Any known issues regarding VIA IDE chips?
Tony Frank
tfrank at optushome.com.au
Mon Feb 23 03:54:53 PST 2004
Hi,
I am having trouble with a Aplus motherboard I have.
Board is based around VIA 82C691 chipset with VIA 82C586B IDE chip.
ata(4) shows the chip as being supported.
While it's detected and my drives appear I keep getting messages:
ad0: WRITE command timeout tag=0 serv=0 - resetting
ata0: resetting devices .. ata0: mask=03 ostat0=58 ostat2=00
ad0: ATAPI 00 00
ata0-slave: ATAPI 00 00
ata0: mask=03 stat0=50 stat1=00
ad0: ATA 01 a5
ata0: devices=01
ad0: success setting UDMA2 on VIA chip
This happens also for ad2.
When this occurs the system 'freezes' until the ATA reset etc is completed.
Cables & drives work just fine on intel 440BX board.
Have swapped 'basic' cables with UDMA66 rated cables (despite drives &
board only being rated for ATA33)
dmesg briefly:
atapci0: <VIA 82C586 ATA33 controller> port 0xd000-0xd00f at device 7.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
[ ... ]
ad0: success setting UDMA2 on VIA chip
Creating DISK ad0
ar: FreeBSD check1 failed
ad0: <FUJITSU MPE3084AE/EE-C0-23> ATA-4 disk at ata0-master
ad0: 8063MB (16514064 sectors), 16383 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA33
ad0: piomode=4 dmamode=2 udmamode=4 cblid=1
ad2: success setting UDMA2 on VIA chip
Creating DISK ad2
ar: FreeBSD check1 failed
ad2: <FUJITSU MPC3032AT/6021> ATA-3 disk at ata1-master
ad2: 3093MB (6335280 sectors), 6704 C, 15 H, 63 S, 512 B
ad2: 16 secs/int, 1 depth queue, UDMA33
ad2: piomode=4 dmamode=2 udmamode=2 cblid=0
FreeBSD version:
FreeBSD 4.9-RELEASE #0: Mon Oct 27 17:51:09 GMT 2003
root at freebsd-stable.sentex.ca:/usr/obj/usr/src/sys/GENERIC
In meantime I will attempt disabling dma via sysctl and then
I guess also review -STABLE to see how many ATA fixes were made
since 4.9-RELEASE.
Any extra ideas will be appreciated!
Verbose boot messages below:
SMAP type=01 base=0000000000000000 len=000000000009fc00
SMAP type=02 base=000000000009fc00 len=0000000000000400
SMAP type=02 base=00000000000f0000 len=0000000000010000
SMAP type=02 base=00000000ffff0000 len=0000000000010000
SMAP type=01 base=0000000000100000 len=0000000007ef0000
SMAP type=03 base=0000000007ff3000 len=000000000000d000
SMAP type=04 base=0000000007ff0000 len=0000000000003000
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.9-RELEASE #0: Mon Oct 27 17:51:09 GMT 2003
root at freebsd-stable.sentex.ca:/usr/obj/usr/src/sys/GENERIC
Calibrating clock(s) ... TSC clock: 267248865 Hz, i8254 clock: 1193075 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
CPU: Pentium II/Pentium II Xeon/Celeron (267.27-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x633 Stepping = 3
Features=0x80f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,MMX
>
real memory = 134152192 (131008K bytes)
Physical memory chunk(s):
0x000001000 - 0x00009efff, 647168 bytes (158 pages)
0x000566000 - 0x007fe7fff, 128458752 bytes (31362 pages)
config> en apm0
avail memory = 125194240 (122260K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00fac60
bios32: Entry = 0xfb0e0 (c00fb0e0) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xb110
pnpbios: Found PnP BIOS data at 0xc00fbdf0
pnpbios: Entry = f0000:be18 Rev = 1.0
Other BIOS signatures found:
ACPI: 000f7d30
Preloaded elf kernel "kernel" at 0xc053f000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc053f09c.
