ahci timeout

Barbara barbara.xxx1975 at libero.it
Wed Dec 29 17:38:03 UTC 2010



>From : ndenev at gmail.com
>
>On 27 Dec, 2010, at 21:20 , Barbara wrote:
>
>> 
>> As my old PATA hard disk was failing, I had to replace it with a new SATA 
>> drive where I moved my FreeBSDs installations, as PATA drives are not easy 
to 
>> find these days.
>> So I had to move one of my data drive from a VIA8237A SATA controller to 
the 
>> last free SATA slot on a Marvell 88SX6121 to make room for the new hd.
>> The hd I moved was working perfectly when connected to the VIA controller.
>> Now, with the Marvell I'm getting messages like the following twos while 
using 
>> the disk:
>>    ahcich0: Timeout on slot 10
>>    ahcich0: is 00000000 cs 3ffff800 ss 3ffffc00 rs 3ffffc00 tfd 50010040 
serr 
>> 00000000
>> 
>>    ahcich0: Timeout on slot 5
>>    ahcich0: is 00000000 cs 00000180 ss 000001e0 rs 000001e0 tfd 50040040 
serr 
>> 00000000
>> 
>> This doesn't happen regularly. For example downloading from a slow website 
on 
>> it, so few kb/s, is ok.
>> But if I copy files from the disk attacked to the Marvell controller to 
>> another another disk, or for example run md5 on some files, it's very 
likely to 
>> happen.
>> The process accessing the disk can not be killed even with -9, ^C does 
>> nothing, and umount doesn't exit.
>> If I'm copying files on it from another disk it can't be unmounted too as 
the 
>> unkillable process has it in use.
>> On shutdown many disk doesn't get unmounted, so there are a lot of fsck on 
>> boot, and on CURRENT (last built yesterday), FreeBSD enter debugger as it 
fail 
>> flushing disk caches.
>> 
>> Relevant part from dmesg:
>> 
>> atapci0: <Marvell 88SX6121 UDMA133 controller> port 0xdc00-0xdc07,0xd880-
>> 0xd883,0xd800-0xd807,0xd480-0xd483,0xd400-0xd40f mem 0xfbdffc00-0xfbdfffff 
irq 
>> 28 at device 0.0 on pci6
>> ahci0: <Marvell 88SX6121 AHCI SATA controller> on atapci0
>> ahci0: AHCI v1.00 with 2 3Gbps ports, Port Multiplier supported
>> ahcich0: <AHCI channel> at channel 0 on ahci0
>> ahcich1: <AHCI channel> at channel 1 on ahci0
>> ata2: <ATA channel 0> on atapci0
>> atapci1: <VIA 8237A SATA150 controller> port 0xbc00-0xbc07,0xb880-0xb883,
>> 0xb800-0xb807,0xb480-0xb483,0xb400-0xb40f,0xb000-0xb0ff irq 21 at device 
15.0 
>> on pci0
>> ata3: <ATA channel 0> on atapci1
>> ata4: <ATA channel 1> on atapci1
>> atapci2: <VIA 8237A UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,
>> 0x376,0xfc00-0xfc0f at device 15.1 on pci0
>> ata0: <ATA channel 0> on atapci2
>> ata1: <ATA channel 1> on atapci2
>> 
>> ada0 at ahcich0 bus 0 scbus0 target 0 lun 0
>> ada0: <ST31000528AS CC44> ATA-8 SATA 2.x device
>> ada0: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
>> ada0: Command Queueing enabled
>> ada0: 953869MB (1953525168 512 byte sectors: 16H 63S/T 16383C)
>> ada1 at ata3 bus 0 scbus3 target 0 lun 0
>> ada1: <WDC WD2500KS-00MJB0 02.01C03> ATA-7 SATA 2.x device
>> ada1: 150.000MB/s transfers (SATA 1.x, UDMA5, PIO 8192bytes)
>> ada1: 238475MB (488397168 512 byte sectors: 16H 63S/T 16383C)
>> ada2 at ata4 bus 0 scbus4 target 0 lun 0
>> ada2: <ST3500320AS SD1A> ATA-8 SATA 1.x device
>> ada2: 150.000MB/s transfers (SATA 1.x, UDMA5, PIO 8192bytes)
>> ada2: 476940MB (976773168 512 byte sectors: 16H 63S/T 16383C)
>> ada3 at ata0 bus 0 scbus5 target 0 lun 0
>> ada3: <MAXTOR STM3160212A 3.AAJ> ATA-7 device
>> ada3: 100.000MB/s transfers (UDMA5, PIO 8192bytes)
>> ada3: 152627MB (312581808 512 byte sectors: 16H 63S/T 16383C)
>> 
>> _______________________________________________
>> freebsd-current at freebsd.org mailing list
>> http://lists.freebsd.org/mailman/listinfo/freebsd-current
>> To unsubscribe, send any mail to "freebsd-current-unsubscribe at freebsd.org"
>
>Just to add a "me too".
>
>I'm running -STABLE but have the same problems with Marvell 88SX6121 giving 
"ahci timeout" messages.
>
>Regards,
>Nikolay
>

Nikolay, thanks for the feedback, even if unfortunately it's negative...
I see that in both 8-STABLE (8.2-PRERELEASE now) and 9.0-CURRENT, both rebuilt 
no more than a week ago.
I've also tried rebuilding the kernel with:
   options         CAMDEBUG
   options         CAM_DEBUG_BUS=0
   options         CAM_DEBUG_TARGET=0
   options         CAM_DEBUG_LUN=0
   options         CAM_DEBUG_FLAGS=CAM_DEBUG_TRACE
(0 is the bus/target/lun of the marvell controller/attached hd)
and run a test computing md5 for about 60GB of files.
Obviously, as the debug options where active, it run successfully without any 
problems :)
Is there any other info I should provide or any other test that I can do?

Thanks
Barbara



More information about the freebsd-current mailing list