Unable to get SIIG PCI serial card to work
Clayton Scott Kern
ckern1 at twcny.rr.com
Thu Mar 16 18:41:37 UTC 2006
I've installed a SIIG CyberSerial PCI 16550 RS232 Serial I/O Card, part
no. JJ-P01012 and I can't get it to work.
According to the 6.0_RELEASE Hardware Notes, it appears that this card
is supported.
PCI-Based multi-port serial boards ( puc(4) driver)
Actiontech 56K PCI
Avlab Technology, PCI IO 2S and PCI IO 4S
Comtrol RocketPort 550
Decision Computers PCCOM 4-port serial and dual port RS232/422/485
Dolphin Peripherals 4025/4035/4036
IC Book Labs Dreadnought 16x Lite and Pro
Lava Computers 2SP-PCI/DSerial-PCI/Quattro-PCI/Octopus-550
Middle Digital, Weasle serial port
Moxa Industio CP-114, Smartio C104H-PCI and C168H/PCI
NEC PK-UG-X001 and PK-UG-X008
Netmos NM9835 PCI-2S-550
Oxford Semiconductor OX16PCI954 PCI UART
Syba Tech SD-LAB PCI-4S2P-550-ECP
SIIG Cyber I/O PCI 16C550/16C650/16C850
SIIG Cyber 2P1S PCI 16C550/16C650/16C850
SIIG Cyber 2S1P PCI 16C550/16C650/16C850
SIIG Cyber 4S PCI 16C550/16C650/16C850
SIIG Cyber Serial (Single and Dual) PCI 16C550/16C650/16C850
Syba Tech Ltd. PCI-4S2P-550-ECP
Titan PCI-200H and PCI-800H
US Robotics (3Com) 3CP5609 modem
VScom PCI-400 and PCI-800
Also, /usr/src/sys/dev/puc/pucdata.c implies this card is supported.
First, I added _device puc_ to my kernel config file and built and
installed the new kernel.
When that didn't work, I added _puc_load="YES"_ to /boot/loader and now
the card shows up as puc0, but no sioX. sio0 is used by the onboard
serial port and is being used with an APC SmartUPS 700.
According to sio(4) man page, for single port PCI and PCCARDs use device
sio and that no lines are required in /boot/device.hints.
Where am I going wrong?
I've added the output of pciconf -lv & dmesg, /boot/device.hints and my
kernel config
Output of pciconf -lv
agp0 at pci0:0:0: class=0x060000 card=0x0a851019 chip=0x31161106 rev=0x00 hdr=0x00
vendor = 'VIA Technologies Inc'
device = 'VT8375 ProSavageDDR PM266/KM266 CPU to PCI Bridge'
class = bridge
subclass = HOST-PCI
pcib1 at pci0:1:0: class=0x060400 card=0x00000080 chip=0xb0911106 rev=0x00 hdr=0x01
vendor = 'VIA Technologies Inc'
device = 'VT8633 Apollo Pro 266 CPU to AGP Controller'
class = bridge
subclass = PCI-PCI
puc0 at pci0:8:0: class=0x070006 card=0x2000131f chip=0x950a1415 rev=0x00 hdr=0x00
vendor = 'Oxford Semiconductor Ltd'
device = 'OX16PCI954 Dual PCI UART (??)'