Pentium Pro MTRR support enabled
Creating DISK md0
md0: Malloc disk
Math emulator present
pci_open(1): mode 1 addr port (0x0cf8) is 0x80000060
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=06911106)
Using $PIR table, 7 entries at 0xc00fdc40
pcib-: pcib0 exists, using next available unit number
apm0: <APM BIOS> on motherboard
apm0: found APM BIOS v1.2, connected at v1.2
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
found-> vendor=0x1106, dev=0x0691, revid=0x01
class=06-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[10]: type 1, range 32, base d0000000, size 26
found-> vendor=0x1106, dev=0x8598, revid=0x00
class=06-04-00, hdrtype=0x01, mfdev=0
subordinatebus=1 secondarybus=1
found-> vendor=0x1106, dev=0x0586, revid=0x41
class=06-01-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x1106, dev=0x0571, revid=0x06
class=01-01-8a, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[20]: type 1, range 32, base 0000d000, size 4
found-> vendor=0x1106, dev=0x3038, revid=0x02
class=0c-03-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=d, irq=11
map[20]: type 1, range 32, base 0000d400, size 5
found-> vendor=0x1106, dev=0x3040, revid=0x10
class=06-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
found-> vendor=0x8086, dev=0x1229, revid=0x08
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=10
map[10]: type 1, range 32, base d6100000, size 12
map[14]: type 1, range 32, base 0000d800, size 6
map[18]: type 1, range 32, base d6000000, size 20
found-> vendor=0x1002, dev=0x4754, revid=0x48
class=03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[10]: type 1, range 32, base d5000000, size 24
map[14]: type 1, range 32, base 0000dc00, size 8
found-> vendor=0x9004, dev=0x8178, revid=0x01
class=01-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=5
map[10]: type 1, range 32, base 0000e000, size 8
map[14]: type 1, range 32, base d6101000, size 12
pci0: <PCI bus> on pcib0
agp0: <VIA 82C691 (Apollo Pro) host to PCI bridge> mem 0xd0000000-0xd3ffffff at
device 0.0 on pci0
agp0: allocating GATT for aperture of size 256M
pcib2: <VIA 82C598MVP (Apollo MVP3) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib2
isab0: <VIA 82C586 PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 82C586 ATA33 controller> port 0xd000-0xd00f at device 7.1 on pci0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0xd000
ata0: mask=03 ostat0=50 ostat2=00
ata0-master: ATAPI 00 00
ata0-slave: ATAPI 00 00
ata0: mask=03 stat0=50 stat1=00
ata0-master: ATA 01 a5
ata0: devices=01
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0xd008
ata1: mask=03 ostat0=50 ostat2=00
ata1-master: ATAPI 00 00
ata1-slave: ATAPI 00 00
ata1: mask=03 stat0=50 stat1=00
ata1-master: ATA 01 a5
ata1: devices=01
ata1: at 0x170 irq 15 on atapci0
uhci0: <VIA 83C572 USB controller> port 0xd400-0xd41f irq 11 at device 7.2 on pc
i0
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <unknown card> (vendor=0x1106, dev=0x3040) at 7.3
fxp0: <Intel 82559 Pro/100 Ethernet> port 0xd800-0xd83f mem 0xd6000000-0xd60ffff
f,0xd6100000-0xd6100fff irq 10 at device 15.0 on pci0
fxp0: using memory space register mapping
fxp0: Ethernet address 00:04:ac:e5:d3:59
fxp0: PCI IDs: 8086 1229 1014 305c 0008
fxp0: Dynamic Standby mode is disabled
inphy0: <i82555 10/100 media interface> on miibus0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: fxp0 attached
pci0: <ATI Mach64-GT graphics accelerator> (vendor=0x1002, dev=0x4754) at 16.0
ahc0: <Adaptec 2940 Ultra SCSI adapter> port 0xe000-0xe0ff mem 0xd6101000-0xd610
1fff irq 5 at device 19.0 on pci0
ahc0: Defaulting to MEMIO off
ahc0: Reading SEEPROM...done.
