Broadcom NIC not recognized by FreeBSD?

[Craig Rodrigues]

On Wed, Jun 10, 2009 at 05:42:11PM +0000, Craig Rodrigues wrote:
> Hi,
> 
> I am trying to install FreeBSD-CURRENT (svn rev 189289) on my Acer Aspire 5920
> laptop.  The Broadcom NIC does not show up
> in the list of interfaces with "ifconfig -l".
> 
> However, if I do "pciconf -l -v", I see:
> 
> bge0 at pci0:8:0:0:  class=0x020000 card=0x01211025 chip=0x169314e4 rev=0x02 hdr=0x00
>   vendor = 'Broadcom Corporation'
>   device = 'BCM 5787A Ethernet Controller Broadcom Netlink Gigabit'
>   class  = network
>   subclass = ethernet

Here is the dmesg.boot

-- 
Craig Rodrigues
rodrigc at crodrigues.org
-------------- next part --------------
Copyright (c) 1992-2009 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.0-CURRENT #8 r189289M: Mon Mar  2 17:36:30 PST 2009
    root at rodrigc-bsd2:/usr/obj/usr/src/sys/GENERIC_DTRACE
WARNING: WITNESS option enabled, expect reduced performance.
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Core(TM)2 Duo CPU     T5450  @ 1.66GHz (1666.79-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x6fd  Stepping = 13
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0xe39d<SSE3,DTES64,MON,DS_CPL,EST,TM2,SSSE3,CX16,xTPR,PDCM>
  AMD Features=0x20100000<NX,LM>
  AMD Features2=0x1<LAHF>
  TSC: P-state invariant
  Cores per package: 2
real memory  = 2137849856 (2038 MB)
avail memory = 2079494144 (1983 MB)
ACPI APIC Table: <INTEL  CRESTLNE>
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
ioapic0: Changing APIC ID to 1
ioapic0 <Version 2.0> irqs 0-23 on motherboard
kbd1 at kbdmux0
acpi0: <ACRSYS ACRPRDCT> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
unknown: I/O range not supported
Timecounter "HPET" frequency 14318180 Hz quality 900
Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
acpi_ec0: <Embedded Controller: GPE 0x18> port 0x62,0x66 on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
vgapci0: <VGA-compatible display> port 0x1800-0x1807 mem 0xf0000000-0xf00fffff,0xd0000000-0xdfffffff irq 16 at device 2.0 on pci0
agp0: <Intel GM965 SVGA controller> on vgapci0
agp0: detected 7676k stolen memory
agp0: aperture size is 256M
vgapci1: <VGA-compatible display> mem 0xf0100000-0xf01fffff at device 2.1 on pci0
uhci0: <Intel 82801H (ICH8) USB controller USB-D> port 0x1820-0x183f irq 16 at device 26.0 on pci0
uhci0: [ITHREAD]
uhci0: LegSup = 0x003b
usbus0: <Intel 82801H (ICH8) USB controller USB-D> on uhci0
uhci1: <Intel 82801H (ICH8) USB controller USB-E> port 0x1840-0x185f irq 21 at device 26.1 on pci0
uhci1: [ITHREAD]
uhci1: LegSup = 0x0010
usbus1: <Intel 82801H (ICH8) USB controller USB-E> on uhci1
ehci0: <Intel 82801H (ICH8) USB 2.0 controller USB2-B> mem 0xf0704800-0xf0704bff irq 18 at device 26.7 on pci0
ehci0: [ITHREAD]
usbus2: EHCI version 1.0
usbus2: <Intel 82801H (ICH8) USB 2.0 controller USB2-B> on ehci0
pci0: <multimedia, HDA> at device 27.0 (no driver attached)
pcib1: <ACPI PCI-PCI bridge> irq 17 at device 28.0 on pci0
pci2: <ACPI PCI bus> on pcib1
pcib2: <ACPI PCI-PCI bridge> irq 19 at device 28.3 on pci0
pci6: <ACPI PCI bus> on pcib2
pci6: <network> at device 0.0 (no driver attached)
pcib3: <ACPI PCI-PCI bridge> irq 16 at device 28.5 on pci0
pci8: <ACPI PCI bus> on pcib3
bge0: <Broadcom NetLink Gigabit Ethernet Controller, ASIC rev. 0xb002> irq 17 at device 0.0 on pci8
bge0: 0x10000 bytes of rid 0x10 res 3 failed (0, 0xffffffff).
