Intel HDA (IDT 92HD73E) on a DPS45G audio problems.

Mon Dec 22 16:19:36 UTC 2008

I have a Intel DPS45G mainboard [1], running 7.1-PRERELEASE on it. When I load 
the snd_hda.ko the system will pick up the audio hardware as:
pcm0: <Intel (Unknown) High Definition Audio Controller> mem 
0xc3420000-0xc3423fff irq 22 at device 27.0 on pci0
pcm0: [ITHREAD]
pcm0: <HDA Codec: Unknown Codec>
pcm0: <HDA Driver Revision: 20080420_0052>
But no dsp nodes are created in /dev until I try to mplayer/sidplay something. 
Even so, I still hear nothing coming from my speakers. I've also tried cat 
some/wave/file > dev/dsp0.0 after the dsp0.0 node is created from running 
mplayer or sidplay.

Is this just a missing device definition somewhere?

cat /dev/sndstat:
FreeBSD Audio Driver (newpcm: 32bit 2007061600/i386)
Installed devices:
pcm0: <Intel (Unknown) High Definition Audio Controller> at memory 0xc3420000 
irq 22 kld snd_hda [20080420_0052] [MPSAFE] (1p:1v/1r:1v channels duplex 
default)

dmesg:
Copyright (c) 1992-2008 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.1-PRERELEASE #2: Tue Dec 23 01:44:32 WST 2008
    agh at madcat:/usr/obj/usr/src/sys/MADCAT
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Core(TM)2 Quad CPU    Q9650  @ 3.00GHz (2999.97-MHz 686-class 
CPU)
  Origin = "GenuineIntel"  Id = 0x1067a  Stepping = 10
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0x408e3fd<SSE3,DTES64,MON,DS_CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,<b26>>
  AMD Features=0x20100000<NX,LM>
  AMD Features2=0x1<LAHF>
  Logical CPUs per core: 4
real memory  = 2146435072 (2047 MB)
avail memory = 2088128512 (1991 MB)
MPTable: <DP45SG INTEL>
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
 cpu2 (AP): APIC ID:  2
 cpu3 (AP): APIC ID:  3
ioapic0: Assuming intbase of 0
ioapic0 <Version 2.0> irqs 0-23 on motherboard
kbd1 at kbdmux0
pcib0: <MPTable Host-PCI bridge> pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
pcib1: <PCI-PCI bridge> irq 16 at device 1.0 on pci0
pci1: <PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0xe000-0xe07f mem 
0xc2000000-0xc2ffffff,0xa0000000-0xbfffffff,0xc0000000-0xc1ffffff irq 16 at 
device 0.0 on pci1
nvidia0: <GeForce 8600 GT> on vgapci0
vgapci0: child nvidia0 requested pci_enable_busmaster
vgapci0: child nvidia0 requested pci_enable_io
nvidia0: [GIANT-LOCKED]
nvidia0: [ITHREAD]
pcib2: <PCI-PCI bridge> irq 16 at device 6.0 on pci0
pci2: <PCI bus> on pcib2
pcib3: <PCI-PCI bridge> at device 0.0 on pci2
pci3: <PCI bus> on pcib3
pcib4: <PCI-PCI bridge> at device 0.2 on pci2
pci4: <PCI bus> on pcib4
hptrr0: <sx508x> port 0xd000-0xd0ff mem 0xc3100000-0xc31fffff irq 16 at device 
4.0 on pci4
hptrr: adapter at PCI 4:4:0, IRQ 16
em0: <Intel(R) PRO/1000 Network Connection 6.9.6> port 0xf0e0-0xf0ff mem 
0xc3400000-0xc341ffff,0xc3424000-0xc3424fff irq 20 at device 25.0 on pci0
em0: Using MSI interrupt
em0: [FILTER]
em0: Ethernet address: 00:1c:c0:8c:09:75
uhci0: <UHCI (generic) USB controller> port 0xf0c0-0xf0df irq 16 at device 
26.0 on pci0
uhci0: [GIANT-LOCKED]
uhci0: [ITHREAD]
usb0: <UHCI (generic) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 2 ports with 2 removable, self powered
uhci1: <UHCI (generic) USB controller> port 0xf0a0-0xf0bf irq 21 at device 
