kern/120091: [GEOM][geli][gjournal] geli does not prompt for password on /dev/concat/XXX.eli.journal

[Yoshihiro Ota]

The following reply was made to PR kern/120091; it has been noted by GNATS.

From: Yoshihiro Ota <ota at j.email.ne.jp>
To: Volker <volker at vwsoft.com>
Cc: bug-followup at FreeBSD.org
Subject: Re: kern/120091: [GEOM][geli][gjournal] geli does not prompt for
 password on /dev/concat/XXX.eli.journal
Date: Wed, 30 Jan 2008 05:04:35 -0500

 On Wed, 30 Jan 2008 00:16:58 +0100
 Volker <volker at vwsoft.com> wrote:
 
 > Hi Ota,
 > 
 > Please provide output of:
 > 
 > geli status
 > gconcat status
 > dmesg
 > 
 > Volker
 > 
 
 Please note that the system fails to mount /dev/concat/export.eli.gjournal
 and falls back to the single user mode.  Then, I type "geli attach /dev/concat/export"
 and "GEOM_ELI: Device concat/export.eli created." appears.
 
 
 # geli status
              Name  Status  Components
 concat/export.eli     N/A  concat/export
 # gconcat status
          Name  Status  Components
 concat/export      UP  ad4s3f
                        ad4s4f
 # dmesg
 Copyright (c) 1992-2008 The FreeBSD Project.
 Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
 	The Regents of the University of California. All rights reserved.
 FreeBSD is a registered trademark of The FreeBSD Foundation.
 FreeBSD 7.0-RC1 #400: Fri Jan 25 00:00:28 EST 2008
     root at xxx:/usr/obj/usr/src/sys/GENERIC
 Timecounter "i8254" frequency 1193182 Hz quality 0
 CPU: AMD Turion(tm) 64 X2 Mobile Technology TL-58 (1908.70-MHz 686-class CPU)
   Origin = "AuthenticAMD"  Id = 0x60f81  Stepping = 1
   Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
   Features2=0x2001<SSE3,CX16>
   AMD Features=0xea500800<SYSCALL,NX,MMX+,FFXSR,RDTSCP,LM,3DNow!+,3DNow!>
   AMD Features2=0x11f<LAHF,CMP,SVM,ExtAPIC,CR8,Prefetch>
   Cores per package: 2
 real memory  = 1005584384 (959 MB)
 avail memory = 970309632 (925 MB)
 ACPI APIC Table: <HP     	 APIC  >
 FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
  cpu0 (BSP): APIC ID:  0
  cpu1 (AP): APIC ID:  1
 MADT: Forcing active-low polarity and level trigger for SCI
 ioapic0 <Version 1.1> irqs 0-23 on motherboard
 wlan: mac acl policy registered
 kbd1 at kbdmux0
 ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
 hptrr: HPT RocketRAID controller driver v1.1 (Jan 20 2008 00:19:12)
 acpi0: <HPQOEM SLIC-MPC> on motherboard
 acpi0: [ITHREAD]
 acpi0: Power Button (fixed)
 Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
 acpi_ec0: <Embedded Controller: GPE 0x10> port 0x62,0x66 on acpi0
 acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
 Timecounter "HPET" frequency 25000000 Hz quality 900
 cpu0: <ACPI CPU> on acpi0
 powernow0: <PowerNow! K8> on cpu0
 cpu1: <ACPI CPU> on acpi0
 powernow1: <PowerNow! K8> on cpu1
 acpi_button0: <Power Button> on acpi0
 acpi_button1: <Sleep Button> on acpi0
 acpi_acad0: <AC Adapter> on acpi0
 battery0: <ACPI Control Method Battery> on acpi0
 acpi_lid0: <Control Method Lid Switch> on acpi0
 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
 pci_link9: BIOS IRQ 10 for 0.10.INTB is invalid
 pci0: <ACPI PCI bus> on pcib0
 pci0: <memory, RAM> at device 0.0 (no driver attached)
 pci0: <memory, RAM> at device 0.1 (no driver attached)
 pci0: <memory, RAM> at device 0.2 (no driver attached)
 pci0: <memory, RAM> at device 0.3 (no driver attached)
 pci0: <memory, RAM> at device 0.4 (no driver attached)
 pci0: <memory, RAM> at device 0.5 (no driver attached)
 pci0: <memory, RAM> at device 0.6 (no driver attached)
 pci0: <memory, RAM> at device 0.7 (no driver attached)
 pcib1: <ACPI PCI-PCI bridge> at device 2.0 on pci0
 pci1: <ACPI PCI bus> on pcib1
 pcib2: <ACPI PCI-PCI bridge> at device 3.0 on pci0
 pci3: <ACPI PCI bus> on pcib2
 pci3: <network> at device 0.0 (no driver attached)
 vgapci0: <VGA-compatible display> mem 0xb2000000-0xb2ffffff,0xc0000000-0xcfffffff,0xb1000000-0xb1ffffff irq 18 at device 5.0 on pci0
 pci0: <memory, RAM> at device 9.0 (no driver attached)
 isab0: <PCI-ISA bridge> port 0x1d00-0x1d7f at device 10.0 on pci0
 isa0: <ISA bus> on isab0
 pci0: <serial bus, SMBus> at device 10.1 (no driver attached)
 pci0: <processor> at device 10.3 (no driver attached)
 ohci0: <OHCI (generic) USB controller> mem 0xb0004000-0xb0004fff irq 22 at device 11.0 on pci0
