Installation Problem - 8.0
Mister Itanium
itanium.user at gmail.com
Sat Mar 13 21:48:52 UTC 2010
Sorry, but those log files are old (when the HDD was set as a SECONDARY *
SLAVE*, so the disk wasn't being detected)
Now the disk is the PRIMARY *MASTER* and is being detected at boot.
This is the current boot verbose log: (http://paste.pocoo.org/show/189298/)
\Entering /boot/kernel/kernel at 0xe000000004080000...
PAL Proc at 0xe00000007ff08010
SAL Proc at 0xe00000007ff48020, GP at 0xe0000000801712c0
SAL: AP wake-up vector: 0xf0
Platform clock frequency 199476428 Hz
Processor ratio 14/2, Bus ratio 1/1, ITC ratio 14/2
ptc.e base=0x0, count1=1, count2=1, stride1=0x0, stride2=0x0
Processor supports 24 Region ID bits
Trying VHPT size 0x1000000
Putting VHPT at 0x6000000
Splitting [0x560c000-0x7fb40000]
Copyright (c) 1992-2009 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.0-RELEASE #0: Sun Nov 22 01:11:28 UTC 2009
root at pluto1.freebsd.org:/usr/obj/usr/src/sys/GENERIC
UNWIND: table added: base=e000000004000000, start=e000000004bbb060,
end=e000000004bfc250
Preloaded elf kernel "/boot/kernel/kernel" at 0xe000000005608580.
Preloaded mfs_root "/boot/mfsroot" at 0xe000000005608660.
CPU: Madison (1396.33-Mhz Itanium 2)
Origin = "GenuineIntel" Revision = 5
Features = 0x1<LB>
real memory = 4282097664 (4083 MB)
Physical memory chunk(s):
0x01900000 - 0x03ffffff, 40894464 bytes (4992 pages)
0x0560c000 - 0x05ffffff, 10436608 bytes (1274 pages)
0x0a000000 - 0x7fb3ffff, 1974730752 bytes (241056 pages)
0x7ff7c000 - 0x7ff81fff, 24576 bytes (3 pages)
0x180000000 - 0x1fb455fff, 2068144128 bytes (252459 pages)
0x1feffe000 - 0x1ff453fff, 4546560 bytes (555 pages)
0x1ff802000 - 0x1ff8fdfff, 1032192 bytes (126 pages)
0x1ff900000 - 0x1ff905fff, 24576 bytes (3 pages)
0x1ff9fe000 - 0x1ffd63fff, 3563520 bytes (435 pages)
0x1ffdfe000 - 0x1ffe0ffff, 73728 bytes (9 pages)
0x1ffe7e000 - 0x1fffb7fff, 1286144 bytes (157 pages)
avail memory = 4084006912 (3894 MB)
FPSWA Revision = 0x10012, Entry = 0xe0000001ffe60050
Table 'FACP' at 0xe00000007ff99138
Table 'APIC' at 0xe00000007ff99230
Local APIC address=0xfee00000
Local SAPIC entry
ProcessorId=0x0, Id=0xc0, Eid=0x18
Local SAPIC entry
ProcessorId=0x1, Id=0xc6, Eid=0x18
I/O SAPIC entry
Id=0x0, InterruptBase=0x0, Address=0xfec00000
I/O SAPIC entry
Id=0x2, InterruptBase=0x18, Address=0xfaffe000
I/O SAPIC entry
Id=0x1, InterruptBase=0x30, Address=0xfafff000
Interrupt source override entry
Bus=0, Source=9, Irq=0x9
Platform interrupt entry
Polarity=3, TriggerMode=3, Id=0xc6, Eid=0x18, Vector=0x1e, Irq=22
Table 'IPPT' at 0xe00000007ff99308
Table 'SPCR' at 0xe00000007ff99340
MCA: allocated 16384 bytes for state info.
