dual ( HP ProLiant ML350 ) kernel config ?
Guillermo Bautista
gbautista at odmcomputers.com
Fri Feb 13 01:04:50 PST 2004
I configured two of that same machines and installed FreeBSD 4.9 and
FreeBSD 5.1 respectively (the performance of 5.1 is better).
I managed to recompile for SMP (dual processor) without any problem.
Remember to configure in your BIOS the nmb_table (or something like that)
as for a "linux system".
This is my SMP kernel configuration file for the 4.9 version, if it's useful
for you:
--------
machine i386
cpu I686_CPU
ident SMP
maxusers 0
#makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols
options MATH_EMULATE #Support for x87 emulation
options INET #InterNETworking
options INET6 #IPv6 communications protocols
options FFS #Berkeley Fast Filesystem
options FFS_ROOT #FFS usable as root device [keep this!]
options SOFTUPDATES #Enable FFS soft updates support
options UFS_DIRHASH #Improve performance on big directories
options MFS #Memory Filesystem
options MD_ROOT #MD is a potential root device
options NFS #Network Filesystem
options NFS_ROOT #NFS usable as root device, NFS required
options MSDOSFS #MSDOS Filesystem
options CD9660 #ISO 9660 Filesystem
options CD9660_ROOT #CD-ROM usable as root, CD9660 required
options PROCFS #Process filesystem
options COMPAT_43 #Compatible with BSD 4.3 [KEEP THIS!]
options SCSI_DELAY=15000 #Delay (in ms) before probing SCSI
options UCONSOLE #Allow users to grab the console
options USERCONFIG #boot -c editor
options VISUAL_USERCONFIG #visual boot -c editor
options KTRACE #ktrace(1) support
options SYSVSHM #SYSV-style shared memory
options SYSVMSG #SYSV-style message queues
options SYSVSEM #SYSV-style semaphores
options P1003_1B #Posix P1003_1B real-time extensions
options _KPOSIX_PRIORITY_SCHEDULING
options ICMP_BANDLIM #Rate limit bad replies
options KBD_INSTALL_CDEV # install a CDEV entry in /dev
options AHC_REG_PRETTY_PRINT # Print register bitfields in debug
# output. Adds ~128k to driver.
options AHD_REG_PRETTY_PRINT # Print register bitfields in debug
# output. Adds ~215k to driver.
# To make an SMP kernel, the next two are needed
options SMP # Symmetric MultiProcessor Kernel
options APIC_IO # Symmetric (APIC) I/O
# To support HyperThreading, HTT is needed in addition to SMP and APIC_IO
#options HTT # HyperThreading Technology
device isa
device eisa
device pci
# Floppy drives
device fdc0 at isa? port IO_FD1 irq 6 drq 2
device fd0 at fdc0 drive 0
device fd1 at fdc0 drive 1
#
# If you have a Toshiba Libretto with its Y-E Data PCMCIA floppy,
# don't use the above line for fdc0 but the following one:
#device fdc0
# ATA and ATAPI devices
device ata0 at isa? port IO_WD1 irq 14
device ata1 at isa? port IO_WD2 irq 15
device ata
device atadisk # ATA disk drives
device atapicd # ATAPI CDROM drives
device atapifd # ATAPI floppy drives
device atapist # ATAPI tape drives
options ATA_STATIC_ID #Static device numbering
# SCSI Controllers
#device ahb # EISA AHA1742 family
#device ahc # AHA2940 and onboard AIC7xxx devices
#device ahd # AHA39320/29320 and onboard AIC79xx devices
#device amd # AMD 53C974 (Tekram DC-390(T))
#device isp # Qlogic family
#device mpt # LSI-Logic MPT/Fusion
#device ncr # NCR/Symbios Logic
#device sym # NCR/Symbios Logic (newer chipsets)
options SYM_SETUP_LP_PROBE_MAP=0x40
# Allow ncr to attach legacy NCR devices when
# both sym and ncr are configured
device adv0 at isa?
device adw
device bt0 at isa?
device aha0 at isa?
device aic0 at isa?
device ncv # NCR 53C500
device nsp # Workbit Ninja SCSI-3
device stg # TMC 18C30/18C50
# SCSI peripherals
device scbus # SCSI bus (required)
device da # Direct Access (disks)
device sa # Sequential Access (tape etc)
device cd # CD
device pass # Passthrough device (direct SCSI access)
# RAID controllers interfaced to the SCSI subsystem
#device asr # DPT SmartRAID V, VI and Adaptec SCSI RAID
#device dpt # DPT Smartcache - See LINT for options!
