Intel DP45SG motherboard problem (amd64)
Alastair Hogge
agh at coolrhaug.com
Sun Mar 28 00:26:23 UTC 2010
On Wed March 17 2010 23:23:03 John Baldwin wrote:
> On Tuesday 16 March 2010 9:22:28 am Alastair Hogge wrote:
> > On Tue March 2 2010 00:54:00 John Baldwin wrote:
> > > This would not change acpidump output, just the kernel. Are you able
> > > to capture the boot messages with this kernel?
> >
> > Full log:
> > http://codepad.org/96PT5OO8
>
> Oh! ACPI is working, but the MADT is not so it's trying to mix and match
> mptable (for SMP) with ACPI. Odd that you didn't get a warning message
> about the checksum failing from boot -v. Try this patch:
>
> Index: amd64/acpica/acpi_machdep.c
> ===================================================================
> --- amd64/acpica/acpi_machdep.c (revision 205249)
> +++ amd64/acpica/acpi_machdep.c (working copy)
> @@ -627,8 +627,10 @@
> if (ACPI_FAILURE(AcpiTbChecksum(table, length))) {
> if (bootverbose)
> printf("ACPI: Failed checksum for table %s\n", sig);
> +#if (ACPI_CHECKSUM_ABORT)
> table_unmap(table, length);
> return (NULL);
> +#endif
> }
> return (table);
> }
> Index: i386/acpica/acpi_machdep.c
> ===================================================================
> --- i386/acpica/acpi_machdep.c (revision 205249)
> +++ i386/acpica/acpi_machdep.c (working copy)
> @@ -641,8 +641,10 @@
> if (ACPI_FAILURE(AcpiTbChecksum(table, length))) {
> if (bootverbose)
> printf("ACPI: Failed checksum for table %s\n", sig);
> +#if (ACPI_CHECKSUM_ABORT)
> table_unmap(table, length);
> return (NULL);
> +#endif
> }
> return (table);
> }
>
OK, I've applied the patch to my i386 system & there doesn't appear to be
problems so far.
I also created an amd64 bootonly CD with the patch & was able to boot into
sysinstall :-)
[dcons connected]
lapic: Divisor 2, Frequency 166664803 Hz
ioapic0: routing intpin 8 (ISA IRQ 8) to lapic 0 vector 59
Timecounter "TSC" frequency 2833301532 Hz quality -100
Timecounters tick every 1.000 msec
vlan: initialized, using hash tables with chaining
lo0: bpf attached
hptrr: no controller detected.
ata2: Identifying devices: 00000001
ata2: New devices: 00000001
firewire0: 2 nodes, maxhop <= 1 cable IRM irm(1) (me)
firewire0: bus manager 1
md0: Preloaded image </boot/mfsroot> 4194304 bytes at 0xffffffff8104f9f8
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 480Mbps High Speed USB v2.0
usbus4: 12Mbps Full Speed USB v1.0
usbus5: 12Mbps Full Speed USB v1.0
usbus6: 12Mbps Full Speed USB v1.0
usbus7: 480Mbps High Speed USB v2.0
ata2-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire
ad4: setting UDMA100
ad4: 286188MB <Maxtor 6V300F0 VA111630> at ata2-master UDMA100 SATA 3Gb/s
ad4: 586114704 sectors [581463C/16H/63S] 16 sectors/interrupt 1 depth queue
GEOM: new disk ad4
ugen0.1: <Intel> at usbus0
uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <Intel> at usbus2
uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
ugen3.1: <Intel> at usbus3
uhub3: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus3
ugen4.1: <Intel> at usbus4
uhub4: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4
ugen5.1: <Intel> at usbus5
uhub5: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5
ugen6.1: <Intel> at usbus6
uhub6: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus6
ugen7.1: <Intel> at usbus7
uhub7: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus7
ad4: Intel check1 failed
ad4: Adaptec check1 failed
ad4: LSI (v3) check1 failed
ad4: LSI (v2) check1 failed
ad4: FreeBSD check1 failed
ata3: Identifying devices: 00000001
ata3: New devices: 00000001
ata3-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire
ad6: setting UDMA100
ad6: 476940MB <SAMSUNG HD502HJ 1AJ100E4> at ata3-master UDMA100 SATA 3Gb/s
ad6: 976773168 sectors [969021C/16H/63S] 16 sectors/interrupt 1 depth queue
ad6: Intel check1 failed
ad6: Adaptec check1 failed
ad6: LSI (v3) check1 failed
ad6: LSI (v2) check1 failed
ad6: FreeBSD check1 failed
ata4: Identifying devices: 00000001
ata4: New devices: 00000001
ata4-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire
ad8: setting UDMA100
ad8: 114473MB <Seagate ST3120026AS 3.05> at ata4-master UDMA100 SATA 1.5Gb/s