SMP: waking up cpu1
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0: ACPI Id=1, SAPIC Id=c6, SAPIC Eid=18 (BSP)
cpu1: ACPI Id=0, SAPIC Id=c0, SAPIC Eid=18
ULE: setup cpu 0
ULE: setup cpu 1
mem: <memory>
null: <null device, zero device>
nfslock: pseudo-device
random: <entropy source, Software, Yarrow>
ACPI: RSDP 0x7ff99000 00024 (v2 AMI )
ACPI: XSDT 0x7ff99090 00044 (v1 AMI TIGER_2W 01072002 MSFT 00010013)
ACPI: FACP 0x7ff99138 000F4 (v3 AMI TIGER_2W 01072002 MSFT 00010013)
ACPI: DSDT 0x7ff9b000 0220E (v1 AMI TIGER2W 00000000 MSFT 0100000D)
ACPI: FACS 0x7ff992c0 00040
ACPI: APIC 0x7ff99230 0008E (v1 AMI TIGER_2W 01072002 MSFT 00010013)
ACPI: IPPT 0x7ff99308 00034 (v1 AMI TIGER_2W 01072002 MSFT 00010013)
ACPI: SPCR 0x7ff99340 00050 (v1 AMI TIGER_2W 01072002 MSFT 00010013)
nexus0: registered as a time-of-day clock (resolution 1000us)
acpi0: <AMI TIGER_2W> on motherboard
acpi0: [MPSAFE]
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
AcpiOsDerivePciId: \_SB_.CSFF.IOH5.IOHC -> bus 255 dev 28 func 5
AcpiOsDerivePciId: \_SB_.CSFF.IOH1.IO01 -> bus 255 dev 28 func 1
AcpiOsDerivePciId: \_SB_.CSFF.IOH2.IO02 -> bus 255 dev 28 func 2
ACPI timer: 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 -> 10
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0xc08-0xc0b on acpi0
pcib0: <ACPI Host-PCI bridge> on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: domain=0, physical bus=0
found-> vendor=0x8086, dev=0x244e, revid=0x82
domain=0, bus=0, slot=30, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0147, statreg=0x0080, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x0b (2750 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x24c0, revid=0x02
domain=0, bus=0, slot=31, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x010f, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x24cb, revid=0x02
domain=0, bus=0, slot=31, func=1
class=01-01-8a, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=0
map[20]: type I/O Port, range 32, base 0x1000, size 4, enabled
map[24]: type Memory, range 32, base 0, size 10, memory disabled
pcib0: no PRT entry for 0.31.INTA
found-> vendor=0x8086, dev=0x24c3, revid=0x02
domain=0, bus=0, slot=31, func=3
class=0c-05-00, hdrtype=0x00, mfdev=0
cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=0
map[20]: type I/O Port, range 32, base 0xcc0, size 5, enabled
pcib0: no PRT entry for 0.31.INTB
pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pcib1: domain 0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xd000-0xdfff
pcib1: memory decode 0xfb000000-0xfd0fffff
pcib1: no prefetched decode
pcib1: Subtractively decoded bridge.