#device iir # Intel Integrated RAID
#device mly # Mylex AcceleRAID/eXtremeRAID
device ciss # Compaq SmartRAID 5* series
# RAID controllers
#device aac # Adaptec FSA RAID, Dell PERC2/PERC3
#device aacp # SCSI passthrough for aac (requires CAM)
device ida # Compaq Smart RAID
#device amr # AMI MegaRAID
#device mlx # Mylex DAC960 family
#device twe # 3ware Escalade
# atkbdc0 controls both the keyboard and the PS/2 mouse
device atkbdc0 at isa? port IO_KBD
device atkbd0 at atkbdc? irq 1 flags 0x1
device psm0 at atkbdc? irq 12
device vga0 at isa?
# splash screen/screen saver
pseudo-device splash
# syscons is the default console driver, resembling an SCO console
device sc0 at isa? flags 0x100
# Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver
#device vt0 at isa?
#options XSERVER # support for X server on a vt console
#options FAT_CURSOR # start with block cursor
# If you have a ThinkPAD, uncomment this along with the rest of the PCVT
lines
#options PCVT_SCANSET=2 # IBM keyboards are non-std
device agp # support several AGP chipsets
# Floating point support - do not disable.
device npx0 at nexus? port IO_NPX irq 13
# Power management support (see LINT for more options)
device apm0 at nexus? disable flags 0x20 # Advanced Power Management
# PCCARD (PCMCIA) support
device card
device pcic0 at isa? irq 0 port 0x3e0 iomem 0xd0000
device pcic1 at isa? irq 0 port 0x3e2 iomem 0xd4000 disable
# Serial (COM) ports
device sio0 at isa? port IO_COM1 flags 0x10 irq 4
device sio1 at isa? port IO_COM2 irq 3
device sio2 at isa? disable port IO_COM3 irq 5
device sio3 at isa? disable port IO_COM4 irq 9
# Parallel port
device ppc0 at isa? irq 7
device ppbus # Parallel port bus (required)
device lpt # Printer
device plip # TCP/IP over parallel
device ppi # Parallel port interface device
#device vpo # Requires scbus and da
# PCI Ethernet NICs.
device de # DEC/Intel DC21x4x (``Tulip'')
device em # Intel PRO/1000 adapter Gigabit Ethernet Card (``Wiseman'')
device txp # 3Com 3cR990 (``Typhoon'')
device vx # 3Com 3c590, 3c595 (``Vortex'')
# PCI Ethernet NICs that use the common MII bus controller code.
# NOTE: Be sure to keep the 'device miibus' line in order to use these NICs!
device miibus # MII bus support
device dc # DEC/Intel 21143 and various workalikes
device fxp # Intel EtherExpress PRO/100B (82557, 82558)
device pcn # AMD Am79C97x PCI 10/100 NICs
device rl # RealTek 8129/8139
device sf # Adaptec AIC-6915 (``Starfire'')
device sis # Silicon Integrated Systems SiS 900/SiS 7016
device ste # Sundance ST201 (D-Link DFE-550TX)
device tl # Texas Instruments ThunderLAN
device tx # SMC EtherPower II (83c170 ``EPIC'')
device vr # VIA Rhine, Rhine II
device wb # Winbond W89C840F
device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'')
device bge # Broadcom BCM570x (``Tigon III'')
