADT: Found table at 0x2fff00c0
MP Configuration Table version 1.4 found at 0xc00f61f0
APIC: Using the MADT enumerator.
MADT: Found CPU APIC ID 0 ACPI ID 1: enabled
SMP: Added CPU 0 (AP)
ACPI APIC Table: <AMIINT SiS645XX>
bios32: Found BIOS32 Service Directory header at 0xc00fdb00
bios32: Entry = 0xfdb10 (c00fdb10) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0xdb31
pnpbios: Found PnP BIOS data at 0xc00f74a0
pnpbios: Entry = f0000:642b Rev = 1.0
Other BIOS signatures found:
APIC: CPU 0 has ACPI ID 1
ULE: setup cpu group 0
ULE: setup cpu 0
ULE: adding cpu 0 to group 0: cpus 1 mask 0x1
ACPI: RSDP @ 0x0xfa170/0x0014 (v 0 AMI )
ACPI: RSDT @ 0x0x2fff0000/0x002C (v 1 AMIINT SiS645XX 0x00000010 MSFT
0x0100000B)
ACPI: FACP @ 0x0x2fff0030/0x0081 (v 1 AMIINT SiS645XX 0x00000011 MSFT
0x0100000B)
ACPI: DSDT @ 0x0x2fff0110/0x3588 (v 1 SiS 645 0x00001000 MSFT
0x0100000D)
ACPI: FACS @ 0x0x2fff8000/0x0040
ACPI: APIC @ 0x0x2fff00c0/0x0050 (v 1 AMIINT SiS645XX 0x00001000 MSFT
0x0100000B)
MADT: Found IO APIC ID 2, Interrupt 0 at 0xfec00000
ioapic0: Routing external 8259A's -> intpin 0
MADT: Interrupt override: source 0, irq 2
ioapic0: Routing IRQ 0 -> intpin 2
lapic0: Routing NMI -> LINT1
lapic0: LINT1 trigger: edge
lapic0: LINT1 polarity: high
MADT: Forcing active-low polarity and level trigger for SCI
ioapic0: intpin 9 polarity: low
ioapic0: intpin 9 trigger: level
ioapic0 <Version 1.1> irqs 0-23 on motherboard
cpu0 BSP:
ID: 0x00000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000100ef therm: 0x00010000 err: 0x0001000f pcm: 0x00010000
snd_unit_init() u=0x00ff8000 [512] d=0x00007c00 [32] c=0x000003ff [1024]
feeder_register: snd_unit=-1 snd_maxautovchans=16 latency=5
feeder_buffersize=16384 feeder_rate_min=1 feeder_rate_max=2016000
feeder_rate_round=25
ath_rate: version 1.2 <SampleRate bit-rate selection algorithm>
wlan_amrr: <AMRR Transmit Rate Control Algorithm>
wlan: <802.11 Link Layer>
random: <entropy source, Software, Yarrow>
nfslock: pseudo-device
io: <I/O>
kbd: new array size 4
kbd1 at kbdmux0
mem: <memory>
Pentium Pro MTRR support enabled
null: <null device, zero device>
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
hptrr: RocketRAID 17xx/2xxx SATA controller driver v1.2 (Sep 26 2008 23:16:12)
npx0: INT 16 interface
acpi0: <AMIINT SiS645XX> on motherboard
ioapic0: routing intpin 9 (ISA IRQ 9) to vector 48
acpi0: [MPSAFE]
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
acpi0: wakeup code va 0xd30d6000 pa 0x1000
pci_open(1): mode 1 addr port (0x0cf8) is 0x00000208
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=80] is there (id=06461039)
pcibios: BIOS version 2.10
AcpiOsDerivePciId: \\_SB_.PCI0.TMEM -> bus 0 dev 0 func 0
AcpiOsDerivePciId: \\_SB_.PCI0.SBRG.PIX0 -> bus 0 dev 2 func 0
AcpiOsDerivePciId: \\_SB_.PCI0.SBRG.PIX1 -> bus 0 dev 2 func 0
ACPI timer: 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 -> 10
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
pci_link0: Index IRQ Rtd Ref IRQs
Initial Probe 0 11 N 0 3 4 5 7 10 11 12 14 15
Validation 0 11 N 0 3 4 5 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 10 11 12 14 15
pci_link1: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 7 10 11 12 14 15
Validation 0 255 N 0 3 4 5 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 10 11 12 14 15
pci_link2: Index IRQ Rtd Ref IRQs
Initial Probe 0 11 N 0 3 4 5 7 10 11 12 14 15
Validation 0 11 N 0 3 4 5 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 10 11 12 14 15
pci_link3: Index IRQ Rtd Ref IRQs
Initial Probe 0 12 N 0 3 4 5 7 10 11 12 14 15
Validation 0 12 N 0 3 4 5 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 10 11 12 14 15
pci_link4: Index IRQ Rtd Ref IRQs
Initial Probe 0 10 N 0 3 4 5 7 10 11 12 14 15