class = simple comms
subclass = UART
none0 at pci0:8:1: class=0x068000 card=0x0000131f chip=0x95101415 rev=0x00 hdr=0x00
vendor = 'Oxford Semiconductor Ltd'
device = 'OX16PCI954 PCI Interface (disabled)'
class = bridge
ahc0 at pci0:9:0: class=0x010000 card=0x00000000 chip=0x60789004 rev=0x01 hdr=0x00
vendor = 'Adaptec Inc'
device = 'AIC-7860 PCI SCSI Controller'
class = mass storage
subclass = SCSI
pcm0 at pci0:10:0: class=0x040100 card=0x100a1102 chip=0x00021102 rev=0x0a hdr=0x00
vendor = 'Creative Labs'
device = 'EMU10000 Sound Blaster Live! (Also Live! 5.1) - OEM from DELL - CT4780'
class = multimedia
subclass = audio
emujoy0 at pci0:10:1: class=0x098000 card=0x00201102 chip=0x70021102 rev=0x0a hdr=0x00
vendor = 'Creative Labs'
device = 'EMU10000 Game Port'
class = input device
rl0 at pci0:14:0: class=0x020000 card=0x813910ec chip=0x813910ec rev=0x10 hdr=0x00
vendor = 'Realtek Semiconductor'
device = 'RT8139 (A/B/C/810x/813x/C+) Fast Ethernet Adapter'
class = network
subclass = ethernet
uhci0 at pci0:16:0: class=0x0c0300 card=0x0a851019 chip=0x30381106 rev=0x80 hdr=0x00
vendor = 'VIA Technologies Inc'
device = 'VT82xxxxx UHCI USB 1.1 Controller (All VIA Chipsets)'
class = serial bus
subclass = USB
uhci1 at pci0:16:1: class=0x0c0300 card=0x0a851019 chip=0x30381106 rev=0x80 hdr=0x00
vendor = 'VIA Technologies Inc'
device = 'VT82xxxxx UHCI USB 1.1 Controller (All VIA Chipsets)'
class = serial bus
subclass = USB
uhci2 at pci0:16:2: class=0x0c0300 card=0x0a851019 chip=0x30381106 rev=0x80 hdr=0x00
vendor = 'VIA Technologies Inc'
device = 'VT82xxxxx UHCI USB 1.1 Controller (All VIA Chipsets)'
class = serial bus
subclass = USB
ehci0 at pci0:16:3: class=0x0c0320 card=0x0a851019 chip=0x31041106 rev=0x82 hdr=0x00
vendor = 'VIA Technologies Inc'
device = 'VT6202 USB 2.0 Enhanced Host Controller'
class = serial bus
subclass = USB
isab0 at pci0:17:0: class=0x060100 card=0x0a851019 chip=0x31771106 rev=0x00 hdr=0x00
vendor = 'VIA Technologies Inc'
device = 'VT8235 PCI to ISA Bridge'
class = bridge
subclass = PCI-ISA
atapci0 at pci0:17:1: class=0x01018a card=0x0a851019 chip=0x05711106 rev=0x06 hdr=0x00
vendor = 'VIA Technologies Inc'
device = 'VT82xxxx EIDE Controller (All VIA Chipsets)'
class = mass storage
subclass = ATA
pcm1 at pci0:17:5: class=0x040100 card=0x0a851019 chip=0x30591106 rev=0x50 hdr=0x00
vendor = 'VIA Technologies Inc'
device = 'VT8233/33A/8235/8237 AC97 Enhanced Audio Controller'
class = multimedia
subclass = audio
none1 at pci1:0:0: class=0x030000 card=0x00000000 chip=0x032610de rev=0xa1 hdr=0x00
vendor = 'NVIDIA Corporation'
device = 'GeForce FX 5500 [NV34.6]'
class = display
subclass = VGA
Output of dmesg
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 6.0-RELEASE-p5 #0: Sat Mar 11 12:12:08 EST 2006
root at reddwarf.local:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: AMD Athlon(tm) XP 2000+ (1662.45-MHz 686-class CPU)
Origin = "AuthenticAMD" Id = 0x681 Stepping = 1
Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
AMD Features=0xc0400800<SYSCALL,MMX+,3DNow+,3DNow>
real memory = 536805376 (511 MB)
avail memory = 515956736 (492 MB)
ACPI APIC Table: <KM266 AWRDACPI>
ioapic0 <Version 0.3> irqs 0-23 on motherboard
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <KM266 AWRDACPI> on motherboard
acpi0: Power Button (fixed)
pci_link0: <ACPI PCI Link LNKA> irq 10 on acpi0
pci_link1: <ACPI PCI Link LNKB> irq 11 on acpi0
pci_link2: <ACPI PCI Link LNKC> irq 3 on acpi0
pci_link3: <ACPI PCI Link LNKD> irq 5 on acpi0
pci_link4: <ACPI PCI Link ALKA> irq 0 on acpi0