 ohci0: [GIANT-LOCKED]
 ohci0: [ITHREAD]
 usb0: OHCI version 1.0, legacy support
 usb0: SMM does not respond, resetting
 usb0: <OHCI (generic) USB controller> on ohci0
 usb0: USB revision 1.0
 uhub0: <nVidia OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
 uhub0: 8 ports with 8 removable, self powered
 ehci0: <EHCI (generic) USB 2.0 controller> mem 0xb0005000-0xb00050ff irq 22 at device 11.1 on pci0
 ehci0: [GIANT-LOCKED]
 ehci0: [ITHREAD]
 usb1: EHCI version 1.0
 usb1: companion controller, 8 ports each: usb0
 usb1: <EHCI (generic) USB 2.0 controller> on ehci0
 usb1: USB revision 2.0
 uhub1: <nVidia EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb1
 uhub1: 8 ports with 8 removable, self powered
 umass0: <vendor 0x04b4 Cypress AT2LP, class 0/0, rev 2.00/2.40, addr 2> on uhub1
 ugen0: <Sonix Technology Co., Ltd. USB 2.0 Camera, class 239/2, rev 2.00/2.10, addr 3> on uhub1
 atapci0: <nVidia nForce MCP51 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x3080-0x308f at device 13.0 on pci0
 ata0: <ATA channel 0> on atapci0
 ata0: [ITHREAD]
 ata1: <ATA channel 1> on atapci0
 ata1: [ITHREAD]
 atapci1: <nVidia nForce MCP51 SATA300 controller> port 0x30c0-0x30c7,0x30b4-0x30b7,0x30b8-0x30bf,0x30b0-0x30b3,0x3090-0x309f irq 23 at device 14.0 on pci0
 atapci1: [ITHREAD]
 ata2: <ATA channel 0> on atapci1
 ata2: [ITHREAD]
 ata3: <ATA channel 1> on atapci1
 ata3: [ITHREAD]
 pcib3: <ACPI PCI-PCI bridge> at device 16.0 on pci0
 pci_link0: BIOS IRQ 11 for 7.5.INTA is invalid
 pci_link1: BIOS IRQ 11 for 7.5.INTB is invalid
 pci7: <ACPI PCI bus> on pcib3
 fwohci0: <1394 Open Host Controller Interface> mem 0xb8000000-0xb80007ff irq 9 at device 5.0 on pci7
 fwohci0: [FILTER]
 fwohci0: OHCI version 1.10 (ROM=0)
 fwohci0: No. of Isochronous channels is 4.
 fwohci0: EUI64 00:24:1b:00:f7:2b:34:00
 fwohci0: Phy 1394a available S400, 1 ports.
 fwohci0: Link S400, max_rec 2048 bytes.
 firewire0: <IEEE1394(FireWire) bus> on fwohci0
 fwe0: <Ethernet over FireWire> on firewire0
 if_fwe0: Fake Ethernet address: 02:24:1b:2b:34:00
 fwe0: Ethernet address: 02:24:1b:2b:34:00
 fwip0: <IP over FireWire> on firewire0
 fwip0: Firewire address: 00:24:1b:00:f7:2b:34:00 @ 0xfffe00000000, S400, maxrec 2048
 sbp0: <SBP-2/SCSI over FireWire> on firewire0
 dcons_crom0: <dcons configuration ROM> on firewire0
 dcons_crom0: bus_addr 0x12c4000
 fwohci0: Initiate bus reset
 fwohci0: BUS reset
 fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
 pci7: <base peripheral> at device 5.1 (no driver attached)
 pci7: <base peripheral> at device 5.2 (no driver attached)
 pci7: <base peripheral> at device 5.3 (no driver attached)
 pci7: <base peripheral> at device 5.4 (no driver attached)
 pci0: <multimedia> at device 16.1 (no driver attached)
 nfe0: <NVIDIA nForce 430 MCP13 Networking Adapter> port 0x30e0-0x30e7 mem 0xb0008000-0xb0008fff irq 20 at device 20.0 on pci0
 miibus0: <MII bus> on nfe0
 rlphy0: <RTL8201L 10/100 media interface> PHY 1 on miibus0
 rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
 nfe0: Ethernet address: 00:1b:24:68:7c:d7
 nfe0: [FILTER]
 acpi_tz0: <Thermal Zone> on acpi0
 atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
 atkbd0: <AT Keyboard> irq 1 on atkbdc0
 kbd0 at atkbd0
 atkbd0: [GIANT-LOCKED]
 atkbd0: [ITHREAD]
 psm0: <PS/2 Mouse> irq 12 on atkbdc0
 psm0: [GIANT-LOCKED]
 psm0: [ITHREAD]
 psm0: model IntelliMouse, device ID 3
 pmtimer0 on isa0
 orm0: <ISA Option ROM> at iomem 0xcf800-0xd0fff pnpid ORM0000 on isa0
 ppc0: parallel port not found.
 sc0: <System console> at flags 0x100 on isa0
 sc0: VGA <16 virtual consoles, flags=0x300>
 sio0: configured irq 4 not in bitmap of probed irqs 0
 sio0: port may not be enabled
 sio0: configured irq 4 not in bitmap of probed irqs 0
 sio0: port may not be enabled
 sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
 sio0: type 8250 or not responding
 sio0: [FILTER]
 sio1: configured irq 3 not in bitmap of probed irqs 0
 sio1: port may not be enabled
 vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
 ums0: <MosArt Optical Mouse, class 0/0, rev 1.10/0.00, addr 2> on uhub0
 ums0: 3 buttons and Z dir.
 Timecounters tick every 1.000 msec
 hptrr: no controller detected.firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
 firewire0: bus manager 0 (me)
 