ahc0: internal 50 cable not present, internal 68 cable is present
ahc0: external cable not present
ahc0: BIOS eeprom is present
ahc0: High byte termination Enabled
ahc0: Low byte termination Enabled
ahc0: Downloading Sequencer Program... 440 instructions downloaded
ahc0: Features 0x5, Bugs 0x11, Flags 0x20485540
aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs
pci-: pci1 exists, using next available unit number
pcib1: <Host to PCI bridge> on motherboard
pci2: <PCI bus> on pcib1
ex_isa_identify()
ata-: ata0 exists, using next available unit number
ata-: ata1 exists, using next available unit number
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xcbfff,0xcc000-0xcd7ff,0xc
e000-0xd3fff on isa0
pmtimer0 on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ata2 failed to probe at port 0x1f0 irq 14 on isa0
ata3 failed to probe at port 0x170 irq 15 on isa0
adv0 failed to probe on isa0
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x330
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x334
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x230
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x234
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x130
bt0: Failed Status Reg Test - ff
bt_isa_probe: Probe failed at 0x134
bt0 failed to probe at port 0x134-0x137 on isa0
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0: status reg test failed ff
aha0 failed to probe at port 0x134-0x137 on isa0
aic0 failed to probe at port 0x140-0x15f on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x1d0000
psm0: current command byte:0047
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
psm: status 00 02 64
psm: status 1a 03 3c
psm: status 1a 03 3c
psm: status 1a 03 3c
psm: data c8 c6 51
psm: data 08 00 00
psm: status 00 02 64
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model MouseMan+, device ID 0-51, 3 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:08, syncbits:08
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0e 0f 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
sio0: irq maps: 0x41 0x51 0x41 0x41
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1: irq maps: 0x41 0x49 0x41 0x41
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio2: not probed (disabled)
sio3: not probed (disabled)
ppc0: parallel port found at 0x378
ppc0: using extended I/O port range
ppc0: EPP SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
ppi0: <Parallel I/O> on ppbus0
plip0: <PLIP network interface> on ppbus0
bpf: lp0 attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
lnc0: not probed (disabled)
cs0: not probed (disabled)
sn0: not probed (disabled)
isa_probe_children: probing PnP devices
BIOS Geometries:
0:03fffe3f 0..1023=1024 cylinders, 0..254=255 heads, 1..63=63 sectors
1:0345773f 0..837=838 cylinders, 0..119=120 heads, 1..63=63 sectors
2:0223fe3f 0..547=548 cylinders, 0..254=255 heads, 1..63=63 sectors
3:0223fe3f 0..547=548 cylinders, 0..254=255 heads, 1..63=63 sectors
4:0223fe3f 0..547=548 cylinders, 0..254=255 heads, 1..63=63 sectors
5:0223fe3f 0..547=548 cylinders, 0..254=255 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
bpf: lo0 attached
bpf: ppp0 attached
new masks: bio 68c840, tty 63109a, net 67149a
bpf: sl0 attached
bpf: faith0 attached
ad0: success setting UDMA2 on VIA chip
Creating DISK ad0
ar: FreeBSD check1 failed
ad0: <FUJITSU MPE3084AE/EE-C0-23> ATA-4 disk at ata0-master
ad0: 8063MB (16514064 sectors), 16383 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA33
ad0: piomode=4 dmamode=2 udmamode=4 cblid=1
ad2: success setting UDMA2 on VIA chip