# ISA Ethernet NICs.
# 'device ed' requires 'device miibus'
device ed0 at isa? disable port 0x280 irq 10 iomem 0xd8000
device ex
device ep
device fe0 at isa? disable port 0x300
# Xircom Ethernet
device xe
# PRISM I IEEE 802.11b wireless NIC.
device awi
# WaveLAN/IEEE 802.11 wireless NICs. Note: the WaveLAN/IEEE really
# exists only as a PCMCIA device, so there is no ISA attachment needed
# and resources will always be dynamically assigned by the pccard code.
device wi
# Aironet 4500/4800 802.11 wireless NICs. Note: the declaration below will
# work for PCMCIA and PCI cards, as well as ISA cards set to ISA PnP
# mode (the factory default). If you set the switches on your ISA
# card for a manually chosen I/O address and IRQ, you must specify
# those parameters here.
device an
# The probe order of these is presently determined by i386/isa/isa_compat.c.
device ie0 at isa? disable port 0x300 irq 10 iomem 0xd0000
#device le0 at isa? disable port 0x300 irq 5 iomem 0xd0000
device lnc0 at isa? disable port 0x280 irq 10 drq 0
device cs0 at isa? disable port 0x300
device sn0 at isa? disable port 0x300 irq 10
# Pseudo devices - the number indicates how many units to allocate.
pseudo-device loop # Network loopback
pseudo-device ether # Ethernet support
pseudo-device sl 1 # Kernel SLIP
pseudo-device ppp 1 # Kernel PPP
pseudo-device tun # Packet tunnel.
pseudo-device pty # Pseudo-ttys (telnet etc)
pseudo-device md # Memory "disks"
pseudo-device gif # IPv6 and IPv4 tunneling
pseudo-device faith 1 # IPv6-to-IPv4 relaying (translation)
# The `bpf' pseudo-device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
pseudo-device bpf #Berkeley packet filter
# USB support
device uhci # UHCI PCI->USB interface
device ohci # OHCI PCI->USB interface
device usb # USB Bus (required)
device ugen # Generic
device uhid # "Human Interface Devices"
device ukbd # Keyboard
device ulpt # Printer
device umass # Disks/Mass storage - Requires scbus and da
device ums # Mouse
device uscanner # Scanners
device urio # Diamond Rio MP3 Player
# USB Ethernet, requires mii
device aue # ADMtek USB ethernet
device cue # CATC USB ethernet
device kue # Kawasaki LSI USB ethernet
# FireWire support
device firewire # FireWire bus code
device sbp # SCSI over FireWire (Requires scbus and da)
device fwe # Ethernet over FireWire (non-standard!)
------------------
I hope this helps you.
Guillermo BT
gbautista at odmcomputers.com
-----Mensaje original-----
De: owner-freebsd-hardware at freebsd.org
[mailto:owner-freebsd-hardware at freebsd.org]En nombre de Nelis Lamprecht
Enviado el: martes, 10 de febrero de 2004 8:00
Para: freebsd-hardware at freebsd.org
Asunto: dual ( HP ProLiant ML350 ) kernel config ?
Hi,
I am trying to build a SMP kernel on our new dual Xeon 2.8ghz HP server.
Although I've been using FreeBSD for many years this is my first SMP
machine and I'm not having any luck.
I can't recall the exact error but the machine boots up and then throws
out a bunch of errors relating to IOAPIC programming before it freezes.
Please could someone take a look at my very basic kernel config to see
if there is anything that I have left out that may be causing the
problem. I've pasted dmesg also so you can see the hardware probe.
Thank you kindly.
#########################kernel config#########################
machine i386
cpu I686_CPU
ident GUARDIAN
maxusers 0
options INET #InterNETworking
options FFS #Berkeley Fast Filesystem
options FFS_ROOT #FFS usable as root device [keep
this!]
options SOFTUPDATES #Enable FFS soft updates support
options UFS_DIRHASH #Improve performance on big
directories
options MFS #Memory Filesystem
options MD_ROOT #MD is a potential root device
options NFS #Network Filesystem
options NFS_ROOT #NFS usable as root device, NFS
required
options MSDOSFS #MSDOS Filesystem
options CD9660 #ISO 9660 Filesystem
options CD9660_ROOT #CD-ROM usable as root, CD9660
required
options PROCFS #Process filesystem
options COMPAT_43 #Compatible with BSD 4.3 [KEEP
THIS!]
