Dell XPS 1530 - Network card issue - Marvell 88E8040
Chris Stromblad
cs at wa-sp.com
Thu Jan 24 02:32:08 PST 2008
Sorry, here is the correct output, now also run as root!
Again I've included the Wireless, because perhaps someone else would
like to have a look at the data to understand why it's not detected. To
my understanding there should be support as I seem to recall that Intel
even put out the drivers themselves, or at least some hardware
specifications.
09:00.0 0200: 11ab:4354 (rev 12)
Subsystem: 1028:022e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f9ffc000 (64-bit, non-prefetchable)
[size=16K]
Region 2: I/O ports at de00 [size=256]
Capabilities: [48] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [5c] Message Signalled Interrupts: Mask-
64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [c0] Express Legacy Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc
0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal-
Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s
L1, Port 0
Link: Latency L0s <256ns, L1 unlimited
Link: ASPM L0s Enabled RCB 128 bytes CommClk+
ExtSynch-
Link: Speed 2.5Gb/s, Width x1
0b:00.0 0280: 8086:4222 (rev 02)
Subsystem: 8086:1021
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at f9eff000 (32-bit, non-prefetchable)
[size=4K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask-
64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [e0] Express Legacy Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc
0, ExtTag-
Device: Latency L0s <512ns, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal-
Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s
L1, Port 0
Link: Latency L0s <128ns, L1 <64us
Link: ASPM L1 Enabled RCB 64 bytes CommClk+
ExtSynch-
Link: Speed 2.5Gb/s, Width x1
On Thu, 2008-01-24 at 18:46 +0900, Pyun YongHyeon wrote:
> On Thu, Jan 24, 2008 at 10:27:31AM +0100, Chris Stromblad wrote:
> > Hi,
> >
> > This is the output from lspci -v:
>
> 'lspci -nvv' is preferred as I have to check device ids.
>
> > 09:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8040
> > PCI-E Fast Ethernet Controller (rev 12)
> > Subsystem: Dell Unknown device 022e
> > Flags: bus master, fast devsel, latency 0, IRQ 16
> > Memory at f9ffc000 (64-bit, non-prefetchable) [size=16K]
> > I/O ports at de00 [size=256]
> > Capabilities: <access denied>
> >
> > 0b:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG
> > Network Connection (rev 02)
> > Subsystem: Intel Corporation Unknown device 1021
> > Flags: bus master, fast devsel, latency 0, IRQ 17
> > Memory at f9eff000 (32-bit, non-prefetchable) [size=4K]
> > Capabilities: <access denied>
> >
> > I included the wireless data as well because I wanted to ask if you know
> > whether or not this has support from ports? It doesn't get detected when
> > booting FreeBSD so I assume that either it needs a binary blob, or that
> > perhaps there are some drivers in ports that can be installed once I
> > have the wired network functioning properly.
> >
>
> Didn't wpi(4) detect your wireless network hardware?
>
> > Once again thank you very much for your help, and if there is anything
> > else I can do or get you, please let me know!
> >
> > - Chris
> >
>
--
Chris Stromblad
Security Engineer
WASP UK
Regent Street
London, WC2
Dir: +44 207 043 5190
More information about the freebsd-hackers
mailing list