Western Digital 1TB My Book Studio

[Sean Bruno]

Stephen Bader wrote:
> Still not working. Looks like we're getting the 'reset start' errors 
> again:
>
> fwohci0: BUS reset
> sbp_post_busreset
> fwohci0: node_id=0xc800ffc0, gen=2, CYCLEMASTER mode
> firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
> fwohci0: fw_set_bus_manager: 0->0 (loop=0)
> firewire0: bus manager 0 (me)
> send phy_config root_node=-1 gap_count=5
> fwohci0: start AT DMA status=72
> bus_explore done
> sbp_post_explore (sbp_cold=1)
> sbp_post_explore: EUI:0090a9341b93f349 not attached, state=3.
> target 0 lun 0 found
> target 0 lun 1 found
> sbp_probe_target: detected non sequential access device(77).  skipping
> fwohci0: BUS reset
> sbp_post_busreset
> fwohci0: node_id=0x8800ffc0, gen=3, non CYCLEMASTER mode
> firewire0: 2 nodes, maxhop <= 1, cable IRM = 0 (me)
> fwohci0: fw_set_bus_manager: 0->0 (loop=0)
> firewire0: root node is not cycle master capable
> firewire0: bus manager 0 (me)
> send phy_config root_node=0 gap_count=5
> fwohci0: start AT DMA status=11
> fwohci0: too many cycle lost, no cycle master presents?
> node1: crom unchanged
> fw_explore: node 2, err = 0
> bus_explore done
> sbp_post_explore (sbp_cold=0)
> sbp_post_explore: EUI:0090a9341b93f349 attached
> target 0 lun 0 found
> target 0 lun 1 found
> sbp0:0:0 ordered:1 type:0 EUI:0090a9341b93f349 node:1 speed:3 maxrec:0 
> new!
> sbp0:0:0 'WD' 'My Book' '001025'
> sbp_login: sec = 0 usec = 675467 ticks = 675
> sbp_probe_target: detected non sequential access device(77).  skipping
> sbp0:0:0 LOGIN
> sbp: alloc 2 xfer
> sbp0:0:0 mgm orb: 010d3154
> sbp0:0:0 request timeout(mgm orb:0x010d3154) ... reset start
> sbp0:0:0 sbp_reset_start
> firewire0: split transaction timeout dst=0xffc1 tl=0x7 state=3
> sbp0:0:0 sbp_reset_start failed: resp=60
> fwohci0: BUS reset
> sbp_post_busreset
> fwohci0: node_id=0xc800ffc1, gen=4, CYCLEMASTER mode
> firewire0: 2 nodes, maxhop <= 1, cable IRM = 1 (me)
> fwohci0: fw_set_bus_manager: 1->1 (loop=0)
> firewire0: bus manager 1 (me)
> send phy_config root_node=1 gap_count=5
> fwohci0: start AT DMA status=72
> node0: crom unchanged
> fw_explore: node 2, err = 0
> bus_explore done
> sbp_post_explore (sbp_cold=0)
> sbp_post_explore: EUI:0090a9341b93f349 attached
> target 0 lun 0 found
> target 0 lun 1 found
> sbp0:0:0 ordered:1 type:0 EUI:0090a9341b93f349 node:0 speed:3 maxrec:0 
> new!
> sbp0:0:0 'WD' 'My Book' '001025'
> sbp_login: sec = 0 usec = 682939 ticks = 682
> sbp_probe_target: detected non sequential access device(77).  skipping
> sbp0:0:0 LOGIN
> sbp: alloc 3 xfer
> sbp0:0:0 mgm orb: 010d328c
> sbp0:0:0 request timeout(mgm orb:0x010d328c) ... reset start
> sbp0:0:0 sbp_reset_start
>
> -Steve
>
>
Ok, change the debug level to 2 (firewire_debug and sbp_debug sysctl's) 
and email me the result.  We'll get this eventually!


-- 
Sean Bruno
MiraLink Corporation
6015 NE 80th Ave, Ste 100
Portland, OR 97218
Cell 503-358-6832
Phone 503-621-5143
Fax 503-621-5199
MSN: sbruno at miralink.com
Google:  seanwbruno at gmail.com