bge0: couldn't map memory
device_attach: bge0 attach returned 6
uhci2: <Intel 82801H (ICH8) USB controller USB-A> port 0x1860-0x187f irq 23 at device 29.0 on pci0
uhci2: [ITHREAD]
uhci2: LegSup = 0x003b
usbus3: <Intel 82801H (ICH8) USB controller USB-A> on uhci2
uhci3: <Intel 82801H (ICH8) USB controller USB-B> port 0x1880-0x189f irq 19 at device 29.1 on pci0
uhci3: [ITHREAD]
uhci3: LegSup = 0x0010
usbus4: <Intel 82801H (ICH8) USB controller USB-B> on uhci3
uhci4: <Intel 82801H (ICH8) USB controller USB-C> port 0x18a0-0x18bf irq 18 at device 29.2 on pci0
uhci4: [ITHREAD]
uhci4: LegSup = 0x0010
usbus5: <Intel 82801H (ICH8) USB controller USB-C> on uhci4
ehci1: <Intel 82801H (ICH8) USB 2.0 controller USB2-A> mem 0xf0704c00-0xf0704fff irq 23 at device 29.7 on pci0
ehci1: [ITHREAD]
usbus6: EHCI version 1.0
usbus6: <Intel 82801H (ICH8) USB 2.0 controller USB2-A> on ehci1
pcib4: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci10: <ACPI PCI bus> on pcib4
fwohci0: <1394 Open Host Controller Interface> mem 0xf0400000-0xf04007ff at device 9.0 on pci10
fwohci0: [ITHREAD]
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:24:1b:00:56:34:12:00
fwohci0: Phy 1394a available S400, 1 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
dcons_crom0: <dcons configuration ROM> on firewire0
dcons_crom0: bus_addr 0x149c000
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:24:1b:34:12:00
fwe0: Ethernet address: 02:24:1b:34:12:00
fwip0: <IP over FireWire> on firewire0
fwip0: Firewire address: 00:24:1b:00:56:34:12:00 @ 0xfffe00000000, S400, maxrec 2048
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: fwohci_intr_core: BUS reset
fwohci0: fwohci_intr_core: node_id=0x00000000, SelfID Count=1, CYCLEMASTER mode
pci10: <base peripheral, SD host controller> at device 9.1 (no driver attached)
pci10: <base peripheral> at device 9.2 (no driver attached)
pci10: <base peripheral> at device 9.3 (no driver attached)
pci10: <base peripheral> at device 9.4 (no driver attached)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH8M UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1810-0x181f at device 31.1 on pci0
ata0: <ATA channel 0> on atapci0
ata0: [ITHREAD]
atapci1: <Intel AHCI controller> port 0x1c00-0x1c07,0x18d4-0x18d7,0x18d8-0x18df,0x18d0-0x18d3,0x18e0-0x18ff mem 0xf0704000-0xf07047ff irq 19 at device 31.2 on pci0
atapci1: [ITHREAD]
atapci1: AHCI Version 01.10 controller with 3 ports PM not supported
ata2: <ATA channel 0> on atapci1
ata2: [ITHREAD]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
acpi_acad0: <AC Adapter> on acpi0
battery0: <ACPI Control Method Battery> on acpi0
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
atrtc0: <AT realtime clock> port 0x70-0x77 irq 8 on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model Generic PS/2 mouse, device ID 0
cpu0: <ACPI CPU> on acpi0
est0: <Enhanced SpeedStep Frequency Control> on cpu0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
cpu1: <ACPI CPU> on acpi0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
p4tcc1: <CPU Frequency Thermal Control> on cpu1
pmtimer0 on isa0
orm0: <ISA Option ROM> at iomem 0xe0000-0xe17ff pnpid ORM0000 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ppc0: parallel port not found.