options SCSI_DELAY=5000 #Delay (in ms) before probing
SCSI
options UCONSOLE #Allow users to grab the console
options USER_LDT #allow user-level control of
i386 ldt
options USERCONFIG #boot -c editor
options VISUAL_USERCONFIG #visual boot -c editor
options KTRACE #ktrace(1) support
options SYSVSHM #SYSV-style shared memory
options SYSVMSG #SYSV-style message queues
options SYSVSEM #SYSV-style semaphores
options P1003_1B #Posix P1003_1B real-time
extensions
options _KPOSIX_PRIORITY_SCHEDULING
options ICMP_BANDLIM #Rate limit bad replies
options KBD_INSTALL_CDEV # install a CDEV entry in /dev
options AHC_REG_PRETTY_PRINT # Print register bitfields in
debug
# Firewall support.
#options IPFILTER
#options IPFILTER_LOG
#options IPFILTER_DEFAULT_BLOCK
# To make an SMP kernel, the next two are needed
options SMP # Symmetric MultiProcessor
Kernel
options APIC_IO # Symmetric (APIC) I/O
device isa
device pci
# Floppy drives
device fdc0 at isa? port IO_FD1 irq 6 drq 2
device fd0 at fdc0 drive 0
device fd1 at fdc0 drive 1
# ATA and ATAPI devices
device ata
device atadisk # ATA disk drives
device atapicd # ATAPI CDROM drives
device atapifd # ATAPI floppy drives
device atapist # ATAPI tape drives
options ATA_STATIC_ID #Static device numbering
# SCSI Controllers
device ahc # AHA2940 and onboard AIC7xxx devices
# SCSI peripherals
device scbus # SCSI bus (required)
device da # Direct Access (disks)
device sa # Sequential Access (tape etc)
device pass # Passthrough device (direct SCSI
access)
# RAID controllers interfaced to the SCSI subsystem
device ciss # Compaq SmartRAID 5* series
# atkbdc0 controls both the keyboard and the PS/2 mouse
device atkbdc0 at isa? port IO_KBD
device atkbd0 at atkbdc? irq 1 flags 0x1
device psm0 at atkbdc? irq 12
device vga0 at isa?
# syscons is the default console driver, resembling an SCO console
device sc0 at isa? flags 0x100
# Floating point support - do not disable.
device npx0 at nexus? port IO_NPX irq 13
# Power management support (see LINT for more options)
#device apm0 at nexus? disable flags 0x20 # Advanced Power
Management
# Serial (COM) ports
device sio0 at isa? port IO_COM1 flags 0x10 irq 4
device sio1 at isa? port IO_COM2 irq 3
#device sio2 at isa? disable port IO_COM3 irq 5
#device sio3 at isa? disable port IO_COM4 irq 9
# Parallel port
device ppc0 at isa? irq 7
device ppbus # Parallel port bus (required)
device lpt # Printer
device plip # TCP/IP over parallel
device ppi # Parallel port interface device
# PCI Ethernet NICs that use the common MII bus controller code.
# NOTE: Be sure to keep the 'device miibus' line in order to use these
NICs!
device miibus # MII bus support
device bge # Broadcom BCM570x (``Tigon III'')
# Pseudo devices - the number indicates how many units to allocate.
pseudo-device loop # Network loopback
pseudo-device ether # Ethernet support
pseudo-device sl 1 # Kernel SLIP
pseudo-device ppp 1 # Kernel PPP
pseudo-device tun # Packet tunnel.
pseudo-device pty # Pseudo-ttys (telnet etc)
pseudo-device md # Memory "disks"
pseudo-device gif # IPv6 and IPv4 tunneling
pseudo-device faith 1 # IPv6-to-IPv4 relaying (translation)
# The `bpf' pseudo-device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
pseudo-device bpf #Berkeley packet filter
# USB support
device ohci # OHCI PCI->USB interface
device usb # USB Bus (required)
device ugen # Generic
device uhid # "Human Interface Devices"
device ukbd # Keyboard
device ulpt # Printer
device umass # Disks/Mass storage - Requires scbus
and da
#######################dmesg###########################
FreeBSD 4.9-RELEASE #0: Mon Oct 27 17:51:09 GMT 2003
root at freebsd-stable.sentex.ca:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz
CPU: Intel(R) Xeon(TM) CPU 2.80GHz (2790.73-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf29 Stepping = 9
Features=0xbfebf9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV
,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Hyperthreading: 2 logical CPUs
real memory = 1342152704 (1310696K bytes)
config> di pcic0
config> di bt0
config> di adv0
config> q
avail memory = 1299718144 (1269256K bytes)
Preloaded elf kernel "kernel" at 0xc053f000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc053f09c.