 acd0: DVDR <TSSTcorpCD/DVDW TS-L632M/0917> at ata0-master PIO4
 ad4: 152627MB <WDC WD1600BEVS-60RST0 04.01G04> at ata2-master SATA150
 GEOM_LABEL: Label for provider ad4s2 is ntfs/HP_RECOVERY.
 GEOM_CONCAT: Device export created (id=3382027346).
 GEOM_CONCAT: Disk ad4s3f attached to export.
 GEOM_JOURNAL: Journal 4240811370: ad4s4e contains data.
 GEOM_CONCAT: Disk ad4s4f attached to export.
 GEOM_CONCAT: Device export activated.
 GEOM_JOURNAL: Journal 4240811370: ad4s4g contains journal.
 GEOM_JOURNAL: Journal ad4s4e clean.
 SMP: AP CPU #1 Launched!
 da0 at umass-sim0 bus 0 target 0 lun 0
 da0: <SAMSUNG SP2514N 0000> Fixed Direct Access SCSI-0 device 
 da0: 40.000MB/s transfers
 da0: 238475MB (488397168 512 byte sectors: 255H 63S/T 30401C)
 Trying to mount root from ufs:/dev/ad4s4a
 cryptosoft0: <software crypto> on motherboard
 GEOM_ELI: Device concat/export.eli created.
 GEOM_ELI: Encryption: AES-CBC 128
 GEOM_ELI:     Crypto: software
 GEOM_JOURNAL: Journal 2182369297: concat/export.eli contains data.
 GEOM_JOURNAL: Journal 2182369297: concat/export.eli contains journal.
 GEOM_JOURNAL: Journal concat/export.eli clean.
 WARNING: TMPFS is considered to be a highly experimental feature in FreeBSD.
 WARNING: TMPFS is considered to be a highly experimental feature in FreeBSD.
 umass0: at uhub1 port 2 (addr 2) disconnected
 (da0:umass-sim0:0:0:0): lost device
 (da0:umass-sim0:0:0:0): removing device entry
 umass0: detached