Timecounters tick every 1.000 msec
firewire0: 1 nodes, maxhop <= 0 cable IRM irm(0)  (me) 
firewire0: bus manager 0 
usbus6: 480Mbps High Speed USB v2.0
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 480Mbps High Speed USB v2.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 12Mbps Full Speed USB v1.0
usbus5: 12Mbps Full Speed USB v1.0
ugen0.1: <Intel> at usbus0
uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <Intel> at usbus2
uhub2: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
ugen3.1: <Intel> at usbus3
uhub3: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
ugen4.1: <Intel> at usbus4
uhub4: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4
ugen5.1: <Intel> at usbus5
uhub5: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5
ugen6.1: <Intel> at usbus6
uhub6: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus6
acd0: DVDR <HL-DT-ST DVDRAM GSA-T20N/WP03> at ata0-master UDMA33
ad4: 238475MB <WDC WD2500BEVS-22UST0 01.01A01> at ata2-master SATA150
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub3: 2 ports with 2 removable, self powered
uhub4: 2 ports with 2 removable, self powered
uhub5: 2 ports with 2 removable, self powered
acd0: FAILURE - READ_BIG ILLEGAL REQUEST asc=0x64 ascq=0x00 
GEOM_LABEL: Label for provider acd0 is iso9660/FreeBSD Boot.
acd0: FAILURE - READ_BIG ILLEGAL REQUEST asc=0x64 ascq=0x00 
acpi_ec0: wait timed out (response), forcing polled mode
uhub2: 4 ports with 4 removable, self powered
acpi_ec0: warning: EC done before starting event wait
GEOM: ad4: partition 4 does not start on a track boundary.
GEOM: ad4: partition 4 does not end on a track boundary.
GEOM: ad4: partition 3 does not start on a track boundary.
GEOM: ad4: partition 3 does not end on a track boundary.
GEOM: ad4: partition 2 does not start on a track boundary.
GEOM: ad4: partition 2 does not end on a track boundary.
GEOM_LABEL: Label for provider ad4s1 is ntfs/PQSERVICE.
GEOM_LABEL: Label for provider ad4s2 is ntfs/ACER.
GEOM_LABEL: Label for provider ad4s3 is ntfs/DATA.
uhub6: 6 ports with 6 removable, self powered
ugen2.2: <SuYin> at usbus2
ugen6.2: <I0MEGA> at usbus6
umass0: <I0MEGA Mini512MB*IOM2B5, class 0/0, rev 2.00/0.71, addr 2> on usbus6
umass0:  SCSI over Bulk-Only; quirks = 0x0000
umass0:1:0:-1: Attached to scbus1
(probe7:umass-sim0:0:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 
(probe7:umass-sim0:0:0:0): CAM Status: SCSI Status Error
(probe7:umass-sim0:0:0:0): SCSI Status: Check Condition
(probe7:umass-sim0:0:0:0): UNIT ATTENTION asc:28,0
(probe7:umass-sim0:0:0:0): Not ready to ready change, medium may have changed
(probe7:umass-sim0:0:0:0): Retrying Command (per Sense Data)
cam_periph_alloc: attempt to re-allocate valid device da0 rejected
daasync: Unable to attach to new device due to status 0x6
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <I0MEGA Mini512MB*IOM2B5 2.10> Removable Direct Access SCSI-0 device 
da0: 40.000MB/s transfers
da0: 497MB (1017856 512 byte sectors: 64H 32S/T 497C)
SMP: AP CPU #1 Launched!
WARNING: WITNESS option enabled, expect reduced performance.
Trying to mount root from cd9660:/dev/acd0