pci_link5: <ACPI PCI Link ALKB> irq 0 on acpi0
pci_link6: <ACPI PCI Link ALKC> irq 0 on acpi0
pci_link7: <ACPI PCI Link ALKD> irq 0 on acpi0
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff,0x4000-0x407f,0x4080-0x40ff,0x5000-0x500f on acpi0
pci0: <ACPI PCI bus> on pcib0
agp0: <VIA XM266 (PM266/KM266) host to PCI bridge> mem 0xc0000000-0xcfffffff at device 0.0 on pci0
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <display, VGA> at device 0.0 (no driver attached)
puc0: <Oxford Semiconductor OX16PCI954 UARTs> port 0x9000-0x901f,0x9400-0x941f mem 0xe3004000-0xe3004fff,0xe3000000-0xe3000fff irq 16 at device 8.0 on pci0
pci0: <bridge> at device 8.1 (no driver attached)
ahc0: <Adaptec aic7860 Ultra SCSI adapter> port 0xa000-0xa0ff mem 0xe3003000-0xe3003fff irq 17 at device 9.0 on pci0
ahc0: [GIANT-LOCKED]
aic7860: Ultra Single Channel A, SCSI Id=7, 3/253 SCBs
pcm0: <Creative EMU10K1> port 0xa400-0xa41f irq 18 at device 10.0 on pci0
pcm0: <SigmaTel STAC9708/11 AC97 Codec>
rl0: <RealTek 8139 10/100BaseTX> port 0xac00-0xacff mem 0xe3005000-0xe30050ff irq 19 at device 14.0 on pci0
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: Ethernet address: 00:0a:e6:df:5c:ec
uhci0: <VIA 83C572 USB controller> port 0xb000-0xb01f irq 21 at device 16.0 on pci0
uhci0: [GIANT-LOCKED]
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <VIA 83C572 USB controller> port 0xb400-0xb41f irq 21 at device 16.1 on pci0
uhci1: [GIANT-LOCKED]
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <VIA 83C572 USB controller> port 0xb800-0xb81f irq 21 at device 16.2 on pci0
uhci2: [GIANT-LOCKED]
usb2: <VIA 83C572 USB controller> on uhci2
usb2: USB revision 1.0
uhub2: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ehci0: <VIA VT6202 USB 2.0 controller> mem 0xe3006000-0xe30060ff irq 21 at device 16.3 on pci0
ehci0: [GIANT-LOCKED]
usb3: EHCI version 1.0
usb3: companion controllers, 2 ports each: usb0 usb1 usb2
usb3: <VIA VT6202 USB 2.0 controller> on ehci0
usb3: USB revision 2.0
uhub3: VIA EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered
umass0: vendor 0x05e3 USB 2.0 Card Reader, rev 2.00/1.28, addr 2
isab0: <PCI-ISA bridge> at device 17.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 8235 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xbc00-0xbc0f at device 17.1 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
pcm1: <VIA VT8235> port 0xc000-0xc0ff irq 22 at device 17.5 on pci0
pcm1: [GIANT-LOCKED]
pcm1: <Avance Logic ALC200 AC97 Codec>
acpi_tz0: <Thermal Zone> on acpi0
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
ppc0: <ECP parallel printer port> port 0x378-0x37f,0x778-0x77b irq 7 drq 3 on acpi0
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/16 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model MouseMan+, device ID 0
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xcf7ff,0xd0000-0xd7fff,0xd8000-0xd87ff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
umass1: MITSUMI MITSUMI USB FDD, rev 1.10/1.00, addr 2
Timecounter "TSC" frequency 1662452640 Hz quality 800
Timecounters tick every 1.000 msec
ipfw2 (+ipv6) initialized, divert loadable, rule-based forwarding disabled, default to deny, logging disabled
Waiting 5 seconds for SCSI devices to settle
ad0: 39266MB <IC35L040AVVA07 0 VA2OA52A> at ata0-master UDMA100
acd0: CDRW <LITE-ON LTR-52327S/QS5A> at ata0-slave UDMA33
ad2: 19574MB <WDC WD205BA 16.13M16> at ata1-master UDMA66
ad3: 19574MB <WDC WD205BA 16.13M16> at ata1-slave UDMA66
sa0 at ahc0 bus 0 target 6 lun 0
sa0: <ARCHIVE Python 28849-XXX 4.CM> Removable Sequential Access SCSI-2 device
