8.0-BETA1 on a HP DL585 Issues

[Andrew Tulloch]

I've upgraded one of our HP DL585's (4xdual core opteron, 16GB ram)
from 7.2 to 8.0-BETA1 and seem to have a couple of issues.

Firstly the machine will no longer shutdown or reboot, it just sits at
the Uptime:: XXXX prompt and doesn't reboot or power off, no
Rebooting/cpu_reset() messages.

Secondly, sometimes the machine will not boot, it'll load the kernel
and start, but then hang at:
pcib0: <ACPI Host-PCI bridge> on acpi0

The same seems to happen with GENERIC and a kernel config minus
witness etc for speed.

If I revert to the 7.2 kernel it's fine.

Any suggestions on things I can try?

Full dmesg attached.

Thanks,
Andrew
-------------- next part --------------
Copyright (c) 1992-2009 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.0-BETA1 #2: Tue Jul 14 09:55:31 BST 2009
    root at XXXXX:/usr/obj/usr/src/sys/NODEBUG
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: AMD Opteron (tm) Processor 875 (2199.94-MHz K8-class CPU)
  Origin = "AuthenticAMD"  Id = 0x20f10  Stepping = 0
  Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
  Features2=0x1<SSE3>
  AMD Features=0xe2500800<SYSCALL,NX,MMX+,FFXSR,LM,3DNow!+,3DNow!>
  AMD Features2=0x2<CMP>
real memory  = 17179869184 (16384 MB)
avail memory = 16403906560 (15643 MB)
ACPI APIC Table: <HP     00000083>
FreeBSD/SMP: Multiprocessor System Detected: 8 CPUs
FreeBSD/SMP: 4 package(s) x 2 core(s)
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
 cpu2 (AP): APIC ID:  2
 cpu3 (AP): APIC ID:  3
 cpu4 (AP): APIC ID:  4
 cpu5 (AP): APIC ID:  5
 cpu6 (AP): APIC ID:  6
 cpu7 (AP): APIC ID:  7
ACPI Warning: Invalid length for Pm1aControlBlock: 32, using default 16 20090521 tbfadt-707
ACPI Warning: Invalid length for Pm1bControlBlock: 32, using default 16 20090521 tbfadt-707
MADT: Forcing active-low polarity and level trigger for SCI
ioapic0 <Version 1.1> irqs 0-23 on motherboard
ioapic1 <Version 1.1> irqs 24-27 on motherboard
ioapic2 <Version 1.1> irqs 28-31 on motherboard
ioapic3 <Version 1.1> irqs 32-35 on motherboard
ioapic4 <Version 1.1> irqs 36-39 on motherboard
ioapic5 <Version 1.1> irqs 40-43 on motherboard
ioapic6 <Version 1.1> irqs 44-47 on motherboard
kbd1 at kbdmux0
acpi0: <HP A01> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x908-0x90b on acpi0
pcib0: <ACPI Host-PCI bridge> on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> at device 3.0 on pci0
pci1: <ACPI PCI bus> on pcib1
ohci0: <OHCI (generic) USB controller> mem 0xf7af0000-0xf7af0fff irq 19 at device 0.0 on pci1
ohci0: [ITHREAD]
usbus0: <OHCI (generic) USB controller> on ohci0
ohci1: <OHCI (generic) USB controller> mem 0xf7ae0000-0xf7ae0fff irq 19 at device 0.1 on pci1
ohci1: [ITHREAD]
usbus1: <OHCI (generic) USB controller> on ohci1
pci1: <base peripheral> at device 2.0 (no driver attached)
pci1: <base peripheral> at device 2.2 (no driver attached)
vgapci0: <VGA-compatible display> port 0x4400-0x44ff mem 0xf6000000-0xf6ffffff,0xf5ff0000-0xf5ff0fff at device 3.0 on pci1
