"interrupt storm..."; seems associated with an0 NIC
Ilya Orehov
elias at artx.ru
Tue Dec 9 19:24:46 UTC 2008
+------- M. Warner Losh, 2008-12-09 -------
| In message: <20081209141908.GA15845 at artx.ru>
| Ilya Orehov <elias at artx.ru> writes:
| : +------- M. Warner Losh, 2008-12-05 -------
| : | Thanks. Grump. Will have to back out and try again.
| :
| : Hello!
| :
| : I see storm too, but with 32-bit cards.
| :
| : Thinkpad 600X, two cardbus cards: xl0 and ath0.
| :
| : Since pccbb.c 1.176 and pccbb_pci.c 1.30
| : after rebooting with card(s) inserted or inserting any card
| : I see "interrupt storm...throttling..." messages about 1 per second.
| : Laptop remains usable, cards working.
| : Storm don't stop even if I eject all cards.
| : During storm, vmstat -i shows rate ~500 on cbb.
| : No messages appeared if laptop rebooted without cards
| : (until any card inserted).
| :
| : Later revisions ( pccbb.c 1.178 and pccbb_pci.c 1.31)
| : didn't bring any visible changes.
| :
| : But this hack helped.
| : No storm detected, vmstat -i shows rate 0 or 1 on cbb.
| :
| : diff -up xxx/pccbb_pci.c ./pccbb_pci.c
| : --- xxx/pccbb_pci.c 2008-12-06 11:56:00.000000000 +0300
| : +++ ./pccbb_pci.c 2008-12-09 14:08:03.000000000 +0300
| : @@ -689,6 +689,7 @@ cbb_pci_filt(void *arg)
| : struct cbb_softc *sc = arg;
| : uint32_t sockevent;
| : int retval = FILTER_STRAY;
| : + int ack = 0;
| :
| : /*
| : * Read the socket event. Sometimes, the theory goes, the PCI
| : @@ -722,6 +723,7 @@ cbb_pci_filt(void *arg)
| : sc->cardok = 0;
| : cbb_disable_func_intr(sc);
| : wakeup(&sc->intrhand);
| : + ack = 1;
| : }
| : /*
| : * If we get a power interrupt, wakeup anybody that might
| : @@ -732,7 +734,10 @@ cbb_pci_filt(void *arg)
| : cbb_set(sc, CBB_SOCKET_EVENT, CBB_SOCKET_EVENT_POWER);
| : sc->powerintr++;
| : wakeup((void *)&sc->powerintr);
| : + ack = 1;
| : }
| : + if (!ack)
| : + cbb_set(sc, CBB_SOCKET_EVENT, sockevent);
| : retval = FILTER_HANDLED;
| : }
| : /*
| :
| : Do you need dmesg or some other info?
|
| Can you please do the following:
|
| + if (!ack) {
| + printf("Need to ack %#x\n", sockevent);
| + cbb_set(sc, CBB_SOCKET_EVENT, sockevent);
| + }
|
| And let me know what it says?
Recompiled, rebooted with xl0 -
message printed only once after xl0 initialization:
"Need to ack 0x1"
Then I ejected xl0 - no message.
When the card was inserted back, same message appeared.
...
ad0: 57231MB <WDC WD600VE-07HDT0 09.07D09> at ata0-master UDMA33
xl0: <3Com 3c575TX Fast Etherlink XL> port 0x1000-0x103f irq 11 at device 0.0 on cardbus1
miibus0: <MII bus> on xl0
tdkphy0: <TDK 78Q2120 media interface> PHY 0 on miibus0
tdkphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl0: Ethernet address: 00:60:08:d2:38:56
xl0: [ITHREAD]
Need to ack 0x1
acd0: CDROM <TOSHIBA CD-ROM XM-1902B/1717> at ata1-master PIO4
Trying to mount root from ufs:/dev/ad0s2a
WARNING: attempt to net_add_domain(bluetooth) after domainfinalize()
xl0: reset didn't complete
xl0: command never completed!
xl0: command never completed!
xl0: command never completed!
tdkphy0: detached
miibus0: detached
xl0: detached
Need to ack 0x1
xl0: <3Com 3c575TX Fast Etherlink XL> port 0x1000-0x103f irq 11 at device 0.0 on cardbus1
miibus0: <MII bus> on xl0
tdkphy0: <TDK 78Q2120 media interface> PHY 0 on miibus0
tdkphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl0: Ethernet address: 00:60:08:d2:38:56
xl0: [ITHREAD]
xl0: link state changed to DOWN
xl0: link state changed to UP
regards,
Ilya.
|
| Warner
|
+-----------------------------
-------------- next part --------------
Copyright (c) 1992-2008 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.0-CURRENT #13: Tue Dec 9 21:34:37 MSK 2008
elias at .......ru:/usr/src/sys/i386/compile/TB
Preloaded elf kernel "/boot/kernel/kernel" at 0xc09ee000.