Validation 0 10 N 0 3 4 5 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 10 11 12 14 15
pci_link5: Index IRQ Rtd Ref IRQs
Initial Probe 0 10 N 0 3 4 5 7 10 11 12 14 15
Validation 0 10 N 0 3 4 5 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 10 11 12 14 15
pci_link6: Index IRQ Rtd Ref IRQs
Initial Probe 0 12 N 0 3 4 5 7 10 11 12 14 15
Validation 0 12 N 0 3 4 5 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 10 11 12 14 15
pci_link7: Index IRQ Rtd Ref IRQs
Initial Probe 0 10 N 0 3 4 5 7 10 11 12 14 15
Validation 0 10 N 0 3 4 5 7 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 7 10 11 12 14 15
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: domain=0, physical bus=0
found-> vendor=0x1039, dev=0x0646, revid=0x00
domain=0, bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x2210, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type Memory, range 32, base 0xe0000000, size 26, enabled
found-> vendor=0x1039, dev=0x0001, revid=0x00
domain=0, bus=0, slot=1, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x0000, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x0a (2500 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1039, dev=0x0008, revid=0x04
domain=0, bus=0, slot=2, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x000f, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1039, dev=0x5513, revid=0x00
domain=0, bus=0, slot=2, func=5
class=01-01-80, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x80 (3840 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[20]: type I/O Port, range 32, base 0xff00, size 4, enabled
found-> vendor=0x1039, dev=0x7001, revid=0x0f
domain=0, bus=0, slot=3, func=0
class=0c-03-10, hdrtype=0x00, mfdev=1
cmdreg=0x0117, statreg=0x0280, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x50 (20000 ns)
intpin=a, irq=10
map[10]: type Memory, range 32, base 0xdfffc000, size 12, enabled
pcib0: matched entry for 0.3.INTA
pcib0: slot 3 INTA hardwired to IRQ 20
found-> vendor=0x1039, dev=0x7001, revid=0x0f
domain=0, bus=0, slot=3, func=1
class=0c-03-10, hdrtype=0x00, mfdev=0
cmdreg=0x0117, statreg=0x0280, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x50 (20000 ns)
intpin=b, irq=10
map[10]: type Memory, range 32, base 0xdfffd000, size 12, enabled
pcib0: matched entry for 0.3.INTB
pcib0: slot 3 INTB hardwired to IRQ 21
found-> vendor=0x1039, dev=0x7001, revid=0x0f
domain=0, bus=0, slot=3, func=2
class=0c-03-10, hdrtype=0x00, mfdev=0
cmdreg=0x0117, statreg=0x0280, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x50 (20000 ns)
intpin=c, irq=12
map[10]: type Memory, range 32, base 0xdfffe000, size 12, enabled
pcib0: matched entry for 0.3.INTC
pcib0: slot 3 INTC hardwired to IRQ 22
found-> vendor=0x1039, dev=0x7002, revid=0x00
domain=0, bus=0, slot=3, func=3
class=0c-03-20, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x50 (20000 ns)
intpin=d, irq=10
powerspec 2 supports D0 D3 current D0
map[10]: type Memory, range 32, base 0xdffff000, size 12, enabled
pcib0: matched entry for 0.3.INTD
pcib0: slot 3 INTD hardwired to IRQ 23
found-> vendor=0x1412, dev=0x1712, revid=0x02
domain=0, bus=0, slot=8, func=0
class=04-01-00, hdrtype=0x00, mfdev=0
cmdreg=0x0105, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=12
powerspec 1 supports D0 D2 D3 current D0
map[10]: type I/O Port, range 32, base 0xdc00, size 5, enabled
map[14]: type I/O Port, range 32, base 0xd800, size 4, enabled
map[18]: type I/O Port, range 32, base 0xd400, size 4, enabled
map[1c]: type I/O Port, range 32, base 0xd000, size 6, enabled
pcib0: matched entry for 0.8.INTA
pcib0: slot 8 INTA hardwired to IRQ 19
found-> vendor=0x10ec, dev=0x8139, revid=0x10