Warning: Pentium 4 CPU: PSE disabled
Pentium Pro MTRR support enabled
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
ahc0: <Adaptec (Compaq OEM) 3960D Ultra160 SCSI adapter> port
0x2400-0x24ff mem 0xf7df0000-0xf7df0fff irq 3 at device 2.0 on pci0
aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
ahc1: <Adaptec (Compaq OEM) 3960D Ultra160 SCSI adapter> port
0x2800-0x28ff mem 0xf7de0000-0xf7de0fff irq 3 at device 2.1 on pci0
aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs
pci0: <ATI Mach64-GR graphics accelerator> at 3.0
bge0: <Broadcom BCM5702 Gigabit Ethernet, ASIC rev. 0x1002> mem
0xf5fe0000-0xf5feffff irq 5 at device 4.0 on pci0
bge0: Ethernet address: 00:0b:cd:cc:79:d5
miibus0: <MII bus> on bge0
brgphy0: <BCM5703 10/100/1000baseTX PHY> on miibus0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
1000baseTX-FDX, auto
pci0: <unknown card> (vendor=0x0e11, dev=0xa0f0) at 5.0 irq 10
isab0: <PCI to ISA bridge (vendor=1166 device=0201)> at device 15.0 on
pci0
isa0: <ISA bus> on isab0
atapci0: <ServerWorks CSB5 ATA100 controller> port
0x2000-0x200f,0-0x3,0-0x7,0x3f4-0x3f7,0x1f0-0x1f7 at device 15.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
ohci0: <OHCI (generic) USB controller> mem 0xf5fc0000-0xf5fc0fff irq 11
at device 15.2 on pci0
usb0: OHCI version 1.0, legacy support
usb0: SMM does not respond, resetting
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
pcib1: <Host to PCI bridge> on motherboard
pci1: <PCI bus> on pcib1
pcib2: <Host to PCI bridge> on motherboard
pci2: <PCI bus> on pcib2
ciss0: <HP Smart Array 641> port 0x3000-0x30ff mem
0xf7e80000-0xf7ebffff,0xf7ef0000-0xf7ef1fff irq 15 at device 1.0 on pci2
pcib3: <Host to PCI bridge> on motherboard
pci3: <PCI bus> on pcib3
pcib4: <ServerWorks host to PCI bridge(unknown chipset)> on motherboard
pci4: <PCI bus> on pcib4
pcib5: <ServerWorks host to PCI bridge(unknown chipset)> on motherboard
pci5: <PCI bus> on pcib5
bge1: <Broadcom BCM5703X Gigabit Ethernet, ASIC rev. 0x1100> mem
0xf7ff0000-0xf7ffffff irq 11 at device 1.0 on pci5
bge1: Ethernet address: 00:08:02:91:3a:fd
miibus1: <MII bus> on bge1
brgphy1: <BCM5703 10/100/1000baseTX PHY> on miibus1
brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
1000baseTX-FDX, auto
eisa0: <EISA bus> on motherboard
mainboard0: <CPQ0729 (System Board)> on eisa0 slot 0
orm0: <Option ROMs> at iomem
0xc0000-0xc7fff,0xc8000-0xcbfff,0xcc000-0xcd7ff,0xcd800-0xcefff,0xee000-0xef
fff on isa0pmtimer0 on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on
isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppi0: <Parallel I/O> on ppbus0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
acd0: CDROM <LTN486S> at ata0-master PIO4
Waiting 15 seconds for SCSI devices to settle
sa0 at ahc1 bus 0 target 6 lun 0
sa0: <COMPAQ SDX-500C 1.35> Removable Sequential Access SCSI-2 device
sa0: 40.000MB/s transfers (20.000MHz, offset 7, 16bit)
da0 at ciss0 bus 0 target 0 lun 0
da0: <COMPAQ RAID 1 VOLUME OK> Fixed Direct Access SCSI-0 device
da0: 135.168MB/s transfers
da0: 69459MB (142253280 512 byte sectors: 255H 32S/T 17433C)
Mounting root from ufs:/dev/da0s1a
--
Nelis Lamprecht
PGP: http://www.8ball.co.za/pgpkey/nelis.asc
"Unix IS user friendly.. It's just selective about who its friends are."
More information about the freebsd-hardware
mailing list