sa0: 5.000MB/s transfers (5.000MHz, offset 15)
ch0 at ahc0 bus 0 target 6 lun 1
ch0: <ARCHIVE Python 28849-XXX 4.CM> Removable Changer SCSI-2 device
ch0: 5.000MB/s transfers (5.000MHz, offset 15)
ch0: 4 slots, 1 drive, 1 picker, 0 portals
da0 at ahc0 bus 0 target 5 lun 0
da0: <IOMEGA ZIP 100 J.03> Removable Direct Access SCSI-2 device
da0: 3.300MB/s transfers
da0: Attempt to query device size failed: NOT READY, Medium not present
da1 at umass-sim0 bus 0 target 0 lun 0
da1: <Generic STORAGE DEVICE 0128> Removable Direct Access SCSI-0 device
da1: 40.000MB/s transfers
da1: Attempt to query device size failed: NOT READY, Medium not present
(da0:ahc0:0:5:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0
(da0:ahc0:0:5:0): CAM Status: SCSI Status Error
(da0:ahc0:0:5:0): SCSI Status: Check Condition
(da0:ahc0:0:5:0): NOT READY asc:3a,0
(da0:ahc0:0:5:0): Medium not present
(da0:ahc0:0:5:0): Unretryable error
Opened disk da0 -> 6
(da0:ahc0:0:5:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0
(da0:ahc0:0:5:0): CAM Status: SCSI Status Error
(da0:ahc0:0:5:0): SCSI Status: Check Condition
(da0:ahc0:0:5:0): NOT READY asc:3a,0
(da0:ahc0:0:5:0): Medium not present
(da0:ahc0:0:5:0): Unretryable error
Opened disk da0 -> 6
da5 at umass-sim1 bus 1 target 0 lun 0
da5: <MITSUMI USB FDD 066M 2.05> Removable Direct Access SCSI-0 device
da5: 1.000MB/s transfers
da5: Attempt to query device size failed: NOT READY, Medium not present
da2 at umass-sim0 bus 0 target 0 lun 1
da2: <Generic STORAGE DEVICE 0128> Removable Direct Access SCSI-0 device
da2: 40.000MB/s transfers
da2: Attempt to query device size failed: NOT READY, Medium not present
(da0:ahc0:0:5:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0
(da0:ahc0:0:5:0): CAM Status: SCSI Status Error
(da0:ahc0:0:5:0): SCSI Status: Check Condition
(da0:ahc0:0:5:0): NOT READY asc:3a,0
(da0:ahc0:0:5:0): Medium not present
(da0:ahc0:0:5:0): Unretryable error
Opened disk da0 -> 6
da3 at umass-sim0 bus 0 target 0 lun 2
da3: <Generic STORAGE DEVICE 0128> Removable Direct Access SCSI-0 device
da3: 40.000MB/s transfers
da3: Attempt to query device size failed: NOT READY, Medium not present
da4 at umass-sim0 bus 0 target 0 lun 3
da4: <Generic STORAGE DEVICE 0128> Removable Direct Access SCSI-0 device
da4: 40.000MB/s transfers
da4: Attempt to query device size failed: NOT READY, Medium not present
(da1:umass-sim0:0:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0
(da1:umass-sim0:0:0:0): CAM Status: SCSI Status Error
(da1:umass-sim0:0:0:0): SCSI Status: Check Condition
(da1:umass-sim0:0:0:0): NOT READY asc:3a,0
(da1:umass-sim0:0:0:0): Medium not present
(da1:umass-sim0:0:0:0): Unretryable error
Opened disk da1 -> 6
(da1:umass-sim0:0:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0
(da1:umass-sim0:0:0:0): CAM Status: SCSI Status Error
(da1:umass-sim0:0:0:0): SCSI Status: Check Condition
(da1:umass-sim0:0:0:0): NOT READY asc:3a,0
(da1:umass-sim0:0:0:0): Medium not present
(da1:umass-sim0:0:0:0): Unretryable error
Opened disk da1 -> 6
(da1:umass-sim0:0:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0
(da1:umass-sim0:0:0:0): CAM Status: SCSI Status Error
(da1:umass-sim0:0:0:0): SCSI Status: Check Condition
(da1:umass-sim0:0:0:0): NOT READY asc:3a,0
(da1:umass-sim0:0:0:0): Medium not present
(da1:umass-sim0:0:0:0): Unretryable error
Opened disk da1 -> 6
(da2:umass-sim0:0:0:1): READ CAPACITY. CDB: 25 20 0 0 0 0 0 0 0 0
(da2:umass-sim0:0:0:1): CAM Status: SCSI Status Error
(da2:umass-sim0:0:0:1): SCSI Status: Check Condition
