Installing on zx6000

[Anton Shterenlikht]

On Fri, Jun 29, 2012 at 12:13:42AM +0200, ?meric Maschino wrote:
> Hello,
> 
> Resetting EFI didn't help here neither. I don't know if it will help
> diagnose the problem, but please find attached the boot log that I've
> recorded on a serial console. Passed the last line, I was getting a
> hard reset.
> 
> If it can help further, I've also attached the system information of
> my zx6000. It seems that Hiroki Sato's zx6000 is sported with the same
> B1 stepping 1.5GHz Itanium² CPUs than mine. But something else is
> probably preventing my system to successfully boot FreeBSD.
> 
> Hiroki (is this your firstname? Or should I have call you Sato? ),
> could you have a look at my system information and compare with yours
> in order to identify the differences?

So you do indeed boot!

Below is dmesg.boot from my rx2600,
which is very similar to zx6000,
but intented for rack mount use.
It looks very similar to yours,
except I've less RAM.

Your log ends with

da0 at mpt0 bus 0 scbus1 target 0 lun 0

Perhaps something is wrong with the disk,
or the controller?

Have you got MP console installed?
Can you check the system log (SL command
in MP console, there should be a BMC
equivalent)? Are there any logged events
prior to the hard reset.

Anton

****************************************************

GDB: debug ports: uart
GDB: current port: uart
KDB: debugger backends: ddb gdb
KDB: current backend: ddb
Copyright (c) 1992-2012 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 10.0-CURRENT #6 r237134: Mon Jun 18 09:02:17 BST 2012
    root at mech-cluster241.men.bris.ac.uk:/usr/obj/usr/src/sys/TZAV ia64
WARNING: WITNESS option enabled, expect reduced performance.
CPU: Madison (1500 MHz Itanium 2)
  Origin = "GenuineIntel"  Revision = 5
  Features = 0x1<LB>
real memory  = 8533164032 (8137 MB)
avail memory = 8354324480 (7967 MB)
FPSWA Revision = 0x10012, Entry = 0xe0000040ffe62050
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0: ACPI Id=0, SAPIC Id=0, SAPIC Eid=0 (BSP)
cpu1: ACPI Id=1, SAPIC Id=1, SAPIC Eid=0
Event timer "ITC" frequency 1500000000 Hz quality 1000
ACPI Warning: 32/64X length mismatch in Gpe0Block: 32/16 (20120518/tbfadt-598)
ACPI Warning: 32/64X length mismatch in Gpe1Block: 32/16 (20120518/tbfadt-598)
acpi0: <HP> on motherboard
acpi0: Power Button (fixed)
acpi0: Sleep Button (fixed)
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
acpi_timer0: <32-bit timer at 3.579545MHz> iomem 0xff5c1004-0xff5c1007 on acpi0
acpi_tz0: <Thermal Zone> on acpi0
pcib0: <ACPI Host-PCI bridge> on acpi0
pcib0: could not evaluate _ADR - AE_NOT_FOUND
pci0: <ACPI PCI bus> on pcib0
ohci0: <NEC uPD 9210 USB controller> mem 0x80023000-0x80023fff irq 16 at device 1.0 on pci0
usbus0 on ohci0
ohci1: <NEC uPD 9210 USB controller> mem 0x80022000-0x80022fff irq 17 at device 1.1 on pci0
usbus1 on ohci1
ehci0: <NEC uPD 720100 USB 2.0 controller> mem 0x80021000-0x800210ff irq 18 at device 1.2 on pci0
usbus2: EHCI version 0.95
usbus2 on ehci0
pci0: <mass storage, ATA> at device 2.0 (no driver attached)
fxp0: <Intel 82550C Pro/100 Ethernet> port 0xd00-0xd3f mem 0x80020000-0x80020fff,0x80000000-0x8001ffff irq 20 at device 3.0 on pci0
miibus0: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> PHY 1 on miibus0
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto, auto-flow
fxp0: Ethernet address: 00:11:0a:31:d6:ec
pcib1: <ACPI Host-PCI bridge> on acpi0
pcib1: could not evaluate _ADR - AE_NOT_FOUND
pci32: <ACPI PCI bus> on pcib1