domain=0, bus=0, slot=11, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0107, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x20 (8000 ns), maxlat=0x40 (16000 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type I/O Port, range 32, base 0xcc00, size 8, enabled
map[14]: type Memory, range 32, base 0xdfffbf00, size 8, enabled
pcib0: matched entry for 0.11.INTA
pcib0: slot 11 INTA hardwired to IRQ 18
agp0: <SiS 645DX host to AGP bridge> on hostb0
hostb0: Reserved 0x4000000 bytes for rid 0x10 type 3 at 0xe0000000
agp0: allocating GATT for aperture of size 64M
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pcib1: domain 0
pcib1: secondary bus 1
pcib1: subordinate bus 2
pcib1: I/O decode 0xa000-0xafff
pcib1: memory decode 0xdfd00000-0xdfefffff
pcib1: prefetched decode 0xcfa00000-0xdfbfffff
pci1: <PCI bus> on pcib1
pci1: domain=0, physical bus=1
found-> vendor=0x1002, dev=0x4966, revid=0x01
domain=0, bus=1, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0187, statreg=0x02b0, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type Prefetchable Memory, range 32, base 0xd0000000, size 27, enabled
pcib1: requested memory range 0xd0000000-0xd7ffffff: good
map[14]: type I/O Port, range 32, base 0xa800, size 8, enabled
pcib1: requested I/O range 0xa800-0xa8ff: in range
map[18]: type Memory, range 32, base 0xdfef0000, size 16, enabled
pcib1: requested memory range 0xdfef0000-0xdfefffff: good
pcib0: matched entry for 0.1.INTA
pcib0: slot 1 INTA hardwired to IRQ 16
pcib1: slot 0 INTA is routed to irq 16
vgapci0: <VGA-compatible display> port 0xa800-0xa8ff mem
0xd0000000-0xd7ffffff,0xdfef0000-0xdfefffff irq 16 at device 0.0 on
pci1
isab0: <PCI-ISA bridge> at device 2.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <SiS 962/963 UDMA133 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xff00-0xff0f at device 2.5 on
pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xff00
ata0: <ATA channel 0> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=50
ata0: stat0=0x90 err=0x90 lsb=0x90 msb=0x90
ata0: stat0=0x90 err=0x90 lsb=0x90 msb=0x90
ata0: stat0=0x90 err=0x90 lsb=0x90 msb=0x90
ata0: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: stat1=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=50 stat1=50 devices=0x3<ATA_SLAVE,ATA_MASTER>
ioapic0: routing intpin 14 (ISA IRQ 14) to vector 49
ata0: [MPSAFE]
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=03 ostat0=50 ostat1=50
ata1: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: stat1=0x10 err=0x01 lsb=0x14 msb=0xeb
ata1: reset tp2 stat0=00 stat1=10 devices=0xc<ATAPI_SLAVE,ATAPI_MASTER>
ioapic0: routing intpin 15 (ISA IRQ 15) to vector 50
ata1: [MPSAFE]
ata1: [ITHREAD]
ohci0: <SiS 5571 USB controller> mem 0xdfffc000-0xdfffcfff irq 20 at
device 3.0 on pci0
ohci0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xdfffc000
ioapic0: routing intpin 20 (PCI IRQ 20) to vector 51
ohci0: [GIANT-LOCKED]
ohci0: [ITHREAD]
usb0: OHCI version 1.0, legacy support
usb0: <SiS 5571 USB controller> on ohci0
usb0: USB revision 1.0
uhub0: <SiS OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 2 ports with 2 removable, self powered
ohci1: <SiS 5571 USB controller> mem 0xdfffd000-0xdfffdfff irq 21 at
device 3.1 on pci0
ohci1: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xdfffd000
ioapic0: routing intpin 21 (PCI IRQ 21) to vector 52
ohci1: [GIANT-LOCKED]
ohci1: [ITHREAD]
usb1: OHCI version 1.0, legacy support
usb1: <SiS 5571 USB controller> on ohci1
usb1: USB revision 1.0
uhub1: <SiS OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 2 ports with 2 removable, self powered
ohci2: <SiS 5571 USB controller> mem 0xdfffe000-0xdfffefff irq 22 at
device 3.2 on pci0
ohci2: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xdfffe000
ioapic0: routing intpin 22 (PCI IRQ 22) to vector 53
ohci2: [GIANT-LOCKED]