(da2:umass-sim0:0:0:1): NOT READY asc:3a,0
(da2:umass-sim0:0:0:1): Medium not present
(da2:umass-sim0:0:0:1): Unretryable error
Opened disk da2 -> 6
(da2:umass-sim0:0:0:1): READ CAPACITY. CDB: 25 20 0 0 0 0 0 0 0 0
(da2:umass-sim0:0:0:1): CAM Status: SCSI Status Error
(da2:umass-sim0:0:0:1): SCSI Status: Check Condition
(da2:umass-sim0:0:0:1): NOT READY asc:3a,0
(da2:umass-sim0:0:0:1): Medium not present
(da2:umass-sim0:0:0:1): Unretryable error
Opened disk da2 -> 6
(da2:umass-sim0:0:0:1): READ CAPACITY. CDB: 25 20 0 0 0 0 0 0 0 0
(da2:umass-sim0:0:0:1): CAM Status: SCSI Status Error
(da2:umass-sim0:0:0:1): SCSI Status: Check Condition
(da2:umass-sim0:0:0:1): NOT READY asc:3a,0
(da2:umass-sim0:0:0:1): Medium not present
(da2:umass-sim0:0:0:1): Unretryable error
Opened disk da2 -> 6
(da3:umass-sim0:0:0:2): READ CAPACITY. CDB: 25 40 0 0 0 0 0 0 0 0
(da3:umass-sim0:0:0:2): CAM Status: SCSI Status Error
(da3:umass-sim0:0:0:2): SCSI Status: Check Condition
(da3:umass-sim0:0:0:2): NOT READY asc:3a,0
(da3:umass-sim0:0:0:2): Medium not present
(da3:umass-sim0:0:0:2): Unretryable error
Opened disk da3 -> 6
(da3:umass-sim0:0:0:2): READ CAPACITY. CDB: 25 40 0 0 0 0 0 0 0 0
(da3:umass-sim0:0:0:2): CAM Status: SCSI Status Error
(da3:umass-sim0:0:0:2): SCSI Status: Check Condition
(da3:umass-sim0:0:0:2): NOT READY asc:3a,0
(da3:umass-sim0:0:0:2): Medium not present
(da3:umass-sim0:0:0:2): Unretryable error
Opened disk da3 -> 6
(da3:umass-sim0:0:0:2): READ CAPACITY. CDB: 25 40 0 0 0 0 0 0 0 0
(da3:umass-sim0:0:0:2): CAM Status: SCSI Status Error
(da3:umass-sim0:0:0:2): SCSI Status: Check Condition
(da3:umass-sim0:0:0:2): NOT READY asc:3a,0
(da3:umass-sim0:0:0:2): Medium not present
(da3:umass-sim0:0:0:2): Unretryable error
Opened disk da3 -> 6
(da4:umass-sim0:0:0:3): READ CAPACITY. CDB: 25 60 0 0 0 0 0 0 0 0
(da4:umass-sim0:0:0:3): CAM Status: SCSI Status Error
(da4:umass-sim0:0:0:3): SCSI Status: Check Condition
(da4:umass-sim0:0:0:3): NOT READY asc:3a,0
(da4:umass-sim0:0:0:3): Medium not present
(da4:umass-sim0:0:0:3): Unretryable error
Opened disk da4 -> 6
(da4:umass-sim0:0:0:3): READ CAPACITY. CDB: 25 60 0 0 0 0 0 0 0 0
(da4:umass-sim0:0:0:3): CAM Status: SCSI Status Error
(da4:umass-sim0:0:0:3): SCSI Status: Check Condition
(da4:umass-sim0:0:0:3): NOT READY asc:3a,0
(da4:umass-sim0:0:0:3): Medium not present
(da4:umass-sim0:0:0:3): Unretryable error
Opened disk da4 -> 6
(da4:umass-sim0:0:0:3): READ CAPACITY. CDB: 25 60 0 0 0 0 0 0 0 0
(da4:umass-sim0:0:0:3): CAM Status: SCSI Status Error
(da4:umass-sim0:0:0:3): SCSI Status: Check Condition
(da4:umass-sim0:0:0:3): NOT READY asc:3a,0
(da4:umass-sim0:0:0:3): Medium not present
(da4:umass-sim0:0:0:3): Unretryable error
Opened disk da4 -> 6
(da5:umass-sim1:1:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0
(da5:umass-sim1:1:0:0): CAM Status: SCSI Status Error
(da5:umass-sim1:1:0:0): SCSI Status: Check Condition
(da5:umass-sim1:1:0:0): NOT READY asc:3a,0
(da5:umass-sim1:1:0:0): Medium not present
(da5:umass-sim1:1:0:0): Unretryable error
Opened disk da5 -> 6
(da5:umass-sim1:1:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0
(da5:umass-sim1:1:0:0): CAM Status: SCSI Status Error
(da5:umass-sim1:1:0:0): SCSI Status: Check Condition
(da5:umass-sim1:1:0:0): NOT READY asc:3a,0
(da5:umass-sim1:1:0:0): Medium not present
(da5:umass-sim1:1:0:0): Unretryable error
Opened disk da5 -> 6
(da5:umass-sim1:1:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0
(da5:umass-sim1:1:0:0): CAM Status: SCSI Status Error
(da5:umass-sim1:1:0:0): SCSI Status: Check Condition
