make install fails on FreeBSD 6.2 release

[Hans Petter Selasky]

Hi,

All you probably have to do is to add the USB ID to the I4B USB driver.

Could you install /usr/ports/sysutils/udesc_dump

Then run that program and send me the output. 

--HPS

On Friday 24 August 2007, andreas wrote:
> Hi Hans,
>
> wonderful, that helped.
> I already had the Kernel sources, but was missing the userland.
>
> Now, there's the next problem:
> I want to make use of my Draytek USM miniVigor, which is on the list
> of supported devices.
>
> I built an ISDN-enabled Kernel (with both device sound and device
> usb), installed it, rebooted and fiddled around with isdnd.rc (see
> below)
>
> dmesg shows appropriate entries for ISDN and shows the miniVigor.
>
> ###
> capi: CAPI call control device attached, v2.07
> i4b: ISDN call control device attached
> ...
> i4btrc: 64 ISDN trace device(s) attached
> i4brbch: 8 raw B channel access device(s) attached
> i4btel: 8 ISDN telephony interface device(s) attached
> i4bipr: 8 IP over raw HDLC ISDN device(s) attached (VJ header
> compression)
> i4bisppp: 8 ISDN SyncPPP device(s) attached
> i4bctl: ISDN system control port attached
> ...
> ugen0: <vendor 0x0675 USB ISDN TA, class 255/0, rev 1.10/1.00, addr 126>
> ###
>
> however, isdnmonitor does not even show ISDN channels with a TEI
>
> isdnmonitor-output:
> ##
> remote protocol version is 00.05
> our rights = 0x72
> 64 controller(s) found:
>          controller 0:
>          controller 1:
> ...
>          controller 62:
>          controller 63:
> 1 entries found:
>          entry 0: device DRVR_TEL0
> 24.08.2007 15:27:18: controller 0, TEI is -1
> 24.08.2007 15:27:18: layer 1 change on controller 0: down
> 24.08.2007 15:27:18: layer 2 change on controller 0: down
> ...
> (same for all controllers up to 63)
>
>
> ##
>
> Just to get started, I'm trying to get an answering machine running,
> with the configuration from http://people.freebsd.org/~hm/i4b-095/
> node81.html
>
> Do I get it right, that I need to setup controllers and somehow make
> the USB-TA known to the isdnd, because it will appear as "controller
> 7" or something?
> (as listed in http://www.turbocat.net/~hselasky/isdn4bsd/
> index_ObjG_00.html )
>
>
> Do I need to install chan_capi (and Asterisk) before the answering
> machine will work with the USB-TA?
>
> thanks for your help and patience,
> Andreas
>
> On 24.08.2007, at 08:36, Hans Petter Selasky wrote:
> > Hi Andreas,
> >
> > You need to install the kernel sources and some userland sources, at
> > least /usr/src/usr.sbin .
> >
> > --HPS
> >
> > On Thursday 23 August 2007, andreas wrote:
> >> Hi Everyone,
> >>
> >> trying to install i4b (from svn) to a FreeBSD 6.2 release gives me
> >> the error following below.
> >>
> >> Now that I've tried it on two sepearate virgin installations, I'd
> >> like to ask for a little help.
> >>
> >> Where is the line making the wrong call to install and how do I fix
> >> it? e.g., is it make or a port, or... ?