ohci2: [ITHREAD]
usb2: OHCI version 1.0, legacy support
usb2: <SiS 5571 USB controller> on ohci2
usb2: USB revision 1.0
uhub2: <SiS OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb2
uhub2: 2 ports with 2 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xdffff000-0xdfffffff
irq 23 at device 3.3 on pci0
ehci0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xdffff000
ioapic0: routing intpin 23 (PCI IRQ 23) to vector 54
ehci0: [GIANT-LOCKED]
ehci0: [ITHREAD]
usb3: EHCI version 1.0
usb3: companion controllers, 2 ports each: usb0 usb1 usb2
usb3: <EHCI (generic) USB 2.0 controller> on ehci0
usb3: USB revision 2.0
uhub3: <SiS EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb3
uhub3: 6 ports with 6 removable, self powered
umass0: <Kingston DataTraveler 2.0, class 0/0, rev 2.00/2.00, addr 2> on uhub3
umass0:0:0:-1: Attached to scbus0
pcm0: <Envy24 audio (Generic)> port
0xdc00-0xdc1f,0xd800-0xd80f,0xd400-0xd40f,0xd000-0xd03f irq 19 at
device 8.0 on pci0
pcm0: Reserved 0x20 bytes for rid 0x10 type 4 at 0xdc00
pcm0: Reserved 0x10 bytes for rid 0x14 type 4 at 0xd800
pcm0: Reserved 0x10 bytes for rid 0x18 type 4 at 0xd400
pcm0: Reserved 0x40 bytes for rid 0x1c type 4 at 0xd000
ioapic0: routing intpin 19 (PCI IRQ 19) to vector 55
pcm0: [MPSAFE]
pcm0: [ITHREAD]
pcm0: system configuration
SubVendorID: 0xd63b, SubDeviceID: 0x1412
XIN2 Clock Source: 22.5792MHz(44.1kHz*512)
MPU-401 UART(s) #: 1
AC'97 codec: not exist
ADC #: 4
DAC #: 4
Multi-track converter type: I2S(96KHz support, 24bit resolution, ID#0x2)
S/PDIF(IN/OUT): 1/1 ID# 0x00
GPIO(mask/dir/state): 0x04/0xfb/0x7e
pcm0: Mixer "vol":
pcm0: Mixer "bass":
pcm0: Mixer "treble":
pcm0: Mixer "synth":
pcm0: Mixer "pcm":
pcm0: Mixer "speaker":
pcm0: Mixer "line":
pcm0: Mixer "mic":
pcm0: Mixer "cd":
pcm0: Mixer "mix":
pcm0: clone manager: deadline=750ms flags=0x8000001e
rl0: <RealTek 8139 10/100BaseTX> port 0xcc00-0xccff mem
0xdfffbf00-0xdfffbfff irq 18 at device 11.0 on pci0
rl0: Reserved 0x100 bytes for rid 0x10 type 4 at 0xcc00
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> PHY 0 on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: bpf attached
rl0: Ethernet address: 00:10:dc:82:9b:d2
ioapic0: routing intpin 18 (PCI IRQ 18) to vector 56
rl0: [MPSAFE]
rl0: [ITHREAD]
fdc0: <floppy drive controller> port 0x3f2-0x3f3,0x3f4-0x3f5,0x3f7 irq
6 drq 2 on acpi0
fdc0: ic_type 90 part_id 80
ioapic0: routing intpin 6 (ISA IRQ 6) to vector 57
fdc0: [FILTER]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0: irq maps: 0x1c01 0x1c11 0x1c01 0x1c01
sio0: irq maps: 0x1c01 0x1c11 0x1c01 0x1c01
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
ioapic0: routing intpin 4 (ISA IRQ 4) to vector 58
sio0: [FILTER]
sio1: irq maps: 0x1c01 0x1c09 0x1c01 0x1c01
sio1: irq maps: 0x1c01 0x1c09 0x1c01 0x1c01
sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
ioapic0: routing intpin 3 (ISA IRQ 3) to vector 59
sio1: [FILTER]
cpu0: <ACPI CPU> on acpi0
cpu0: switching to generic Cx mode
p4tcc0: <CPU Frequency Thermal Control> on cpu0
ahc_isa_probe 12: ioport 0xcc00 alloc failed
ahc_isa_probe 13: ioport 0xdc00 alloc failed
ex_isa_identify()
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
fdc: fdc0 already exists; skipping it
sio: sio0 already exists; skipping it
sio: sio1 already exists; skipping it
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
unknown: status reg test failed fe
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xccfff,0xcd000-0xcf7ff pnpid
ORM0000 on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
ioapic0: routing intpin 1 (ISA IRQ 1) to vector 60
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: current command byte:0065
psm0: strange result for test aux port (1).
psm0: failed to reset the aux device.