(da5:umass-sim1:1:0:0): NOT READY asc:3a,0
(da5:umass-sim1:1:0:0): Medium not present
(da5:umass-sim1:1:0:0): Unretryable error
Opened disk da5 -> 6
Trying to mount root from ufs:/dev/ad2s1a
# $FreeBSD: src/sys/i386/conf/GENERIC.hints,v 1.14 2005/01/14 06:54:59 imp Exp $
hint.fdc.0.at="isa"
hint.fdc.0.port="0x3F0"
hint.fdc.0.irq="6"
hint.fdc.0.drq="2"
hint.fd.0.at="fdc0"
hint.fd.0.drive="0"
hint.fd.1.at="fdc0"
hint.fd.1.drive="1"
hint.ata.0.at="isa"
hint.ata.0.port="0x1F0"
hint.ata.0.irq="14"
hint.ata.1.at="isa"
hint.ata.1.port="0x170"
hint.ata.1.irq="15"
hint.adv.0.at="isa"
hint.adv.0.disabled="1"
hint.bt.0.at="isa"
hint.bt.0.disabled="1"
hint.aha.0.at="isa"
hint.aha.0.disabled="1"
hint.aic.0.at="isa"
hint.aic.0.disabled="1"
hint.atkbdc.0.at="isa"
hint.atkbdc.0.port="0x060"
hint.atkbd.0.at="atkbdc"
hint.atkbd.0.irq="1"
hint.psm.0.at="atkbdc"
hint.psm.0.irq="12"
hint.vga.0.at="isa"
hint.sc.0.at="isa"
hint.sc.0.flags="0x100"
hint.vt.0.at="isa"
hint.vt.0.disabled="1"
hint.apm.0.disabled="1"
hint.apm.0.flags="0x20"
hint.sio.0.at="isa"
hint.sio.0.port="0x3F8"
hint.sio.0.flags="0x10"
hint.sio.0.irq="4"
hint.ppc.0.at="isa"
hint.ppc.0.irq="7"
hint.ed.0.at="isa"
hint.ed.0.disabled="1"
hint.ed.0.port="0x280"
hint.ed.0.irq="10"
hint.ed.0.maddr="0xd8000"
hint.cs.0.at="isa"
hint.cs.0.disabled="1"
hint.cs.0.port="0x300"
hint.sn.0.at="isa"
hint.sn.0.disabled="1"
hint.sn.0.port="0x300"
hint.sn.0.irq="10"
hint.ie.0.at="isa"
hint.ie.0.disabled="1"
hint.ie.0.port="0x300"
hint.ie.0.irq="10"
hint.ie.0.maddr="0xd0000"
hint.fe.0.at="isa"
hint.fe.0.disabled="1"
hint.fe.0.port="0x300"
hint.lnc.0.at="isa"
hint.lnc.0.disabled="1"
hint.lnc.0.port="0x280"
hint.lnc.0.irq="10"
hint.lnc.0.drq="0"
#
# REDDWARF -- kernel configuration file for reddwarf
#
# For more information on this file, please read the handbook section on
# Kernel Configuration Files:
#
# http://www.FreeBSD.org/doc/en_US.ISO8859-1/books/handbook/kernelconfig-config.html
#
# The handbook is also available locally in /usr/share/doc/handbook
# if you've installed the doc distribution, otherwise always see the
# FreeBSD World Wide Web server (http://www.FreeBSD.org/) for the
# latest information.
#
# An exhaustive list of options and more detailed explanations of the
# device lines is also present in the ../../conf/NOTES and NOTES files.
# If you are in doubt as to the purpose or necessity of a line, check first
# in NOTES.
machine i386
cpu I486_CPU
cpu I586_CPU
cpu I686_CPU
ident REDDWARF
# To statically compile in device wiring instead of /boot/device.hints
#hints "GENERIC.hints" # Default places to look for devices.
makeoptions DEBUG=-g # Build kernel with gdb(1) debug symbols
#options SCHED_ULE # ULE scheduler
options SCHED_4BSD # 4BSD scheduler
options PREEMPTION # Enable kernel thread preemption
options INET # InterNETworking
options INET6 # IPv6 communications protocols
options FFS # Berkeley Fast Filesystem
options SOFTUPDATES # Enable FFS soft updates support
options UFS_ACL # Support for access control lists
options UFS_DIRHASH # Improve performance on big directories
options MD_ROOT # MD is a potential root device
options NFSCLIENT # Network Filesystem Client
options NFSSERVER # Network Filesystem Server
options NFS_ROOT # NFS usable as /, requires NFSCLIENT
options MSDOSFS # MSDOS Filesystem
options CD9660 # ISO 9660 Filesystem
options PROCFS # Process filesystem (requires PSEUDOFS)
options PSEUDOFS # Pseudo-filesystem framework
options GEOM_GPT # GUID Partition Tables.
options COMPAT_43 # Compatible with BSD 4.3 [KEEP THIS!]
