no keyboard after booting r235646 in laptop FS Amilo D 7830

Sun Jul 1 06:59:02 UTC 2012

El día Sunday, July 01, 2012 a las 06:29:28AM +0700, Erich Dollansky escribió:

Hi,

> > and no older versions. I will install the USB booted system to harddisk
> > and hope when booted from disk and not from USB the keyboard is working.
> > 

I installed the system r235646 to disk and it shows the same problem: no
keyboard;

> if 7.4 still runs but not anything after 8.0, it is most likely what I have written. Some USB hardware is not supported anymore in 8 and later.
> 
> I would install the old one just to see  You will also know wat hwardware is used there and how it is supported.
> 
> This might be the faster route before starting debugging something which is not there.

I said already that it works with a r214444 version, CURRENT from
October 2010; so I booted this again and concerning keyboard, here is
the diff:

r214444:

$ fgrep -i kb /tmp/dmesg-r214444.txt
kbd1 at kbdmux0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0

$ ls -l /dev/kb*
lrwxr-xr-x  1 root  wheel         6 Jul  1 08:39 /dev/kbd0 -> atkbd0
lrwxr-xr-x  1 root  wheel         7 Jul  1 08:39 /dev/kbd1 -> kbdmux0
crw-------  1 root  wheel    0,  17 Jul  1 08:39 /dev/kbdmux0

r235646:

$ fgrep -i kb /tmp/dmesg-r235646.txt 
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
sc0: fb0, kbd1, terminal emulator: scteken (teken terminal)
atkbdc0 failed to probe at port 0x60 on isa0

$ ls -l /dev/kb*
lrwxr-xr-x  1 root  wheel         7 Jul  1 08:39 /dev/kbd1 -> kbdmux0
crw-------  1 root  wheel    0,  17 Jul  1 08:39 /dev/kbdmux0

the complete /tmp/dmesg-r214444.txt is attached, the
/tmp/dmesg-r235646.txt was in some message of this thread;

So the question is: why the <Keyboard controller (i8042)> is not
detected anymore in r235646, while it is in r214444?