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
le0: not probed (disabled)
ppc0: parallel port found at 0x378
ppc0: using extended I/O port range
ppc0: EPP SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
ioapic0: routing intpin 7 (ISA IRQ 7) to vector 61
ppbus0: [MPSAFE]
ppbus0: [ITHREAD]
ppi0: <Parallel I/O> on ppbus0
plip0: <PLIP network interface> on ppbus0
plip0: WARNING: using obsoleted IFF_NEEDSGIANT flag
plip0: bpf attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppc0: [GIANT-LOCKED]
ppc0: [ITHREAD]
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd1, terminal emulator: sc (syscons terminal)
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
ums0: <Logitech USB Mouse, class 0/0, rev 1.10/6.10, addr 2> on uhub2
ums0: 3 buttons and Z dir.
Device configuration finished.
procfs registered
lapic: Divisor 2, Frequency 50003675 hz
Timecounter "TSC" frequency 2000146912 Hz quality 800
Timecounters tick every 1.000 msec
lo0: bpf attached
hptrr: no controller detected.
ata0-slave: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=80 wire
ata0-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=80 wire
atapicam: atapicam0 already exists; skipping it
ad0: setting PIO4 on 5513 chip
ad0: setting UDMA100 on 5513 chip
ad0: 57241MB <Seagate ST360012A 3.30> at ata0-master UDMA100
ad0: 117231408 sectors [28733C/16H/255S] 16 sectors/interrupt 1 depth queue
ad0: Silicon Integrated Systems check1 failed
ad0: Adaptec check1 failed
ad0: LSI (v3) check1 failed
ad0: LSI (v2) check1 failed
ad0: FreeBSD check1 failed
ad1: setting PIO4 on 5513 chip
ad1: setting UDMA100 on 5513 chip
ad1: 57241MB <Seagate ST360015A 3.33> at ata0-slave UDMA100
ad1: 117231408 sectors [28733C/16H/255S] 16 sectors/interrupt 1 depth queue
ad1: Silicon Integrated Systems check1 failed
ad1: Adaptec check1 failed
ad1: LSI (v3) check1 failed
ad1: LSI (v2) check1 failed
ad1: FreeBSD check1 failed
ata1-slave: pio=PIO4 wdma=WDMA2 udma=UDMA33 cable=80 wire
ata1-master: pio=PIO4 wdma=WDMA2 udma=UDMA33 cable=40 wire
acd0: setting PIO4 on 5513 chip
acd0: setting UDMA33 on 5513 chip
acd0: <HL-DT-STDVD-ROM GDR8161B/0100> DVDROM drive at ata1 as master
acd0: read 3445KB/s (8268KB/s), 256KB buffer, UDMA33
acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet
acd0: Writes:
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: DVD 120mm audio disc
acd1: setting PIO4 on 5513 chip
acd1: setting UDMA33 on 5513 chip
acd1: <HL-DT-ST GCE-8481B/1.00> CDRW drive at ata1 as slave
acd1: read 6890KB/s (6890KB/s) write 688KB/s (8268KB/s), 2048KB buffer, UDMA33
acd1: Reads: CDR, CDRW, CDDA stream, packet
acd1: Writes: CDR, CDRW, test write, burnproof
acd1: Audio: play, 255 volume levels
acd1: Mechanism: ejectable tray, unlocked
acd1: Medium: no/blank disc
GEOM: new disk ad0
GEOM: new disk ad1
GEOM_LABEL: Label for provider acd0 is iso9660/SOMETHING.