Creating DISK ad2
ar: FreeBSD check1 failed
ad2: <FUJITSU MPC3032AT/6021> ATA-3 disk at ata1-master
ad2: 3093MB (6335280 sectors), 6704 C, 15 H, 63 S, 512 B
ad2: 16 secs/int, 1 depth queue, UDMA33
ad2: piomode=4 dmamode=2 udmamode=2 cblid=0
Waiting 15 seconds for SCSI devices to settle
(noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
(ahc0:A:0:0): Received WDTR 1 filtered to 0
(ahc0:A:0:0): Target Initiated WDTR
(ahc0:A:0:0): Sending WDTR 0
ahc0: target 0 using 8bit transfers
(ahc0:A:0:0): Received SDTR period 19, offset 1e
Filtered to period 0, offset 0
ahc0: target 0 using asynchronous transfers
(ahc0:A:0:0): Target Initiated SDTR
(ahc0:A:0:0): Sending SDTR period 45, offset 0
(ahc0:A:1:0): Received WDTR 1 filtered to 0
(ahc0:A:1:0): Target Initiated WDTR
(ahc0:A:1:0): Sending WDTR 0
ahc0: target 1 using 8bit transfers
(ahc0:A:1:0): Received SDTR period 19, offset 1e
Filtered to period 0, offset 0
ahc0: target 1 using asynchronous transfers
(ahc0:A:1:0): Target Initiated SDTR
(ahc0:A:1:0): Sending SDTR period 45, offset 0
(ahc0:A:2:0): Received WDTR 1 filtered to 0
(ahc0:A:2:0): Target Initiated WDTR
(ahc0:A:2:0): Sending WDTR 0
ahc0: target 2 using 8bit transfers
(ahc0:A:2:0): Received SDTR period 19, offset 1e
Filtered to period 0, offset 0
ahc0: target 2 using asynchronous transfers
(ahc0:A:2:0): Target Initiated SDTR
(ahc0:A:2:0): Sending SDTR period 45, offset 0
(ahc0:A:3:0): Received WDTR 1 filtered to 0
(ahc0:A:3:0): Target Initiated WDTR
(ahc0:A:3:0): Sending WDTR 0
ahc0: target 3 using 8bit transfers
(ahc0:A:3:0): Received SDTR period 19, offset 1e
Filtered to period 0, offset 0
ahc0: target 3 using asynchronous transfers
(ahc0:A:3:0): Target Initiated SDTR
(ahc0:A:3:0): Sending SDTR period 45, offset 0
(ahc0:A:0:0): Sending WDTR 1
(ahc0:A:0:0): Received WDTR 1 filtered to 1
ahc0: target 0 using 16bit transfers
(ahc0:A:0:0): Sending SDTR period c, offset 8
(ahc0:A:0:0): Received SDTR period 19, offset 8
Filtered to period 19, offset 8
ahc0: target 0 synchronous at 10.0MHz, offset = 0x8
(ahc0:A:1:0): Sending WDTR 1
(ahc0:A:1:0): Received WDTR 1 filtered to 1
ahc0: target 1 using 16bit transfers
(ahc0:A:1:0): Sending SDTR period c, offset 8
(ahc0:A:1:0): Received SDTR period 19, offset 8
Filtered to period 19, offset 8
ahc0: target 1 synchronous at 10.0MHz, offset = 0x8
(ahc0:A:2:0): Sending WDTR 1
(ahc0:A:2:0): Received WDTR 1 filtered to 1
ahc0: target 2 using 16bit transfers
(ahc0:A:2:0): Sending SDTR period c, offset 8
(ahc0:A:2:0): Received SDTR period 19, offset 8
Filtered to period 19, offset 8
ahc0: target 2 synchronous at 10.0MHz, offset = 0x8
(ahc0:A:3:0): Sending WDTR 1
(ahc0:A:3:0): Received WDTR 1 filtered to 1
ahc0: target 3 using 16bit transfers
(ahc0:A:3:0): Sending SDTR period c, offset 8
(ahc0:A:3:0): Received SDTR period 19, offset 8
Filtered to period 19, offset 8
ahc0: target 3 synchronous at 10.0MHz, offset = 0x8
Creating DISK da0
Creating DISK da1
Creating DISK da2
Creating DISK da3
pass0 at ahc0 bus 0 target 0 lun 0
pass0: <IBM DFHSS4W 4D4D> Fixed Direct Access SCSI-2 device
pass0: Serial Number 00160467
pass0: 20.000MB/s transfers (10.000MHz, offset 8, 16bit), Tagged Queueing Enable
d
pass1 at ahc0 bus 0 target 1 lun 0
pass1: <IBM DFHSS4W 4D4D> Fixed Direct Access SCSI-2 device
pass1: Serial Number 00158136
pass1: 20.000MB/s transfers (10.000MHz, offset 8, 16bit), Tagged Queueing Enable
d
pass2 at ahc0 bus 0 target 2 lun 0
pass2: <IBM DFHSS4W 4D4D> Fixed Direct Access SCSI-2 device
pass2: Serial Number 00157018