Thanks

	matthias
-- 
Matthias Apitz
t +49-89-61308 351 - f +49-89-61308 399 - m +49-170-4527211
e <guru at unixarea.de> - w http://www.unixarea.de/
UNIX since V7 on PDP-11 | UNIX on mainframe since ESER 1055 (IBM /370)
UNIX on x86 since SVR4.2 UnixWare 2.1.2 | FreeBSD since 2.2.5
-------------- next part --------------
Copyright (c) 1992-2010 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 9.0-CURRENT #1 r214444: Thu Oct 28 10:56:32 CEST 2010
    guru at current.Sisis.de:/usr/home/guru/myThings/FreeBSD/9-CURRENT/obj/usr/home/guru/myThings/FreeBSD/9-CURRENT/src/sys/GENERIC i386
WARNING: WITNESS option enabled, expect reduced performance.
CPU: Intel(R) Pentium(R) 4 CPU 2.40GHz (2398.34-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0xf27  Family = f  Model = 2  Stepping = 7
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0x4400<CNXT-ID,xTPR>
real memory  = 1073741824 (1024 MB)
avail memory = 1031737344 (983 MB)
Event timer "LAPIC" quality 400
ACPI APIC Table: <A M I  OEMAPIC >
ioapic0 <Version 2.0> irqs 0-23 on motherboard
kbd1 at kbdmux0
acpi0: <A M I OEMRSDT> on motherboard
acpi0: Power Button (fixed)
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, 3ff00000 (3) failed
Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_ec0: <Embedded Controller: GPE 0x1c> port 0x62,0x66 on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
agp0: <Intel 82845G host to AGP bridge> on hostb0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0xb000-0xb0ff mem 0xd0000000-0xd7ffffff,0xffcf0000-0xffcfffff irq 16 at device 0.0 on pci1
uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0xdf20-0xdf3f irq 16 at device 29.0 on pci0
uhci0: LegSup = 0x2f00
usbus0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0
uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0xdf40-0xdf5f irq 19 at device 29.1 on pci0
uhci1: LegSup = 0x2f00
usbus1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1
uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0xdf80-0xdf9f irq 18 at device 29.2 on pci0
uhci2: LegSup = 0x2f00
usbus2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2
ehci0: <Intel 82801DB/L/M (ICH4) USB 2.0 controller> mem 0xffeffc00-0xffefffff irq 23 at device 29.7 on pci0
usbus3: EHCI version 1.0
usbus3: <Intel 82801DB/L/M (ICH4) USB 2.0 controller> on ehci0
pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci2: <ACPI PCI bus> on pcib2
cbb0: <O2Micro OZ6912/6972 PCI-CardBus Bridge> at device 3.0 on pci2
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
fwohci0: <VIA Fire II (VT6306)> port 0xcc00-0xcc7f mem 0xffdff800-0xffdfffff irq 18 at device 10.0 on pci2
fwohci0: OHCI version 1.10 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:03:0d:49:75:50:7a:e8
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:03:0d:50:7a:e8
fwe0: Ethernet address: 02:03:0d:50:7a:e8
fwip0: <IP over FireWire> on firewire0
fwip0: Firewire address: 00:03:0d:49:75:50:7a:e8 @ 0xfffe00000000, S400, maxrec 2048
sbp0: <SBP-2/SCSI over FireWire> on firewire0
dcons_crom0: <dcons configuration ROM> on firewire0
dcons_crom0: bus_addr 0x14ac000
fwohci0: Initiate bus reset
fwohci0: fwohci_intr_core: BUS reset
fwohci0: fwohci_intr_core: node_id=0x00000000, SelfID Count=1, CYCLEMASTER mode
sis0: <NatSemi DP8381[56] 10/100BaseTX> port 0xc800-0xc8ff mem 0xffdfe000-0xffdfefff irq 17 at device 12.0 on pci2
sis0: Silicon Revision: DP83816A
miibus0: <MII bus> on sis0
nsphyter0: <DP83815 10/100 media interface> PHY 0 on miibus0
nsphyter0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis0: Ethernet address: 00:a0:cc:df:75:57
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH4 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 31.1 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
pci0: <multimedia, audio> at device 31.5 (no driver attached)
pci0: <simple comms, generic modem> at device 31.6 (no driver attached)
acpi_button0: <Sleep Button> on acpi0
acpi_button1: <Power Button> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
battery0: <ACPI Control Method Battery> on acpi0
acpi_acad0: <AC Adapter> on acpi0
attimer0: <AT timer> port 0x40-0x43 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0
Event timer "RTC" frequency 32768 Hz quality 0
ppc0: <Parallel port> port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
acpi_lid0: <Control Method Lid Switch> on acpi0
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xcffff,0xd0000-0xd0fff pnpid ORM0000 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model Generic PS/2 mouse, device ID 0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
Timecounter "TSC" frequency 2398341748 Hz quality 800
Timecounters tick every 1.000 msec
firewire0: 1 nodes, maxhop <= 0 cable IRM irm(0)  (me) 
firewire0: bus manager 0 
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 480Mbps High Speed USB v2.0
ad0: 76319MB <IC25N080ATMR04 0 MO4OAC0J> at ata0-master UDMA100 
ugen0.1: <Intel> at usbus0
uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <Intel> at usbus2
uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
ugen3.1: <Intel> at usbus3
uhub3: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus3
acd0: CDRW <DVD+RW RW8160/1.03> at ata1-master UDMA33 
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub2: 2 ports with 2 removable, self powered
uhub3: 6 ports with 6 removable, self powered
ugen3.2: <SMI Technology> at usbus3
umass0: <SMI Technology Intenso Premium Line, class 0/0, rev 2.00/10.00, addr 2> on usbus3
umass0:  SCSI over Bulk-Only; quirks = 0x0000
umass0:1:0:-1: Attached to scbus1
da0 at umass-sim0 bus 0 scbus1 target 0 lun 0
da0: <Intenso Premium > Removable Direct Access SCSI-0 device 
da0: 40.000MB/s transfers
da0: 7560MB (15482880 512 byte sectors: 255H 63S/T 963C)
WARNING: WITNESS option enabled, expect reduced performance.
Trying to mount root from ufs:/dev/da0s1a [rw]...