GEOM: new disk da0
pass0 at umass-sim0 bus 0 target 0 lun 0
pass0: <Kingston DataTraveler 2.0 1.00> Removable Direct Access SCSI-2 device
pass0: 40.000MB/s transfers
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <Kingston DataTraveler 2.0 1.00> Removable Direct Access SCSI-2 device
da0: 40.000MB/s transfers
da0: 1947MB (3987456 512 byte sectors: 255H 63S/T 248C)
ATA PseudoRAID loaded
acd1: FAILURE - INQUIRY ILLEGAL REQUEST asc=0x24 ascq=0x00
(probe2:ata1:0:1:0): error 22
(probe2:ata1:0:1:0): Unretryable Error
acd0: FAILURE - INQUIRY ILLEGAL REQUEST asc=0x24 ascq=0x00
(probe1:ata1:0:0:0): error 22
(probe1:ata1:0:0:0): Unretryable Error
pass1 at ata1 bus 0 target 1 lun 0
pass1: <HL-DT-ST CD-RW GCE-8481B 1.00> Removable CD-ROM SCSI-0 device
pass1: 33.000MB/s transfers
pass2 at ata1 bus 0 target 0 lun 0
pass2: <HL-DT-ST DVD-ROM GDR8161B 0100> Removable CD-ROM SCSI-0 device
pass2: 33.000MB/s transfers
(cd0:ata1:0:1:0): error 6
(cd0:ata1:0:1:0): Unretryable Error
cd0 at ata1 bus 0 target 1 lun 0
cd0: <HL-DT-ST CD-RW GCE-8481B 1.00> Removable CD-ROM SCSI-0 device
cd0: 33.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not
present - tray closed
cd1 at ata1 bus 0 target 0 lun 0
cd1: <HL-DT-ST DVD-ROM GDR8161B 0100> Removable CD-ROM SCSI-0 device
cd1: 33.000MB/s transfers
cd1: cd present [3837254 x 2048 byte records]
GEOM: new disk cd0
GEOM: new disk cd1
GEOM_LABEL: Label for provider da0s1 is msdosfs/ .
(cd0:ata1:0:1:0): error 6
(cd0:ata1:0:1:0): Unretryable Error
(cd0:ata1:0:1:0): error 6
(cd0:ata1:0:1:0): Unretryable Error
(cd0:ata1:0:1:0): error 6
(cd0:ata1:0:1:0): Unretryable Error
(cd0:ata1:0:1:0): error 6
(cd0:ata1:0:1:0): Unretryable Error
Trying to mount root from ufs:/dev/ad0s2a
start_init: trying /sbin/init
drm0: <ATI Radeon If RV250 9000> on vgapci0
info: [drm] AGP at 0xe0000000 64MB
info: [drm] Initialized radeon 1.25.0 20060524
vgapci0: Reserved 0x10000 bytes for rid 0x18 type 3 at 0xdfef0000
vgapci0: Reserved 0x8000000 bytes for rid 0x10 type 3 at 0xd0000000
agp0: Setting AGP v2 mode 4
info: [drm] Setting GART location based on new memory map
info: [drm] Loading R200 Microcode
info: [drm] writeback test succeeded in 1 usecs
ioapic0: routing intpin 16 (PCI IRQ 16) to vector 62
drm0: [MPSAFE]
drm0: [ITHREAD]
umass0: at uhub3 port 5 (addr 2) disconnected
(pass0:umass-sim0:0:0:0): lost device
(pass0:umass-sim0:0:0:0): removing device entry
(da0:umass-sim0:0:0:0): lost device
(da0:umass-sim0:0:0:0): removing device entry
GEOM_LABEL: Label msdosfs/ removed.
umass0: detached
umass0: <Kingston DataTraveler 2.0, class 0/0, rev 2.00/2.00, addr 2> on uhub3
umass0:0:0:-1: Attached to scbus0
pass0 at umass-sim0 bus 0 target 0 lun 0
pass0: <Kingston DataTraveler 2.0 1.00> Removable Direct Access SCSI-2 device
pass0: 40.000MB/s transfers
GEOM: new disk da0
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <Kingston DataTraveler 2.0 1.00> Removable Direct Access SCSI-2 device
da0: 40.000MB/s transfers
da0: 1947MB (3987456 512 byte sectors: 255H 63S/T 248C)
GEOM_LABEL: Label for provider da0s1 is msdosfs/ .
GEOM_LABEL: Label msdosfs/ removed.
GEOM_LABEL: Label for provider da0s1 is msdosfs/ .
GEOM_LABEL: Label msdosfs/ removed.
%
--
There's this old saying: "Give a man a fish, feed him for a day. Teach
a man to fish, feed him for life."
More information about the freebsd-multimedia
mailing list