pass2: 20.000MB/s transfers (10.000MHz, offset 8, 16bit), Tagged Queueing Enable
d
pass3 at ahc0 bus 0 target 3 lun 0
pass3: <IBM DFHSS4W 4D4D> Fixed Direct Access SCSI-2 device
pass3: Serial Number 00154314
pass3: 20.000MB/s transfers (10.000MHz, offset 8, 16bit), Tagged Queueing Enable
d
da0 at ahc0 bus 0 target 0 lun 0
da0: <IBM DFHSS4W 4D4D> Fixed Direct Access SCSI-2 device
da0: Serial Number 00160467
da0: 20.000MB/s transfers (10.000MHz, offset 8, 16bit), Tagged Queueing Enabled
da0: 4303MB (8813870 512 byte sectors: 255H 63S/T 548C)
da3 at ahc0 bus 0 target 3 lun 0
da3: <IBM DFHSS4W 4D4D> Fixed Direct Access SCSI-2 device
da3: Serial Number 00154314
da3: 20.000MB/s transfers (10.000MHz, offset 8, 16bit), Tagged Queueing Enabled
da3: 4303MB (8813870 512 byte sectors: 255H 63S/T 548C)
da2 at ahc0 bus 0 target 2 lun 0
da2: <IBM DFHSS4W 4D4D> Fixed Direct Access SCSI-2 device
da2: Serial Number 00157018
da2: 20.000MB/s transfers (10.000MHz, offset 8, 16bit), Tagged Queueing Enabled
da2: 4303MB (8813870 512 byte sectors: 255H 63S/T 548C)
da1 at ahc0 bus 0 target 1 lun 0
da1: <IBM DFHSS4W 4D4D> Fixed Direct Access SCSI-2 device
da1: Serial Number 00158136
da1: 20.000MB/s transfers (10.000MHz, offset 8, 16bit), Tagged Queueing Enabled
da1: 4303MB (8813870 512 byte sectors: 255H 63S/T 548C)
Mounting root from ufs:/dev/ad0s1a
ad0s1: type 0xa5, start 63, end = 16498754, size 16498692 : OK
start_init: trying /sbin/init
dumpon: crash dumps to /dev/ad0s1b (116, 131073)
swapon: adding /dev/ad0s1b as swap device
Automatic boot in progress...
/dev/ad0s1a: FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/ad0s1a: clean, 46795 free (715 frags, 5760 blocks, 1.1% fragmentation)
da2s1: type 0xa5, start 63, end = 8803619, size 8803557 : OK
da1s1: type 0xa5, start 63, end = 8803619, size 8803557 : OK
da0s1: type 0xa5, start 63, end = 8803619, size 8803557 : OK
da3s1: type 0xa5, start 63, end = 8803619, size 8803557 : OK
/dev/ad0s1e: aFILESYSTEM CLEANd; SKIPPING CHECK2S
s/dev/ad0s1e: 1clean, 128440 fr:ee type 0xa5, start 63, end = 6335279, size 633
5217 : OK
(64 frags, 16047 blocks, 0.0% fragmentation)
/dev/da1s1e: FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/da1s1e: clean, 2140805 free (61 frags, 267593 blocks, 0.0% fragmentation)
/dev/ad2s1e: FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/ad2s1e: clean, 1523698 free /dev/da0s1e: FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/da0s1e: clean, 2140989 free (117 frags, 267609 blocks, 0.0% fragmentation)
(82 frags, 190452 blocks, 0.0% fragmentation)
/dev/da2s1e: FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/da2s1e: clean, 2142357 free (77 frags, 267785 blocks, 0.0% fragmentation)
/dev/ad0s1f: FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/ad0s1f: clean, 128997 free (13 frags, 16123 blocks, 0.0% fragmentation)
/dev/da3s1e: FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/da3s1e: clean, 2138589 free (93 frags, 267312 blocks, 0.0% fragmentation)
/dev/ad0s1g: FILESYSTEM CLEAN; SKIPPING CHECKS
/dev/ad0s1g: clean, 2788411 free (52483 frags, 341991 blocks, 1.5% fragmentation
)
Doing initial network setup: hostname.
fxp0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
inet6 fe80::204:acff:fee5:d359%fxp0 prefixlen 64 scopeid 0x1
inet 192.168.3.56 netmask 0xffffff00 broadcast 192.168.3.255
ether 00:04:ac:e5:d3:59
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3
inet 127.0.0.1 netmask 0xff000000
IP packet filtering initialized, divert disabled, rule-based forwarding enabled,
default to deny, logging disabled
Kernel firewall module loaded
Flushed all rules.