isab0: <PCI-ISA bridge> at device 4.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <AMD 8111 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x2000-0x200f at device 4.1 on pci0
ata0: <ATA channel 0> on atapci0
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
ata1: [ITHREAD]
pci0: <bridge> at device 4.3 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> at device 7.0 on pci0
pci2: <ACPI PCI bus> on pcib2
ciss0: <Compaq Smart Array 5i> port 0x5000-0x50ff mem 0xf7bc0000-0xf7bfffff,0xf5ef0000-0xf5ef3fff irq 18 at device 4.0 on pci2
ciss0: PERFORMANT Transport
ciss0: [ITHREAD]
pci0:2:6:0: failed to read VPD data.
bge0: <Broadcom BCM5704 B0, ASIC rev. 0x2100> mem 0xf7bb0000-0xf7bbffff irq 25 at device 6.0 on pci2
miibus0: <MII bus> on bge0
brgphy0: <BCM5704 10/100/1000baseTX PHY> PHY 1 on miibus0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bge0: Ethernet address: 00:13:21:69:f5:25
bge0: [ITHREAD]
bge1: <HP NC7782 Gigabit Server Adapter, ASIC rev. 0x2100> mem 0xf7ba0000-0xf7baffff irq 24 at device 6.1 on pci2
miibus1: <MII bus> on bge1
brgphy1: <BCM5704 10/100/1000baseTX PHY> PHY 1 on miibus1
brgphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
bge1: Ethernet address: 00:13:21:69:f5:24
bge1: [ITHREAD]
pcib3: <ACPI PCI-PCI bridge> at device 8.0 on pci0
pci3: <ACPI PCI bus> on pcib3
pcib4: <ACPI Host-PCI bridge> on acpi0
pci4: <ACPI PCI bus> on pcib4
pcib5: <ACPI PCI-PCI bridge> at device 9.0 on pci4
pci5: <ACPI PCI bus> on pcib5
isp0: <Qlogic ISP 2312 PCI FC-AL Adapter> port 0x6000-0x60ff mem 0xf7cf0000-0xf7cf0fff irq 32 at device 13.0 on pci5
isp0: [ITHREAD]
isp0: Polled Mailbox Command (0x2) Timeout (1000000us)
isp0: Polled Mailbox Command (0x8) Timeout (100000us)
isp0: Mailbox Command 'ABOUT FIRMWARE' failed (TIMEOUT)
device_attach: isp0 attach returned 6
pcib6: <ACPI PCI-PCI bridge> at device 10.0 on pci4
pci6: <ACPI PCI bus> on pcib6
isp1: <Qlogic ISP 2312 PCI FC-AL Adapter> port 0x7000-0x70ff mem 0xf7df0000-0xf7df0fff irq 36 at device 14.0 on pci6
isp1: [ITHREAD]
isp1: Board Type 2312, Chip Revision 0x2, resident F/W Revision 18771.20512.8224
device_attach: isp1 attach returned 6
pcib7: <ACPI PCI-PCI bridge> at device 11.0 on pci4
pci7: <ACPI PCI bus> on pcib7
pcib8: <PCI-PCI bridge> at device 10.0 on pci7
pci8: <PCI bus> on pcib8
em0: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0x8000-0x803f mem 0xf7ee0000-0xf7efffff irq 42 at device 4.0 on pci8
em0: [FILTER]
em0: Ethernet address: 00:04:23:bf:ef:20
em1: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0x8040-0x807f mem 0xf7ec0000-0xf7edffff irq 43 at device 4.1 on pci8
em1: [FILTER]
em1: Ethernet address: 00:04:23:bf:ef:21
em2: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0x8080-0x80bf mem 0xf7ea0000-0xf7ebffff irq 40 at device 6.0 on pci8
em2: [FILTER]
em2: Ethernet address: 00:04:23:bf:ef:22
em3: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0x80c0-0x80ff mem 0xf7e80000-0xf7e9ffff irq 41 at device 6.1 on pci8
em3: [FILTER]
em3: Ethernet address: 00:04:23:bf:ef:23
pcib9: <ACPI PCI-PCI bridge> at device 12.0 on pci4
pci9: <ACPI PCI bus> on pcib9
