BCM5836 D-Link DIR-330

Alexandr Rybalko ray at dlink.ua
Wed Jun 3 10:42:11 UTC 2009


Results the same as DIR-320, but bfe with different PHY (switch BCM5325E)
And different USB core.

entry: mips_init()
Cache info:
  picache_stride    = 4096
  picache_loopcount = 4
  pdcache_stride    = 4096
  pdcache_loopcount = 4
cpu0: Broadcom processor v6.144
  MMU: Standard TLB, 32 entries
  L1 i-cache: 2 ways of 512 sets, 16 bytes per line
  L1 d-cache: 2 ways of 512 sets, 16 bytes per line
  Config1=0x3ed96c82<EJTAG>
Va=0xc0000000 Ve=ffffc000
init kernel_segmap va >> = 768 nkpt:120
avail_start:0x419000 avail_end:0x2000000
KDB: debugger backends: ddb
KDB: current backend: ddb
hz=100 cyl_per_hz:132000 cyl_per_usec:132 freq:132000000 cyl_per_hz:1320000 cyl_per_sec:132000000
Copyright (c) 1992-2009 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.0-CURRENT #533 r120:192973MS: Wed Jun  3 12:33:29 EEST 2009
    root at terran.mk.farlep.net:/usr/home/ray/Projects/MIPS/FreeBSD/obj/mips/usr/home/ray/Projects/MIPS/FreeBSD/src/sys/BCM4704
real memory  = 32894976 (32124K bytes)
Physical memory chunk(s):
0x00419000 - 0x01f43fff, 28487680 bytes (6955 pages)
avail memory = 28135424 (26MB)
null: <null device, zero device>
nfslock: pseudo-device
mem: <memory>
nexus0: <MIPS32 root nexus>
clock0: <Generic MIPS32 ticker> on nexus0
clock0: [FILTER]
siba0: start 18000000 len 00010000
siba0: idlo = 100422dd
siba0: idhi = 42438003
siba0:  chipcore id = 00000800
siba0: ccid = 00094704, cc_id = 4704, cc_rev = 0009
siba0: 9 cores detected.
siba0: after remapping: start 18000000 len 00009000
siba0: <Sonics SiliconBackplane rev 0x0> at mem 0x18000000-0x18008fff on nexus0
siba_attach: entry
siba_setup_devinfo: core=0 Vendor=4243 Dev=800 Rev=003
siba0: <ChipCommon> corid=0800 regions count 4 0=18000000x1000 1=1fc00000x400000 2=1c000000x2000000 3=1a000000x2000000
siba_setup_devinfo: core=1 Vendor=4243 Dev=806 Rev=006
siba0: <Ethernet core> corid=0806 regions count 1 0=18001000x1000
siba_setup_devinfo: core=2 Vendor=4243 Dev=806 Rev=006
siba0: <Ethernet core> corid=0806 regions count 1 0=18002000x1000
siba_setup_devinfo: core=3 Vendor=4243 Dev=808 Rev=003
siba0: <USB host controller> corid=0808 regions count 1 0=18003000x1000
siba_setup_devinfo: core=4 Vendor=4243 Dev=804 Rev=008
siba0: <PCI host interface> corid=0804 regions count 3 0=18004000x1000 1=08000000x8000000 2=40000000x40000000
siba_setup_devinfo: core=5 Vendor=4243 Dev=816 Rev=003
siba0: <MIPS 3302 core> corid=0816 regions count 1 0=18005000x1000
siba_setup_devinfo: core=6 Vendor=4243 Dev=807 Rev=002
siba0: <V90 Codec Core> corid=0807 regions count 1 0=18006000x1000
siba_setup_devinfo: core=7 Vendor=4243 Dev=80b Rev=000
siba0: <IPSEC accelerator> corid=080b regions count 1 0=18007000x1000
siba_setup_devinfo: core=8 Vendor=4243 Dev=80f Rev=002
siba0: <SDRAM/DDR controller> corid=080f regions count 4 0=18008000x1000 1=00000000x8000000 2=10000000x8000000 3=80000000x20000000
siba_cc0: <ChipCommon core> at mem 0x18000000-0x18000fff irq 0 on siba0
siba_cc0: [FILTER]
siba_cc0: Core Revision 3
siba_cc0: Number of UARTs 2
siba_cc0: UARTs clock select 0x08
siba_cc0: UART use internal divided clock
siba_cc0: UART use GPIO pins 15:12
siba_cc0: PCMCIA, IDE & Prog
siba_cc0: Parallel flash
siba_cc0: Type of PLL 0x04
uart0: [FILTER]
uart0: fast interrupt
uart0: console (115200,n,8,1)
siba_cc_attach: done
bfe0: <Broadcom 44xx Ethernet Chip> at mem 0x18001000-0x18001fff irq 1 on siba0
bfe0: PHY Reset would not complete.
mii_rreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg:
timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutbfe_robo_config_vlan: Add port 1 untagged  to VLAN=1 mii_wreg:
timeoutbfe_robo_config_vlan: Add port 2 untagged  to VLAN=1 mii_wreg: timeoutbfe_robo_config_vlan: Add port 3 untagged  to VLAN=1
mii_wreg: timeoutbfe_robo_config_vlan: Add port 4 untagged  to VLAN=1
mii_wreg: timeoutbfe_robo_config_vlan: Add port 5 untagged CPU MII to VLAN=1
mii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_rreg: timeoutmii_wreg: timeoutmii_wreg:
timeoutbfe_robo_config_vlan: Add port 0 untagged  to VLAN=2 mii_wreg: timeoutbfe_robo_config_vlan: Add port 5 tagged CPU MII to
VLAN=2 mii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_rreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg:
timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg:
timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg:
timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg:
timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_rreg: timeoutmii_wreg:
timeoutmii_rreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmiibus0: <MII bus>
on bfe0 bfeswitch0: <BCM5325 10/100baseTX Switch PHY> PHY 0 on miibus0 bfeswitch0:  100baseTX-FDX bfe0: Ethernet address:
00:1b:11:31:df:0a bfe0: [MPSAFE] bfe0: [ITHREAD] bfe1: <Broadcom 44xx Ethernet Chip> at mem 0x18002000-0x18002fff irq 1 on siba0
bfe1: BUG!  Timeout waiting for bit 00000002 of register f98 to set. bfe1: PHY Reset would not complete.
mii_rreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg:
timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutbfe_robo_config_vlan: Add port 1 untagged  to VLAN=1 mii_wreg:
timeoutbfe_robo_config_vlan: Add port 2 untagged  to VLAN=1 mii_wreg: timeoutbfe_robo_config_vlan: Add port 3 untagged  to VLAN=1
mii_wreg: timeoutbfe_robo_config_vlan: Add port 4 untagged  to VLAN=1
mii_wreg: timeoutbfe_robo_config_vlan: Add port 5 untagged CPU MII to VLAN=1
mii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_rreg: timeoutmii_wreg: timeoutmii_wreg:
timeoutbfe_robo_config_vlan: Add port 0 untagged  to VLAN=2 mii_wreg: timeoutbfe_robo_config_vlan: Add port 5 tagged CPU MII to
VLAN=2 mii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_rreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg:
timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg:
timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg:
timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg:
timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_rreg: timeoutmii_wreg:
timeoutmii_rreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmii_wreg: timeoutmiibus1: <MII bus>
on bfe1 bfeswitch1: <BCM5325 10/100baseTX Switch PHY> PHY 0 on miibus1 bfeswitch1:  100baseTX-FDX bfe1: Ethernet address:
00:1b:11:31:df:0a bfe1: [MPSAFE] bfe1: [ITHREAD] ohci0: <SiBa integrated OHCI controller> at mem 0x18003000-0x18003fff irq 3 on
siba0 ohci0: [MPSAFE] ohci0: [ITHREAD]
usbus0 on ohci0
siba0: <PCI host interface> at device 4 (no driver attached)
siba_mips0: <MIPS 3302 processor> at mem 0x18005000-0x18005fff on siba0
siba_mips0: SBIPSFlag=03020100
siba_mips0: SBIPSFlagHigh=00000000
siba_mips0: SBIntVec=000000f0
siba0: <V90 Codec Core> at device 6 (no driver attached)
siba0: <IPSEC accelerator> at device 7 (no driver attached)
siba_sdram0: <SDRAM/DDR core> at mem 0x18008000-0x18008fff on siba0
Device configuration finished.
Timecounter "MIPS32" frequency 132000000 Hz quality 800
Timecounters tick every 10.000 msec
usbus0: 12Mbps Full Speed USB v1.0
bootpc_init: wired to interface 'bfe0'
bfe0: PHY Reset would not complete.
Sending DHCP Discover packet from interface bfe0 (00:1b:11:31:df:0a)
ugen0.1: <Broadcom OHCI v> at usbus0
uhub0: <Broadcom OHCI v OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
Received DHCP Offer packet on bfe0 from 0.0.0.0 (accepted) (no root path)
uhub0: 2 ports with 2 removable, self powered
uhub_reattach_port:365: giving up port reset - device vanished!
Sending DHCP Request packet from interface bfe0 (00:1b:11:31:df:0a)
Received DHCP Ack packet on bfe0 from 0.0.0.0 (accepted) (got root path)
uhub_reattach_port:365: giving up port reset - device vanished!
uhub_reattach_port:365: giving up port reset - device vanished!
bfe0 at 192.168.0.1 server 0.0.0.0
subnet mask 255.255.255.0 rootfs 192.168.0.90:/usr/home/ray/Projects/MIPS/FreeBSD/rootfs-mips 
Adjusted interface bfe0
Trying to mount root from nfs:
NFS ROOT: 192.168.0.90:/usr/home/ray/Projects/MIPS/FreeBSD/rootfs-mips
warning: no time-of-day clock registered, system time will not be set accurately
warning: no time-of-day clock registered, system time will not be set accurately
start_init: trying /sbin/init
Interface bfe0 IP-Address 192.168.0.1 Broadcast 192.168.0.255 
uhub_reattach_port:365: giving up port reset - device vanished!
No suitable dump device was found.
uhub_reattach_port:365: giving up port reset - device vanished!
Entropy harvesting:.
mount_nfs: can't update /var/db/mounttab for 192.168.0.90:/usr/home/ray/Projects/MIPS/FreeBSD/rootfs-mips
uhub_reattach_port:365: giving up port reset - device vanished!
uhub_reattach_port:365: giving up port reset - device vanished!
uhub_reattach_port:365: giving up port reset - device vanished!
uhub_reattach_port:365: giving up port reset - device vanished!
uhub_reattach_port:365: giving up port reset - device vanished!
uhub_reattach_port:365: giving up port reset - device vanished!
uhub_reattach_port:365: giving up port reset - device vanished!
uhub_reattach_port:365: giving up port reset - device vanished!
mount_mfs: mount exited with error code 1
mount_mfs: mount exited with error code 1
mount: proc : Operation not supported by device
Mounting /etc/fstab filesystems failed,  startup aborted
ERROR: ABORTING BOOT (sending SIGTERM to parent)!
Jan  1 00:00:26 init: /bin/sh on /etc/rc terminated abnormally, going to single user mode
Enter full pathname of shell or RETURN for /bin/sh

-- 
Alexandr Rybalko <ray at dlink.ua>


More information about the freebsd-mips mailing list