options COMPAT_FREEBSD4 # Compatible with FreeBSD4
options COMPAT_FREEBSD5 # Compatible with FreeBSD5
options SCSI_DELAY=5000 # Delay (in ms) before probing SCSI
options KTRACE # ktrace(1) support
options SYSVSHM # SYSV-style shared memory
options SYSVMSG # SYSV-style message queues
options SYSVSEM # SYSV-style semaphores
options _KPOSIX_PRIORITY_SCHEDULING # POSIX P1003_1B real-time extensions
options KBD_INSTALL_CDEV # install a CDEV entry in /dev
options AHC_REG_PRETTY_PRINT # Print register bitfields in debug
# output. Adds ~128k to driver.
options AHD_REG_PRETTY_PRINT # Print register bitfields in debug
# output. Adds ~215k to driver.
options ADAPTIVE_GIANT # Giant mutex is adaptive.
device apic # I/O APIC
# Bus support.
device eisa
device pci
# Floppy drives
device fdc
# ATA and ATAPI devices
device ata
device atadisk # ATA disk drives
device ataraid # ATA RAID drives
device atapicd # ATAPI CDROM drives
device atapifd # ATAPI floppy drives
device atapist # ATAPI tape drives
options ATA_STATIC_ID # Static device numbering
# SCSI Controllers
device ahb # EISA AHA1742 family
device ahc # AHA2940 and onboard AIC7xxx devices
device ahd # AHA39320/29320 and onboard AIC79xx devices
device amd # AMD 53C974 (Tekram DC-390(T))
device isp # Qlogic family
#device ispfw # Firmware for QLogic HBAs- normally a module
device mpt # LSI-Logic MPT-Fusion
#device ncr # NCR/Symbios Logic
device sym # NCR/Symbios Logic (newer chipsets + those of `ncr')
device trm # Tekram DC395U/UW/F DC315U adapters
device adv # Advansys SCSI adapters
device adw # Advansys wide SCSI adapters
device aha # Adaptec 154x SCSI adapters
device aic # Adaptec 15[012]x SCSI adapters, AIC-6[23]60.
device bt # Buslogic/Mylex MultiMaster SCSI adapters
device ncv # NCR 53C500
device nsp # Workbit Ninja SCSI-3
device stg # TMC 18C30/18C50
# SCSI peripherals
device scbus # SCSI bus (required for SCSI)
device ch # SCSI media changers
device da # Direct Access (disks)
device sa # Sequential Access (tape etc)
device cd # CD
device pass # Passthrough device (direct SCSI access)
device ses # SCSI Environmental Services (and SAF-TE)
# RAID controllers interfaced to the SCSI subsystem
device amr # AMI MegaRAID
device arcmsr # Areca SATA II RAID
device asr # DPT SmartRAID V, VI and Adaptec SCSI RAID
device ciss # Compaq Smart RAID 5*
device dpt # DPT Smartcache III, IV - See NOTES for options
device hptmv # Highpoint RocketRAID 182x
device iir # Intel Integrated RAID
device ips # IBM (Adaptec) ServeRAID
device mly # Mylex AcceleRAID/eXtremeRAID
device twa # 3ware 9000 series PATA/SATA RAID
# RAID controllers
device aac # Adaptec FSA RAID
device aacp # SCSI passthrough for aac (requires CAM)
device ida # Compaq Smart RAID
device mlx # Mylex DAC960 family
device pst # Promise Supertrak SX6000
device twe # 3ware ATA RAID
# atkbdc0 controls both the keyboard and the PS/2 mouse
device atkbdc # AT keyboard controller
device atkbd # AT keyboard
device psm # PS/2 mouse
device vga # VGA video card driver
device splash # Splash screen and screen saver support
# syscons is the default console driver, resembling an SCO console
device sc
# Enable this for the pcvt (VT220 compatible) console driver
#device vt
#options XSERVER # support for X server on a vt console
#options FAT_CURSOR # start with block cursor
device agp # support several AGP chipsets
# Power management support (see NOTES for more options)
#device apm
# Add suspend/resume support for the i8254.
device pmtimer
# PCCARD (PCMCIA) support
# PCMCIA and cardbus bridge support
device cbb # cardbus (yenta) bridge
device pccard # PC Card (16-bit) bus
device cardbus # CardBus (32-bit) bus
# Serial (COM) ports
device sio # 8250, 16[45]50 based serial ports
# Parallel port
device ppc
device ppbus # Parallel port bus (required)
device lpt # Printer
device plip # TCP/IP over parallel
device ppi # Parallel port interface device
#device vpo # Requires scbus and da
# If you've got a "dumb" serial or parallel PCI card that is
# supported by the puc(4) glue driver, uncomment the following
# line to enable it (connects to the sio and/or ppc drivers):
device puc
# PCI Ethernet NICs.
device de # DEC/Intel DC21x4x (``Tulip'')
device em # Intel PRO/1000 adapter Gigabit Ethernet Card
device ixgb # Intel PRO/10GbE Ethernet Card
device txp # 3Com 3cR990 (``Typhoon'')
device vx # 3Com 3c590, 3c595 (``Vortex'')