pcib10: <PCI-PCI bridge> at device 12.0 on pci9
pci10: <PCI bus> on pcib10
em4: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0x9000-0x903f mem 0xf7fe0000-0xf7ffffff irq 46 at device 4.0 on pci10
em4: [FILTER]
em4: Ethernet address: 00:04:23:bf:ef:d4
em5: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0x9040-0x907f mem 0xf7fc0000-0xf7fdffff irq 47 at device 4.1 on pci10
em5: [FILTER]
em5: Ethernet address: 00:04:23:bf:ef:d5
em6: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0x9080-0x90bf mem 0xf7fa0000-0xf7fbffff irq 44 at device 6.0 on pci10
em6: [FILTER]
em6: Ethernet address: 00:04:23:bf:ef:d6
em7: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0x90c0-0x90ff mem 0xf7f80000-0xf7f9ffff irq 45 at device 6.1 on pci10
em7: [FILTER]
em7: Ethernet address: 00:04:23:bf:ef:d7
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model Generic PS/2 mouse, device ID 0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
uart0: [FILTER]
fdc1: <floppy drive controller (FDE)> port 0x3f2-0x3f5 irq 6 drq 2 on acpi0
fdc1: [FILTER]
fd0: <1440-KB 3.5" drive> on fdc1 drive 0
cpu0: <ACPI CPU> on acpi0
powernow0: <Cool`n'Quiet K8> on cpu0
cpu1: <ACPI CPU> on acpi0
powernow1: <Cool`n'Quiet K8> on cpu1
cpu2: <ACPI CPU> on acpi0
powernow2: <Cool`n'Quiet K8> on cpu2
cpu3: <ACPI CPU> on acpi0
powernow3: <Cool`n'Quiet K8> on cpu3
cpu4: <ACPI CPU> on acpi0
powernow4: <Cool`n'Quiet K8> on cpu4
cpu5: <ACPI CPU> on acpi0
powernow5: <Cool`n'Quiet K8> on cpu5
cpu6: <ACPI CPU> on acpi0
powernow6: <Cool`n'Quiet K8> on cpu6
cpu7: <ACPI CPU> on acpi0
powernow7: <Cool`n'Quiet K8> on cpu7
orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xee000-0xeffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
atrtc0: <AT Real Time Clock> at port 0x70 irq 8 on isa0
fdc0: No FDOUT register!
ppc0: cannot reserve I/O port range
uart1: <Non-standard ns8250 class UART with FIFOs> at port 0x2f8-0x2ff irq 3 on isa0
uart1: [FILTER]
Timecounters tick every 1.000 msec
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
acd0: CDROM <CD-224E/9.9A> at ata0-master PIO4
ugen0.1: <AMD> at usbus0
uhub0: <AMD OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <AMD> at usbus1
uhub1: <AMD OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
uhub0: 3 ports with 3 removable, self powered
uhub1: 3 ports with 3 removable, self powered
ugen1.2: <Dell> at usbus1
ukbd0: <Dell Dell USB Keyboard, class 0/0, rev 1.10/3.06, addr 2> on usbus1
kbd2 at ukbd0
ugen1.3: <Logitech> at usbus1
ums0: <Logitech USB-PS/2 Optical Mouse, class 0/0, rev 2.00/18.00, addr 3> on usbus1
ums0: 6 buttons and [XYZ] coordinates ID=0
da0 at ciss0 bus 0 target 0 lun 0SMP: AP CPU #1 Launched!
da0: 
<COMPAQ RAID 1  VOLUME OK> Fixed Direct Access SCSI-4 device SMP: AP CPU #6 Launched!
da0: 135.168MB/s transfers
SMP: AP CPU #7 Launched!
da0: Command Queueing enabled
SMP: AP CPU #2 Launched!
da0: 286095MB (585922680 512 byte sectors: 255H 63S/T 36472C)
SMP: AP CPU #3 Launched!

SMP: AP CPU #5 Launched!
SMP: AP CPU #4 Launched!
Trying to mount root from ufs:/dev/da0s1a
em0: link state changed to UP