00100 allow ip from any to any via lo0
00200 deny ip from any to 127.0.0.0/8
00300 deny ip from 127.0.0.0/8 to any
65000 allow ip from any to any
Firewall rules loaded, starting divert daemons:.
Additional routing options: TCP keepalive=YES.
Routing daemons:.
Clearing /tmp:.
Additional daemons: syslogdad0: WRITE command timeout tag=0 serv=0 - resetting
ata0: resetting devices .. ata0: mask=03 ostat0=58 ostat2=00
ad0: ATAPI 00 00
ata0-slave: ATAPI 00 00
ata0: mask=03 stat0=50 stat1=00
ad0: ATA 01 a5
ata0: devices=01
ad0: success setting UDMA2 on VIA chip
done
.
Checking for core dump: savecore: reboot after panic: general protection fault
Feb 23 22:24:07 raider savecore: reboot after panic: general protection fault
savecore: system went down at Mon Feb 23 22:07:26 2004
savecore: writing core to /var/crash/vmcore.5
ad0: WRITE command timeout tag=0 serv=0 - resetting
ata0: resetting devices .. ata0: mask=03 ostat0=58 ostat2=00
ad0: ATAPI 00 00
ata0-slave: ATAPI 00 00
ata0: mask=03 stat0=50 stat1=00
ad0: ATA 01 a5
ata0: devices=01
ad0: success setting UDMA2 on VIA chip
done
ad0: WRITE command timeout tag=0 serv=0 - resetting
ata0: resetting devices .. ata0: mask=03 ostat0=58 ostat2=00
ad0: ATAPI 00 00
ata0-slave: ATAPI 00 00
ata0: mask=03 stat0=50 stat1=00
ad0: ATA 01 a5
ata0: devices=01
ad0: success setting UDMA2 on VIA chip
done
savecore: writing kernel to /var/crash/kernel.5
ad0: WRITE command timeout tag=0 serv=0 - resetting
ata0: resetting devices .. ata0: mask=03 ostat0=58 ostat2=00
ad0: ATAPI 00 00
ata0-slave: ATAPI 00 00
ata0: mask=03 stat0=50 stat1=00
ad0: ATA 01 a5
ata0: devices=01
ad0: success setting UDMA2 on VIA chip
done
ad0: WRITE command timeout tag=0 serv=0 - resetting
ata0: resetting devices .. ata0: mask=03 ostat0=58 ostat2=00
ad0: ATAPI 00 00
ata0-slave: ATAPI 00 00
ata0: mask=03 stat0=50 stat1=00
ad0: ATA 01 a5
ata0: devices=01
ad0: success setting UDMA2 on VIA chip
done
ad0: WRITE command timeout tag=0 serv=0 - resetting
ata0: resetting devices .. ata0: mask=03 ostat0=58 ostat2=00
ad0: ATAPI 00 00
ata0-slave: ATAPI 00 00
ata0: mask=03 stat0=50 stat1=00
ad0: ATA 01 a5
ata0: devices=01
ad0: success setting UDMA2 on VIA chip
done
Doing additional network setup: ntpdate ntpd.
Starting final network daemons: nfsiod NFS access cache time=2.
ELF ldconfig path: /usr/lib /usr/lib/compat /usr/local/lib
a.out ldconfig path: /usr/lib/aout /usr/lib/compat/aout
Starting standard daemons: cron sshd.
Initial rc.i386 initialization: apm.
entropy IRQs: 1 3 4 5 6 10 14 15.
Configuring syscons: blanktime screensaver.
Additional ABI support:.
Local package initialization:.
Additional TCP options:.
Mon Feb 23 22:25:14 EST 2004
FreeBSD/i386 (raider.home.local) (ttyd0)
login:
More information about the freebsd-hardware
mailing list