pci1: <ACPI PCI bus> on pcib1
pci1: domain=0, physical bus=1
found-> vendor=0x1002, dev=0x4752, revid=0x27
domain=0, bus=1, slot=2, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0087, statreg=0x0290, cachelnsz=32 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type Memory, range 32, base 0xfc000000, size 24, enabled
pcib1: requested memory range 0xfc000000-0xfcffffff: good
map[14]: type I/O Port, range 32, base 0xd800, size 8, enabled
pcib1: requested I/O range 0xd800-0xd8ff: in range
map[18]: type Memory, range 32, base 0xfd0ff000, size 12, enabled
pcib1: requested memory range 0xfd0ff000-0xfd0fffff: good
pcib1: matched entry for 1.2.INTA
pcib1: slot 2 INTA hardwired to IRQ 18
vgapci0: <VGA-compatible display> port 0xd800-0xd8ff mem
0xfc000000-0xfcffffff,0xfd0ff000-0xfd0fffff irq 18 at device 2.0 on
pci1
pci0: <bridge, PCI-ISA> at device 31.0 (no driver attached)
atapci0: <Intel ICH4 UDMA100 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1000-0x100f irq 0 at device 31.1
on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0x1000
ata0: <ATA channel 0> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0: stat0=0x90 err=0x90 lsb=0x90 msb=0x90
ata0: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=50 stat1=00 devices=0x1
ata0: [MPSAFE]
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=03 ostat0=50 ostat1=01
ata1: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: stat1=0x01 err=0x04 lsb=0x00 msb=0x00
ata1: reset tp2 stat0=00 stat1=01 devices=0x10000
ata1: [MPSAFE]
ata1: [ITHREAD]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
pcib2: <ACPI Host-PCI bridge> on acpi0
pcib2: could not get PCI interrupt routing table for \_SB_.PCI1 - AE_NOT_FOUND
pci2: <ACPI PCI bus> on pcib2
pci2: domain=0, physical bus=2
found-> vendor=0x8086, dev=0x1461, revid=0x04
domain=0, bus=2, slot=28, func=0
class=08-00-20, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0030, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type Memory, range 32, base 0xfafff000, size 12, enabled
found-> vendor=0x8086, dev=0x1460, revid=0x04
domain=0, bus=2, slot=29, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0147, statreg=0x0030, cachelnsz=32 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x1461, revid=0x04
domain=0, bus=2, slot=30, func=0
class=08-00-20, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0030, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type Memory, range 32, base 0xfaffe000, size 12, enabled
found-> vendor=0x8086, dev=0x1460, revid=0x04
domain=0, bus=2, slot=31, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0147, statreg=0x0030, cachelnsz=32 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns)
pci2: <base peripheral, interrupt controller> at device 28.0 (no
driver attached)
pcib3: <ACPI PCI-PCI bridge> at device 29.0 on pci2
pcib3: domain 0
pcib3: secondary bus 3
pcib3: subordinate bus 3
pcib3: I/O decode 0xf000-0xffff
pcib3: memory decode 0xfa000000-0xfa0fffff
pcib3: no prefetched decode
pci3: <ACPI PCI bus> on pcib3
pci3: domain=0, physical bus=3
found-> vendor=0x8086, dev=0x1010, revid=0x01
domain=0, bus=3, slot=2, func=0
class=02-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0117, statreg=0x0230, cachelnsz=32 (dwords)
lattimer=0x40 (1920 ns), mingnt=0xff (63750 ns), maxlat=0x00 (0 ns)
intpin=a, irq=3
powerspec 2 supports D0 D3 current D0
MSI supports 1 message, 64 bit
map[10]: type Memory, range 64, base 0xfa0c0000, size 17, enabled
pcib3: requested memory range 0xfa0c0000-0xfa0dffff: good
map[20]: type I/O Port, range 32, base 0xfe80, size 6, enabled
pcib3: requested I/O range 0xfe80-0xfebf: in range
pcib3: matched entry for 3.2.INTA
pcib3: slot 2 INTA hardwired to IRQ 48
