smartctl 6.6 2017-11-05 r4594 [FreeBSD 12.0-CURRENT amd64] (local build) Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Red Device Model: WDC WD30EFRX-68EUZN0 Serial Number: Seriennummer LU WWN Device Id: 5 0014ee 0ae56aef0 Firmware Version: 80.00A80 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Sat Dec 23 11:59:30 2017 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Unavailable APM feature is: Unavailable Rd look-ahead is: Enabled Write cache is: Enabled DSN feature is: Unavailable ATA Security is: Disabled, NOT FROZEN [SEC1] Wt Cache Reorder: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (38760) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 389) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x703d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 171 165 021 - 6416 4 Start_Stop_Count -O--CK 099 099 000 - 1860 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 072 072 000 - 20809 10 Spin_Retry_Count -O--CK 100 100 000 - 0 11 Calibration_Retry_Count -O--CK 100 100 000 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 1858 192 Power-Off_Retract_Count -O--CK 200 200 000 - 112 193 Load_Cycle_Count -O--CK 001 001 000 - 1974142 194 Temperature_Celsius -O---K 128 109 000 - 22 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] Address Access R/W Size Description 0x00 GPL,SL R/O 1 Log Directory 0x01 SL R/O 1 Summary SMART error log 0x02 SL R/O 5 Comprehensive SMART error log 0x03 GPL R/O 6 Ext. Comprehensive SMART error log 0x06 SL R/O 1 SMART self-test log 0x07 GPL R/O 1 Extended self-test log 0x09 SL R/W 1 Selective self-test log 0x10 GPL R/O 1 NCQ Command Error log 0x11 GPL R/O 1 SATA Phy Event Counters log 0x21 GPL R/O 1 Write stream error log 0x22 GPL R/O 1 Read stream error log 0x80-0x9f GPL,SL R/W 16 Host vendor specific log 0xa0-0xa7 GPL,SL VS 16 Device vendor specific log 0xa8-0xb7 GPL,SL VS 1 Device vendor specific log 0xbd GPL,SL VS 1 Device vendor specific log 0xc0 GPL,SL VS 1 Device vendor specific log 0xc1 GPL VS 93 Device vendor specific log 0xe0 GPL,SL R/W 1 SCT Command/Status 0xe1 GPL,SL R/W 1 SCT Data Transfer SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 7 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 7 [6] occurred at disk power-on lifetime: 16151 hours (672 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 98 01 cd d0 40 00 Error: IDNF at LBA = 0x9801cdd0 = 2550255056 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 50 00 00 98 01 cd d0 40 08 00:12:14.943 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 40 08 00:12:05.025 FLUSH CACHE EXT 61 00 08 00 40 00 01 5d 50 9f a0 40 08 00:12:05.024 WRITE FPDMA QUEUED 61 00 08 00 38 00 01 5d 50 9d a0 40 08 00:12:05.024 WRITE FPDMA QUEUED 61 00 08 00 30 00 00 00 00 13 a0 40 08 00:12:05.024 WRITE FPDMA QUEUED Error 6 [5] occurred at disk power-on lifetime: 10875 hours (453 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 01 30 01 ce 78 40 00 Error: IDNF at LBA = 0x13001ce78 = 5100392056 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 b0 00 01 30 01 ce 78 40 08 04:06:34.288 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 40 08 04:06:24.234 FLUSH CACHE EXT 61 00 08 00 a0 00 01 5d 50 9f 30 40 08 04:06:24.234 WRITE FPDMA QUEUED 61 00 08 00 98 00 01 5d 50 9d 30 40 08 04:06:24.234 WRITE FPDMA QUEUED 61 00 08 00 90 00 00 00 00 13 30 40 08 04:06:24.233 WRITE FPDMA QUEUED Error 5 [4] occurred at disk power-on lifetime: 8417 hours (350 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 c4 06 ba 08 40 00 Error: IDNF at LBA = 0xc406ba08 = 3288775176 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 a8 00 00 c4 06 ba 08 40 08 00:45:57.190 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 40 08 00:45:47.264 FLUSH CACHE EXT 61 00 08 00 98 00 01 5d 50 9f b0 40 08 00:45:47.263 WRITE FPDMA QUEUED 61 00 08 00 90 00 01 5d 50 9d b0 40 08 00:45:47.263 WRITE FPDMA QUEUED 61 00 08 00 88 00 00 00 00 13 b0 40 08 00:45:47.263 WRITE FPDMA QUEUED Error 4 [3] occurred at disk power-on lifetime: 3423 hours (142 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 b2 59 f6 a8 40 00 Error: IDNF at LBA = 0xb259f6a8 = 2992240296 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 f8 00 00 b2 59 f6 a8 40 08 