ad8: 234441648 sectors [232581C/16H/63S] 16 sectors/interrupt 1 depth queue
ad8: Intel check1 failed
ad8: Adaptec check1 failed
ad8: LSI (v3) check1 failed
ad8: LSI (v2) check1 failed
ad8: FreeBSD check1 failed
ata5: Identifying devices: 00000000
ata5: New devices: 00000000
ata6: Identifying devices: 00000001
ata6: New devices: 00000001
ata6-master: pio=PIO4 wdma=WDMA2 udma=UDMA133 cable=40 wire
ad12: setting UDMA100
ad12: 476940MB <SAMSUNG HD502HJ 1AJ100E4> at ata6-master UDMA100 SATA 3Gb/s
ad12: 976773168 sectors [969021C/16H/63S] 16 sectors/interrupt 1 depth queue
ad12: Intel check1 failed
ad12: Adaptec check1 failed
ad12: LSI (v3) check1 failed
ad12: LSI (v2) check1 failed
ad12: FreeBSD check1 failed
ata7: Identifying devices: 00010000
ata7: New devices: 00010000
ata7-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=40 wire
acd0: setting UDMA100
ata7: device_reset timeout=230us
acd0: <ASUS DRW-20B1LT/1.00> DVDR drive at ata7 as master
acd0: read 8269KB/s (8269KB/s) write 8269KB/s (8269KB/s), 2048KB buffer,
UDMA100 SATA 1.5Gb/s
acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet
acd0: Writes: CDR, CDRW, DVDR, DVDRAM, test write, burnproof
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: CD-ROM 120mm data disc
GEOM: new disk ad6
GEOM: new disk ad8
GEOM: new disk ad12
firewire0: New S400 device ID:00902700022b34b9
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub2: 2 ports with 2 removable, self powered
uhub4: 2 ports with 2 removable, self powered
uhub5: 2 ports with 2 removable, self powered
uhub6: 2 ports with 2 removable, self powered
uhub3: 6 ports with 6 removable, self powered
uhub7: 6 ports with 6 removable, self powered
ugen0.2: <ALCOR> at usbus0
uhub8: <ALCOR Generic USB Hub, class 9/0, rev 1.10/3.12, addr 2> on usbus0
(probe1:sbp0:0:1:0): Error 22, Unretryable error
(probe2:sbp0:0:2:0): Error 22, Unretryable error
(probe3:sbp0:0:3:0): Error 22, Unretryable error
(probe0:sbp0:0:0:0): Error 22, Unretryable error
(probe4:sbp0:0:4:0): Error 22, Unretryable error
(probe5:sbp0:0:5:0): Error 22, Unretryable error
(probe6:sbp0:0:6:0): Error 22, Unretryable error
ATA PseudoRAID loaded
SMP: AP CPU #1 Launched!
cpu1 AP:
ID: 0x01000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000200ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010400
SMP: AP CPU #3 Launched!
cpu3 AP:
ID: 0x03000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000200ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010400
SMP: AP CPU #2 Launched!
cpu2 AP:
ID: 0x02000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000200ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010400
ioapic0: routing intpin 3 (ISA fIlRoQw t3a)b lteo cllaepaince r1
svteacrttoerd 4
8
ioapic0: routing intpin 4 (ISA IRQ 4) to lapic 2 vector 48
ioapic0: routing intpin 8 (ISA IRQ 8) to lapic 3 vector 48
ioapic0: routing intpin 16 (PCI IRQ 16) to lapic 1 vector 49
ioapic0: routing intpin 18 (PCI IRQ 18) to lapic 2 vector 49
ioapic0: routing intpin 19 (PCI IRQ 19) to lapic 3 vector 49
ioapic0: routing intpin 21 (PCI IRQ 21) to lapic 1 vector 50
ioapic0: routing intpin 23 (PCI IRQ 23) to lapic 2 vector 50
msi: Assigning MSI IRQ 256 to local APIC 3 vector 50
WARNING: WITNESS option enabled, expect reduced performance.
ugen1.2: <DATACOMP> at usbus1
ukbd0: <DATACOMP SteelSDATA, class 0/0, rev 1.10/0.01, addr 2> on usbus1
kbd2 at ukbd0
kbd2: ukbd0, generic (0), config:0x0, flags:0x3d0000
ums0: <DATACOMP SteelSDATA, class 0/0, rev 1.10/0.01, addr 2> on usbus1
uhub8: 4 ports with 4 removable, self powered
ugen0.3: <SteelSeries ApS> at usbus0
ums1: <SteelSeries ApS Ikari Laser, class 0/0, rev 2.00/1.00, addr 3> on
usbus0
ums1: 7 buttons and [XYZ] coordinates ID=2
acd0: FAILURE - READ_BIG MEDIUM ERROR asc=0x11 ascq=0x05
acd0: FAILURE - READ_BIG MEDIUM ERROR asc=0x11 ascq=0x05
Trying to mount root from ufs:/dev/md0
ct_to_ts([2010-03-28 08:05:57]) = 1269763557.000000000
start_init: trying /sbin/init
start_init: trying /sbin/oinit
start_init: trying /sbin/init.bak
start_init: trying /rescue/init
start_init: trying /stand/sysinstall
Thanks for the help John & *, any chance this will get committed?
More information about the freebsd-hardware
mailing list