found-> vendor=0x8086, dev=0x1010, revid=0x01
domain=0, bus=3, slot=2, func=1
class=02-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0117, statreg=0x0230, cachelnsz=32 (dwords)
lattimer=0x40 (1920 ns), mingnt=0xff (63750 ns), maxlat=0x00 (0 ns)
intpin=b, irq=3
powerspec 2 supports D0 D3 current D0
MSI supports 1 message, 64 bit
map[10]: type Memory, range 64, base 0xfa0e0000, size 17, enabled
pcib3: requested memory range 0xfa0e0000-0xfa0fffff: good
map[20]: type I/O Port, range 32, base 0xff00, size 6, enabled
pcib3: requested I/O range 0xff00-0xff3f: in range
pcib3: matched entry for 3.2.INTB
pcib3: slot 2 INTB hardwired to IRQ 49
em0: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0xfe80-0xfebf
mem 0xfa0c0000-0xfa0dffff irq 48 at device 2.0 on pci3
em0: Reserved 0x20000 bytes for rid 0x10 type 3 at 0xfa0c0000
em0: Reserved 0x40 bytes for rid 0x20 type 4 at 0xfe80
em0: [FILTER]
em0: bpf attached
em0: Ethernet address: 00:30:48:20:f6:2a
em1: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0xff00-0xff3f
mem 0xfa0e0000-0xfa0fffff irq 49 at device 2.1 on pci3
em1: Reserved 0x20000 bytes for rid 0x10 type 3 at 0xfa0e0000
em1: Reserved 0x40 bytes for rid 0x20 type 4 at 0xff00
em1: [FILTER]
em1: bpf attached
em1: Ethernet address: 00:30:48:20:f6:2b
pci2: <base peripheral, interrupt controller> at device 30.0 (no
driver attached)
pcib4: <ACPI PCI-PCI bridge> at device 31.0 on pci2
pcib4: domain 0
pcib4: secondary bus 4
pcib4: subordinate bus 4
pcib4: I/O decode 0xf000-0xfff
pcib4: no prefetched decode
pci4: <ACPI PCI bus> on pcib4
pci4: domain=0, physical bus=4
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 on acpi0
uart0: [FILTER]
uart0: fast interrupt
uart0: console (115200,n,8,1)
cpu0: <ACPI CPU> on acpi0
cpu0: switching to generic Cx mode
cpu1: <ACPI CPU> on acpi0
Reducing kern.maxvnodes 131431 -> 100000
procfs registered
Timecounters tick every 1.000 msec
lo0: bpf attached
ata0: Identifying devices: 00000001
ata0: New devices: 00000001
md0: Preloaded image </boot/mfsroot> 8388608 bytes at 0xe000000004e08580
ata0-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=80 wire
*ad0: setting PIO4 on ICH4 chip
ad0: setting UDMA100 on ICH4 chip
ad0: 114473MB <Seagate ST3120026A 8.01> at ata0-master UDMA100
ad0: 234441648 sectors [232581C/16H/63S] 16 sectors/interrupt 1 depth queue*
GEOM: new disk ad0
ad0: Intel check1 failed
ad0: Adaptec check1 failed
ad0: LSI (v3) check1 failed
ad0: LSI (v2) check1 failed
ad0: FreeBSD check1 failed
ata1: Identifying devices: 00010000
ata1: New devices: 00010000
ata1-master: pio=PIO4 wdma=WDMA2 udma=UDMA33 cable=40 wire
acd0: setting PIO4 on ICH4 chip
acd0: setting UDMA33 on ICH4 chip
acd0: <CD-224E/1.9A> CDROM drive at ata1 as master
acd0: read 4134KB/s (4134KB/s), 128KB buffer, UDMA33
acd0: Reads: CDR, CDRW, CDDA stream, packet
acd0: Writes:
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: CD-ROM 120mm data disc
ATA PseudoRAID loaded
acd0: FAILURE - READ_BIG MEDIUM ERROR asc=0x11 ascq=0x00
acd0: FAILURE - READ_BIG MEDIUM ERROR asc=0x11 ascq=0x00
Trying to mount root from ufs:/dev/md0
ct_to_ts([2010-03-13 21:41:12]) = 1268516472.000000000
start_init: trying /sbin/init
start_init: trying /sbin/oinit
start_init: trying /sbin/init.bak
start_init: trying /rescue/init
start_init: trying /stand/sysinstall
/stand/sysinstall running as init on serial console
These are the predefined terminal types available to
sysinstall when running stand-alone. Please choose the
closest match for your particular terminal.
1 ...................... Standard ANSI terminal.
2 ...................... VT100 or compatible terminal.
3 ...................... FreeBSD system console (color).