26.1 on pci0
uhci1: [GIANT-LOCKED]
uhci1: [ITHREAD]
usb1: <UHCI (generic) USB controller> on uhci1
usb1: USB revision 1.0
uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 2 ports with 2 removable, self powered
uhci2: <UHCI (generic) USB controller> port 0xf080-0xf09f irq 18 at device 
26.2 on pci0
uhci2: [GIANT-LOCKED]
uhci2: [ITHREAD]
usb2: <UHCI (generic) USB controller> on uhci2
usb2: USB revision 1.0
uhub2: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb2
uhub2: 2 ports with 2 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xc3425400-0xc34257ff irq 18 at 
device 26.7 on pci0
ehci0: [GIANT-LOCKED]
ehci0: [ITHREAD]
usb3: waiting for BIOS to give up control
usb3: EHCI version 1.0
usb3: companion controllers, 2 ports each: usb0 usb1 usb2
usb3: <EHCI (generic) USB 2.0 controller> on ehci0
usb3: USB revision 2.0
uhub3: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb3
uhub3: 6 ports with 6 removable, self powered
pci0: <multimedia> at device 27.0 (no driver attached)
uhci3: <UHCI (generic) USB controller> port 0xf060-0xf07f irq 23 at device 
29.0 on pci0
uhci3: [GIANT-LOCKED]
uhci3: [ITHREAD]
usb4: <UHCI (generic) USB controller> on uhci3
usb4: USB revision 1.0
uhub4: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb4
uhub4: 2 ports with 2 removable, self powered
uhci4: <UHCI (generic) USB controller> port 0xf040-0xf05f irq 19 at device 
29.1 on pci0
uhci4: [GIANT-LOCKED]
uhci4: [ITHREAD]
usb5: <UHCI (generic) USB controller> on uhci4
usb5: USB revision 1.0
uhub5: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb5
uhub5: 2 ports with 2 removable, self powered
uhci5: <UHCI (generic) USB controller> port 0xf020-0xf03f irq 18 at device 
29.2 on pci0
uhci5: [GIANT-LOCKED]
uhci5: [ITHREAD]
usb6: <UHCI (generic) USB controller> on uhci5
usb6: USB revision 1.0
uhub6: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb6
uhub6: 2 ports with 2 removable, self powered
ehci1: <EHCI (generic) USB 2.0 controller> mem 0xc3425000-0xc34253ff irq 23 at 
device 29.7 on pci0
ehci1: [GIANT-LOCKED]
ehci1: [ITHREAD]
usb7: waiting for BIOS to give up control
usb7: timed out waiting for BIOS
usb7: EHCI version 1.0
usb7: companion controllers, 2 ports each: usb4 usb5 usb6
usb7: <EHCI (generic) USB 2.0 controller> on ehci1
usb7: USB revision 2.0
uhub7: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb7
uhub7: 6 ports with 6 removable, self powered
pcib5: <MPTable PCI-PCI bridge> at device 30.0 on pci0
pci5: <PCI bus> on pcib5
fwohci0: <Lucent FW322/323> mem 0xc3300000-0xc3300fff irq 19 at device 0.0 on 
pci5
fwohci0: [FILTER]
fwohci0: OHCI version 1.0 (ROM=0)
fwohci0: No. of Isochronous channels is 8.
fwohci0: EUI64 00:90:27:00:02:2b:34:b9
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:90:27:2b:34:b9
fwe0: Ethernet address: 02:90:27:2b:34:b9
dcons_crom0: <dcons configuration ROM> on firewire0
dcons_crom0: bus_addr 0x12d0000
fwip0: <IP over FireWire> on firewire0
fwip0: Firewire address: 00:90:27:00:02:2b:34:b9 @ 0xfffe00000000, S400, 
maxrec 2048
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH10 SATA300 controller> port 
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xf170-0xf17f,0xf160-0xf16f irq 19 at 
device 31.2 on pci0