12:09:22.415 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 40 08 12:09:13.160 FLUSH CACHE EXT 61 00 08 00 f8 00 01 5d 50 9f 90 40 08 12:09:13.159 WRITE FPDMA QUEUED 61 00 08 00 f0 00 01 5d 50 9d 90 40 08 12:09:13.159 WRITE FPDMA QUEUED 61 00 08 00 e8 00 00 00 00 13 90 40 08 12:09:13.159 WRITE FPDMA QUEUED Error 3 [2] occurred at disk power-on lifetime: 2928 hours (122 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 c0 05 10 20 40 00 Error: IDNF at LBA = 0xc0051020 = 3221557280 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 00 00 00 c0 05 10 20 40 08 09:36:05.067 WRITE FPDMA QUEUED 61 00 08 00 00 00 01 5d 50 9f f0 40 08 09:35:50.674 WRITE FPDMA QUEUED 61 00 08 00 f8 00 01 5d 50 9d f0 40 08 09:35:50.674 WRITE FPDMA QUEUED 61 00 08 00 f0 00 00 00 00 13 f0 40 08 09:35:50.674 WRITE FPDMA QUEUED 61 00 08 00 e8 00 00 00 00 11 f0 40 08 09:35:50.674 WRITE FPDMA QUEUED Error 2 [1] occurred at disk power-on lifetime: 1989 hours (82 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 ae 07 ce 30 40 00 Error: IDNF at LBA = 0xae07ce30 = 2919747120 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 78 00 00 ae 07 ce 30 40 08 04:16:19.349 WRITE FPDMA QUEUED 61 00 08 00 78 00 01 5d 50 9f 98 40 08 04:16:05.011 WRITE FPDMA QUEUED 61 00 08 00 70 00 01 5d 50 9d 98 40 08 04:16:05.011 WRITE FPDMA QUEUED 61 00 08 00 68 00 00 00 00 13 98 40 08 04:16:05.011 WRITE FPDMA QUEUED 61 00 08 00 60 00 00 00 00 11 98 40 08 04:16:05.011 WRITE FPDMA QUEUED Error 1 [0] occurred at disk power-on lifetime: 1764 hours (73 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 aa 1a 86 e8 40 00 Error: IDNF at LBA = 0xaa1a86e8 = 2853865192 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 d0 00 00 aa 1a 86 e8 40 08 12:13:30.211 WRITE FPDMA QUEUED 61 00 08 00 d0 00 01 5d 50 9f 30 40 08 12:13:20.248 WRITE FPDMA QUEUED 61 00 08 00 c8 00 01 5d 50 9d 30 40 08 12:13:20.248 WRITE FPDMA QUEUED 61 00 08 00 c0 00 00 00 00 13 30 40 08 12:13:20.248 WRITE FPDMA QUEUED 61 00 08 00 b8 00 00 00 00 11 30 40 08 12:13:20.248 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 18023 - # 2 Short offline Completed without error 00% 2620 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 22 Celsius Power Cycle Min/Max Temperature: 22/22 Celsius Lifetime Min/Max Temperature: 11/41 Celsius Under/Over Temperature Limit Count: 0/0 Vendor specific: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (301) Index Estimated Time Temperature Celsius 302 2017-12-23 04:01 22 *** ... ..( 92 skipped). .. *** 395 2017-12-23 05:34 22 *** 396 2017-12-23 05:35 21 ** ... ..( 93 skipped). .. ** 12 2017-12-23 07:09 21 ** 13 2017-12-23 07:10 22 *** ... ..( 92 skipped). .. *** 106 2017-12-23 08:43 22 *** 107 2017-12-23 08:44 ? - 108 2017-12-23 08:45 21 ** ... ..( 29 skipped). .. ** 138 2017-12-23 09:15 21 ** 139 2017-12-23 09:16 22 *** ... ..( 21 skipped). .. *** 161 2017-12-23 09:38 22 *** 162 2017-12-23 09:39 ? - 163 2017-12-23 09:40 15 - 164 2017-12-23 09:41 15 - 165 2017-12-23 09:42 16 - 166 2017-12-23 09:43 16 - 167 2017-12-23 09:44 17 - ... ..( 5 skipped). .. - 173 2017-12-23 09:50 17 - 174 2017-12-23 09:51 18 - ... ..( 9 skipped). .. - 184 2017-12-23 10:01 18 - 185 2017-12-23 10:02 19 - ... ..( 7 skipped). .. - 193 2017-12-23 10:10 19 - 194 2017-12-23 10:11 20 * ... ..( 13 skipped). .. * 208 2017-12-23 10:25 20 * 209 2017-12-23 10:26 21 ** ... ..( 50 skipped). .. ** 260 2017-12-23 11:17 21 ** 261 2017-12-23 11:18 ? - 262 2017-12-23 11:19 13 - 263 2017-12-23 11:20 13 - 264 2017-12-23 11:21 14 - ... ..( 2 skipped). .. - 267 2017-12-23 11:24 14 - 268 2017-12-23 11:25 15 - 269 2017-12-23 11:26 15 - 270 2017-12-23 11:27 16 - 271 2017-12-23 11:28 16 - 272 2017-12-23 11:29 17 - ... ..( 4 skipped). .. - 277 2017-12-23 11:34 17 - 278 2017-12-23 11:35 18 - 279 2017-12-23 11:36 ? - 280 2017-12-23 11:37 22 *** ... ..( 20 skipped). .. *** 301 2017-12-23 11:58 22 *** SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) Device Statistics (GP/SMART Log 0x04) not supported Pending Defects log (GP Log 0x0c) not supported SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 1 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 1 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 911 Vendor specific