mpt0: <LSILogic 1030 Ultra4 Adapter> port 0x2100-0x21ff mem 0x90840000-0x9084ffff,0x90830000-0x9083ffff irq 27 at device 1.0 on pci32
mpt0: MPI Version=1.2.12.0
mpt1: <LSILogic 1030 Ultra4 Adapter> port 0x2000-0x20ff mem 0x90820000-0x9082ffff,0x90810000-0x9081ffff irq 28 at device 1.1 on pci32
mpt1: MPI Version=1.2.12.0
bge0: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. 0x000105> mem 0x90800000-0x9080ffff irq 29 at device 2.0 on pci32
bge0: CHIP ID 0x00000105; ASIC REV 0x00; CHIP REV 0x01; PCI on PCI-X 66 MHz; 64bit
miibus1: <MII bus> on bge0
brgphy0: <BCM5701 1000BASE-T media interface> PHY 1 on miibus1
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
bge0: Ethernet address: 00:11:0a:31:36:40
pcib2: <ACPI Host-PCI bridge> on acpi0
pcib2: could not evaluate _ADR - AE_NOT_FOUND
pci64: <ACPI PCI bus> on pcib2
pcib3: <ACPI Host-PCI bridge> on acpi0
pcib3: could not evaluate _ADR - AE_NOT_FOUND
pci96: <ACPI PCI bus> on pcib3
pcib4: <ACPI Host-PCI bridge> on acpi0
pcib4: could not evaluate _ADR - AE_NOT_FOUND
pci128: <ACPI PCI bus> on pcib4
pcib5: <ACPI Host-PCI bridge> on acpi0
pcib5: could not evaluate _ADR - AE_NOT_FOUND
pci192: <ACPI PCI bus> on pcib5
pcib6: <ACPI Host-PCI bridge> on acpi0
pcib6: could not evaluate _ADR - AE_NOT_FOUND
pci224: <ACPI PCI bus> on pcib6
uart0: <16550 or compatible> mem 0xf4051000-0xf405100f irq 82 at device 1.0 on pci224
puc0: <HP Diva Serial [GSP] Multiport UART - Everest SP2> mem 0xf4050000-0xf4050fff,0xf4020000-0xf403ffff irq 82 at device 1.1 on pci224
uart1: <Non-standard ns8250 class UART with FIFOs> at port 1 on puc0
uart1: console (9600,n,8,1)
uart2: <Non-standard ns8250 class UART with FIFOs> at port 3 on puc0
vgapci0: <VGA-compatible display> port 0xe000-0xe0ff mem 0xf0000000-0xf3ffffff,0xf4040000-0xf404ffff at device 2.0 on pci224
uart3: <16550 or compatible> iomem 0xff5e0000-0xff5e0007 irq 34 on acpi0
uart4: <16550 or compatible> iomem 0xff5e2000-0xff5e2007 irq 35 on acpi0
uart4: debug port (9600,n,8,1)
Timecounters tick every 1.000 msec
IP Filter: v4.1.28 initialized.  Default = block all, Logging = enabled
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 480Mbps High Speed USB v2.0
ugen0.1: <NEC> at usbus0
uhub0: <NEC OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <NEC> at usbus1
uhub1: <NEC OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <NEC> at usbus2
uhub2: <NEC EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
uhub1: 2 ports with 2 removable, self powered
uhub0: 3 ports with 3 removable, self powered
uhub2: 5 ports with 5 removable, self powered
WARNING: WITNESS option enabled, expect reduced performance.
da0 at mpt0 bus 0 scbus0 target 0 lun 0
da0: <HP 73.4G ST373454LC HPC3> Fixed Direct Access SCSI-3 device 
da0: 320.000MB/s transfers (160.000MHz, offset 63, 16bit)
da0: Command Queueing enabled
da0: 70007MB (143374738 512 byte sectors: 255H 63S/T 8924C)
da1 at mpt0 bus 0 scbus0 target 1 lun 0
da1: <HP 73.4G ST373454LC HPC2> Fixed Direct Access SCSI-3 device 
da1: 320.000MB/s transfers (160.000MHz, offset 63, 16bit)
da1: Command Queueing enabled
da1: 70007MB (143374738 512 byte sectors: 255H 63S/T 8924C)
da2 at mpt1 bus 0 scbus1 target 2 lun 0
da2: <COMPAQ BD03685A24 HPB7> Fixed Direct Access SCSI-3 device 
da2: 320.000MB/s transfers (160.000MHz, offset 63, 16bit)
da2: Command Queueing enabled
da2: 34732MB (71132000 512 byte sectors: 255H 63S/T 4427C)
Trying to mount root from ufs:/dev/da0p2 [rw]...


-- 
Anton Shterenlikht
Room 2.6, Queen's Building
Mech Eng Dept
Bristol University
University Walk, Bristol BS8 1TR, UK
Tel: +44 (0)117 331 5944
Fax: +44 (0)117 929 4423