ata0: <ATA channel 0> on atapci0
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
ata1: [ITHREAD]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
atapci1: <Intel ICH10 SATA300 controller> port 
0xf150-0xf157,0xf140-0xf143,0xf130-0xf137,0xf120-0xf123,0xf110-0xf11f,0xf100-0xf10f 
irq 19 at device 31.5 on pci0
atapci1: [ITHREAD]
ata2: <ATA channel 0> on atapci1
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci1
ata3: [ITHREAD]
cpu0 on motherboard
est0: <Enhanced SpeedStep Frequency Control> on cpu0
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 616092206000922
device_attach: est0 attach returned 6
p4tcc0: <CPU Frequency Thermal Control> on cpu0
cpu1 on motherboard
est1: <Enhanced SpeedStep Frequency Control> on cpu1
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 616092206000922
device_attach: est1 attach returned 6
p4tcc1: <CPU Frequency Thermal Control> on cpu1
cpu2 on motherboard
est2: <Enhanced SpeedStep Frequency Control> on cpu2
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 616092206000922
device_attach: est2 attach returned 6
p4tcc2: <CPU Frequency Thermal Control> on cpu2
cpu3 on motherboard
est3: <Enhanced SpeedStep Frequency Control> on cpu3
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 616092206000922
device_attach: est3 attach returned 6
p4tcc3: <CPU Frequency Thermal Control> on cpu3
orm0: <ISA Option ROMs> at iomem 0xc0000-0xccfff,0xcd000-0xd47ff pnpid ORM0000 
on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
ppc0: parallel port not found.
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio0: [FILTER]
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
uhub8: <ALCOR Generic USB Hub, class 9/0, rev 1.10/3.12, addr 2> on uhub0
uhub8: 4 ports with 4 removable, self powered
ukbd0: <DATACOMP SteelS????DATA, class 0/0, rev 1.10/0.01, addr 3> on uhub0
kbd2 at ukbd0
ums0: <DATACOMP SteelS????DATA, class 0/0, rev 1.10/0.01, addr 3> on uhub0
ums_attach: bLength=7 bDescriptorType=5 bEndpointAddress=2-in bmAttributes=3 
wMaxPacketSize=5 bInterval=10
ums0: mouse has no X report
device_attach: ums0 attach returned 6
Timecounters tick every 1.000 msec
hptrr: start channel [0,1]
hptrr: start channel [0,2]
hptrr: start channel [0,3]
hptrr: start channel [0,4]
hptrr: start channel [0,5]
hptrr: channel [0,1] started successfully
hptrr: channel [0,2] started successfully
hptrr: channel [0,3] started successfully
hptrr: channel [0,4] started successfully
hptrr: channel [0,5] started successfully
hptrr0: [GIANT-LOCKED]
hptrr0: [ITHREAD]
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
da0 at hptrr0 bus 0 target 0 lun 0
da0: <HPT DISK 0_0 4.00> Fixed Direct Access SCSI-0 device 
acd0: DVDR <PLEXTOR DVDR PX-716A/1.07> at ata0-master SATA150
acd0: FAILURE - INQUIRY ILLEGAL REQUEST asc=0x24 ascq=0x00 
ad6: 114473MB <Seagate ST3120026AS 3.05> at ata3-master SATA150
SMP: AP CPU #1 Launched!
SMP: AP CPU #3 Launched!
SMP: AP CPU #2 Launched!
cd0 at ata0 bus 0 target 0 lun 0
cd0: <PLEXTOR DVDR   PX-716A 1.07> Removable CD-ROM SCSI-0 device 
cd0: 3.300MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present - tray 
closed

-Alastair

[1] http://www.intel.com/products/desktop/motherboards/DP45SG/DP45SG-
overview.htm