Problem with FastTrak S150 SX4-M

Travis L. Leuthauser travis at
Tue Jan 25 08:03:17 PST 2005

I'm trying to load 5.3 Release on a P3 1GHz machine with the FastTrak S150
installed.  Attached is the output from a failed boot.  It appears the card
is being detected and probed, but when the drives are probed there is a
panic.  Any ideas would be greatly appreciated.


++++++ Boot Output

Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 5.3-RELEASE #0: Fri Nov  5 04:19:18 UTC 2004
    root at
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel Pentium III (996.77-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x686  Stepping = 6
real memory  = 132907008 (126 MB)
avail memory = 116318208 (110 MB)
pnpbios: Bad PnP BIOS data checksum
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <DELL MUMMY> on motherboard
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
cpu0: <ACPI CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
agp0: <Intel 82810E (i810E GMCH) SVGA controller> mem
0xffa80000-0xffafffff,0xf8000000-0xfbffffff irq 11 at device 1.0 on pci0
pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci1: <ACPI PCI bus> on pcib1
atapci0: <Promise PDC20622 SATA150 controller> port
0xd000-0xd0ff,0xd400-0xd4ff,0xd800-0xd8ff mem
0xff7f8000-0xff7fffff,0xff800000-0xff8fffff irq 10 at device 9.0 on pci1
atapci0: failed: rid 0x20 is memory, requested 4
atapci0: DIMM size 64MB @ 0x00000000 ECC enabled
ata2: channel #0 on atapci0
ata3: channel #1 on atapci0
ata4: channel #2 on atapci0
ata5: channel #3 on atapci0
xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xdc00-0xdc7f mem
0xff7f7c00-0xff7f7c7f irq 9 at device 11.0 on pci1
miibus0: <MII bus> on xl0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl0: Ethernet address: 00:04:76:37:48:21
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci1: <Intel ICH UDMA66 controller> port
0xffa0-0xffaf,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 31.1 on pci0
ata0: channel #0 on atapci1
ata1: channel #1 on atapci1
uhci0: <Intel 82801AA (ICH) USB controller> port 0xef80-0xef9f irq 9 at
device 31.2 on pci0
usb0: <Intel 82801AA (ICH) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
fdc0: <floppy drive controller> port
0x3f7,0x3f4-0x3f5,0x3f2-0x3f3,0x3f0-0x3f1 irq 6 drq 2 on acpi0
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on
sio0: type 16550A, console
ppc0: <ECP parallel printer port> port 0x778-0x77f,0x378-0x37f irq 7 drq 3
on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
orm0: <ISA Option ROMs> at iomem
0xd8800-0xd8fff,0xcc000-0xd87ff,0xc0000-0xcbfff on isa0
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 996770690 Hz quality 800
Timecounters tick every 10.000 msec
md0: Preloaded image </boot/mfsroot> 4423680 bytes at 0xc09cdad0
acd0: CDRW <Memorex 48MAXX 1248AJ/VWS4> at ata0-master UDMA33
ata2-master: FAILURE - ATA_IDENTIFY timed out
ata2-master: FAILURE - ATA_IDENTIFY timed out

Fatal trap 12: page fault while in kernel mode
fault virtual address   = 0x6
fault code              = supervisor read, page not present
instruction pointer     = 0x8:0xc04c1430
stack pointer           = 0x10:0xc1021d38
frame pointer           = 0x10:0xc1021d60
code segment            = base 0x0, limit 0xfffff, type 0x1b
                        = DPL 0, pres 1, def32 1, gran 1
processor eflags        = interrupt enabled, resume, IOPL = 0
current process         = 0 (swapper)
trap number             = 12
panic: page fault
Uptime: 17s
Cannot dump. No dump device defined.
Shutting down ACPI

More information about the freebsd-hardware mailing list