Unable to get SIIG PCI serial card to work
Clayton Scott Kern
ckern1 at twcny.rr.com
Fri Mar 17 08:40:29 UTC 2006
on 03-16-2006, John Baldwin wrote:
> On Thursday 16 March 2006 05:24 pm, Clayton Scott Kern wrote:
> > on 03-16-2006, John Baldwin wrote:
> > > Ok, can you get a dmesg from a boot with your custom kernel with puc in
> > > it and the output from kldstat -v with that kernel booted?
> > Here's the info you requested. When not loading the puc module in
> > /boot/loader.conf, the puc device isn't found, though pciconf -lv shows
> > the device. I added the output of pciconf -lv at the end.
> > Output of dmesg
> > Copyright (c) 1992-2005 The FreeBSD Project.
> > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> > The Regents of the University of California. All rights reserved.
> > FreeBSD 6.0-RELEASE-p5 #0: Sat Mar 11 12:12:08 EST 2006
> > root at reddwarf.local:/usr/obj/usr/src/sys/GENERIC
> This kernel doesn't have 'device puc' in it. If it did, it would have the
> 'pci/puc' and 'puc/sio' modules listed in the kldstat -v output. Make sure
> you have built a custom kernel with 'device puc' enabled, installed it, and
> are booting from it.
> > Output of kldstat -v
> > Id Refs Address Size Name
> > 1 11 0xc0400000 63072c kernel
> > Contains modules:
> > Id Name
> > 26 xpt
> > 27 probe
> > 28 cam
> > ...
> No puc this list tells me 'device puc' isn't in this kernel. :)
Thank you for all your help.
I thought I had built and installed the new kernel. This time I did
both and now dmesg shows:
puc0: <Oxford Semiconductor OX16PCI954 UARTs> port
0x9000-0x901f,0x9400-0x941f mem 0xe30
04000-0xe3004fff,0xe3000000-0xe3000fff irq 16 at device 8.0 on pci0
sio1: <Oxford Semiconductor OX16PCI954 UARTs> on puc0
sio1: type 16550A
sio1: unable to activate interrupt in fast mode - using normal mode
sio2: <Oxford Semiconductor OX16PCI954 UARTs> on puc0
sio2: type 16550A
sio2: unable to activate interrupt in fast mode - using normal mode
sio3: <Oxford Semiconductor OX16PCI954 UARTs> on puc0
sio3: type 16550A
sio3: unable to activate interrupt in fast mode - using normal mode
sio4: <Oxford Semiconductor OX16PCI954 UARTs> on puc0
sio4: type 16550A
sio4: unable to activate interrupt in fast mode - using normal mode
and kldstat -v | fgrep puc yields:
Now when I run tip using sio1 - sio4 (aliases for /dev/cuad1-4), I get a message saying connected, but when I press enter, instead of getting my firewall's menu, I get
I rebooted the system into Windoze and it works fine using TerraTerm Pro.
Clayton Scott Kern
ckern1 at twcny.rr.com | The software stated it required
Firewall/UNIX System Administrator | Microsoft Windows 98SE or higher,
PIX, FreeBSD, Linux, Solaris & HP-UX | so I installed FreeBSD
More information about the freebsd-hardware