# PCI Ethernet NICs that use the common MII bus controller code.
# NOTE: Be sure to keep the 'device miibus' line in order to use these NICs!
device miibus # MII bus support
device bfe # Broadcom BCM440x 10/100 Ethernet
device bge # Broadcom BCM570xx Gigabit Ethernet
device dc # DEC/Intel 21143 and various workalikes
device fxp # Intel EtherExpress PRO/100B (82557, 82558)
device lge # Level 1 LXT1001 gigabit Ethernet
device nge # NatSemi DP83820 gigabit Ethernet
device nve # nVidia nForce MCP on-board Ethernet Networking
device pcn # AMD Am79C97x PCI 10/100(precedence over 'lnc')
device re # RealTek 8139C+/8169/8169S/8110S
device rl # RealTek 8129/8139
device sf # Adaptec AIC-6915 (``Starfire'')
device sis # Silicon Integrated Systems SiS 900/SiS 7016
device sk # SysKonnect SK-984x & SK-982x gigabit Ethernet
device ste # Sundance ST201 (D-Link DFE-550TX)
device ti # Alteon Networks Tigon I/II gigabit Ethernet
device tl # Texas Instruments ThunderLAN
device tx # SMC EtherPower II (83c170 ``EPIC'')
device vge # VIA VT612x gigabit Ethernet
device vr # VIA Rhine, Rhine II
device wb # Winbond W89C840F
device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'')
# ISA Ethernet NICs. pccard NICs included.
device cs # Crystal Semiconductor CS89x0 NIC
# 'device ed' requires 'device miibus'
device ed # NE[12]000, SMC Ultra, 3c503, DS8390 cards
device ex # Intel EtherExpress Pro/10 and Pro/10+
device ep # Etherlink III based cards
device fe # Fujitsu MB8696x based cards
device ie # EtherExpress 8/16, 3C507, StarLAN 10 etc.
device lnc # NE2100, NE32-VL Lance Ethernet cards
device sn # SMC's 9000 series of Ethernet chips
device xe # Xircom pccard Ethernet
# ISA devices that use the old ISA shims
#device le
# Wireless NIC cards
device wlan # 802.11 support
device an # Aironet 4500/4800 802.11 wireless NICs.
device awi # BayStack 660 and others
device ral # Ralink Technology RT2500 wireless NICs.
device wi # WaveLAN/Intersil/Symbol 802.11 wireless NICs.
#device wl # Older non 802.11 Wavelan wireless NIC.
# Pseudo devices.
device loop # Network loopback
device random # Entropy device
device ether # Ethernet support
device sl # Kernel SLIP
device ppp # Kernel PPP
device tun # Packet tunnel.
device pty # Pseudo-ttys (telnet etc)
device md # Memory "disks"
device gif # IPv6 and IPv4 tunneling
device faith # IPv6-to-IPv4 relaying (translation)
# The `bpf' device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
# Note that 'bpf' is required for DHCP.
device bpf # Berkeley packet filter
# USB support
device uhci # UHCI PCI->USB interface
device ohci # OHCI PCI->USB interface
device ehci # EHCI PCI->USB interface (USB 2.0)
device usb # USB Bus (required)
#device udbp # USB Double Bulk Pipe devices
device ugen # Generic
#device uhid # "Human Interface Devices"
device ukbd # Keyboard
device ulpt # Printer
device umass # Disks/Mass storage - Requires scbus and da
device ums # Mouse
device ural # Ralink Technology RT2500USB wireless NICs
device urio # Diamond Rio 500 MP3 player
device uscanner # Scanners
# USB Ethernet, requires miibus
device aue # ADMtek USB Ethernet
device axe # ASIX Electronics USB Ethernet
device cdce # Generic USB over Ethernet
device cue # CATC USB Ethernet
device kue # Kawasaki LSI USB Ethernet
device rue # RealTek RTL8150 USB Ethernet
# FireWire support
device firewire # FireWire bus code
device sbp # SCSI over FireWire (Requires scbus and da)
device fwe # Ethernet over FireWire (non-standard!)
--
Clayton Scott Kern
ckern1 at twcny.rr.com | The software stated it required
Firewall/UNIX System Administrator | Microsoft Windows 98SE or higher,
PIX, FreeBSD, Linux, Solaris & HP-UX | so I installed FreeBSD
More information about the freebsd-hardware
mailing list