4 ...................... FreeBSD system console (monochrome).
5 ...................... xterm terminal emulator.
Your choice: (1-5)
On Sat, Mar 13, 2010 at 4:03 PM, Marcel Moolenaar <xcllnt at mac.com> wrote:
>
> On Mar 13, 2010, at 12:54 PM, Mister Itanium wrote:
>
> *snip*
>
> > This is what I get when I try to WRITE something on the disk:
> >
> > ===============================================
> > ad0: TIMEOUT - WRITE_DMA retrying (0 retries left) LBA=0
> > GEOM: ad0: corrupt or invalid GPT detected.
> > GEOM: ad0: GPT rejected -- may not be recoverable.
> > ===============================================
> >
> > And then I get a message saying it can't wirte on ad0 disk etc..
>
> > Question number 1:
> > Any suggestions/help on resolving this?
>
>
> You probably have a dead disk. Replace the disk and see what
> happens. Notice how the disk wasn't probed at first as well:
>
> *snip*
> > atapci0: <Intel ICH4 UDMA100 controller> port
> 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1000-0x100f irq 0 at device 31.1 on
> pci0
> > atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0x1000
> > ata0: <ATA channel 0> on atapci0
> > atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
> > atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
> > ata0: reset tp1 mask=03 ostat0=00 ostat1=50
> > ata0: stat0=0x01 err=0x01 lsb=0x01 msb=0x01
> > ata0: stat1=0x01 err=0x01 lsb=0x01 msb=0x01
> > ata0: reset tp2 stat0=01 stat1=01 devices=0x0
> > ata0: [MPSAFE]
> > ata0: [ITHREAD]
> > ata1: <ATA channel 1> on atapci0
> > atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
> > atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
> > ata1: reset tp1 mask=03 ostat0=50 ostat1=01
> > ata1: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
> > ata1: stat1=0x01 err=0x04 lsb=0x00 msb=0x00
> > ata1: reset tp2 stat0=00 stat1=01 devices=0x10000
> > ata1: [MPSAFE]
> > ata1: [ITHREAD]
> *snip*
> > ata0: Identifying devices: 00000000
> > ata0: New devices: 00000000
> > ata1: Identifying devices: 00010000
> > ata1: New devices: 00010000
> *snip*
> > ata1-master: pio=PIO4 wdma=WDMA2 udma=UDMA33 cable=40 wire
> > acd0: setting PIO4 on ICH4 chip
> > acd0: setting UDMA33 on ICH4 chip
> > acd0: <CD-224E/1.9A> CDROM drive at ata1 as master
> > acd0: read 4134KB/s (4134KB/s), 128KB buffer, UDMA33
> > acd0: Reads: CDR, CDRW, CDDA stream, packet
> > acd0: Writes:
> > acd0: Audio: play, 256 volume levels
> > acd0: Mechanism: ejectable tray, unlocked
> > acd0: Medium: CD-ROM 120mm data disc
> *snip*
> > ATA PseudoRAID loaded
> *snip*
> > acd0: FAILURE - READ_BIG MEDIUM ERROR asc=0x11 ascq=0x00
> > acd0: FAILURE - READ_BIG MEDIUM ERROR asc=0x11 ascq=0x00
> *snip*
>
> There's no ad0 at all. You may want to check the RAID setting on
> the controller. If it's enabled, disable it...
>
> > Question n.2:
> > How do I disable ACPI on boot on IA64 machines?
>
> You can't. ACPI is mandatory. Nothing works without it. ACPI is at the
> root of everything.
>
> > PS: HDD works fine under Debian Linux, using fdisk I'm able to
> change/delete/add partitions without a problem, which makes me think it's
> not a hardware issue.
>
> Did you move the hard disk onto another machine to do this?
>
> HTH,
>
> --
> Marcel Moolenaar
> xcllnt at mac.com
>
>
>
>
More information about the freebsd-ia64
mailing list