Preloaded elf module "/boot/kernel/snd_csa.ko" at 0xc09ee174.
Preloaded elf module "/boot/kernel/sound.ko" at 0xc09ee220.
Preloaded elf module "/boot/kernel/ng_ubt.ko" at 0xc09ee2cc.
Preloaded elf module "/boot/kernel/netgraph.ko" at 0xc09ee378.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc09ee428.
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 498274309 Hz
CPU: Intel Pentium III (498.27-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x681 Stepping = 1
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
Instruction TLB: 4 KB pages, 4-way set associative, 32 entries
Instruction TLB: 4 MB pages, fully associative, 2 entries
Data TLB: 4 KB pages, 4-way set associative, 64 entries
2nd-level cache: 256 KB, 8-way set associative, 32 byte line size
1st-level instruction cache: 16 KB, 4-way set associative, 32 byte line size
Data TLB: 4 MB Pages, 4-way set associative, 8 entries
1st-level data cache: 16 KB, 4-way set associative, 32 byte line size
real memory = 268238848 (255 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000c25000 - 0x000000000fb4dfff, 250777600 bytes (61225 pages)
avail memory = 253173760 (241 MB)
bios32: Found BIOS32 Service Directory header at 0xc00fd800
bios32: Entry = 0xfd820 (c00fd820) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xfd880+0x0
pnpbios: Found PnP BIOS data at 0xc00fe700
pnpbios: Entry = f0000:e724 Rev = 1.0
pnpbios: Event flag at 415
Other BIOS signatures found:
snd_unit_init() u=0x00ff8000 [512] d=0x00007c00 [32] c=0x000003ff [1024]
feeder_register: snd_unit=-1 snd_maxautovchans=16 latency=5 feeder_buffersize=16384 feeder_rate_min=1 feeder_rate_max=2016000 feeder_rate_round=25
ath_rate: version 1.9 <SampleRate bit-rate selection algorithm>
wlan: <802.11 Link Layer>
kbd: new array size 4
kbd1 at kbdmux0
mem: <memory>
Pentium Pro MTRR support enabled
io: <I/O>
null: <null device, zero device>
random: <entropy source, Software, Yarrow>
ACPI: RSDP @ 0x0xfd6e0/0x0014 (v 0 IBM )
ACPI: RSDT @ 0x0xffd0000/0x0028 (v 1 IBM TP600X 0x00000001 0x00000000)
ACPI: FACP @ 0x0xffd0100/0x0074 (v 1 IBM TP600X 0x00000001 0x00000000)
ACPI: DSDT @ 0x0xffd0200/0xAF9E (v 1 IBM TP600X 0x00000102 MSFT 0x0100000C)
ACPI: FACS @ 0x0xffdf000/0x0040
npx0: INT 16 interface
acpi0: <IBM TP600X> on motherboard
pci_open(1): mode 1 addr port (0x0cf8) is 0x80003b40
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71908086)
pcibios: BIOS version 2.10
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.ISA0.PIRQ -> bus 0 dev 1 func 0
acpi0: [MPSAFE]
acpi0: [ITHREAD]
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.CBS0.CBUS -> bus 0 dev 2 func 0
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.CBS1.CBUS -> bus 0 dev 2 func 1
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.PM00.X3DB -> bus 0 dev 7 func 3
acpi0: Power Button (fixed)
acpi0: wakeup code va 0xc1c5f000 pa 0x1000
atpic: Programming IRQ9 as level/low
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.IDE0.X140 -> bus 0 dev 7 func 1
acpi_bus_number: root bus has no _BBN, assuming 0
AcpiOsDerivePciId: \\_SB_.PCI0.DOCK.IDE1.X140 -> bus 0 dev 0 func 1
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, ff00000 (3) failed
ACPI timer: 0/5 0/5 0/5 0/5 0/5 0/5 0/5 0/5 0/5 0/4 -> 0
Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
acpi_timer0: <24-bit timer at 3.579545MHz> port 0xef08-0xef0b on acpi0
acpi_ec0: <Embedded Controller: GPE 0x9, GLK> port 0x62,0x66 on acpi0
pci_link0: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
Validation 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link1: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
Validation 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link2: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
Validation 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link3: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
Validation 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
acpi_lid0: <Control Method Lid Switch> on acpi0
acpi_button0: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
ACPI: Found matching pin for 0.7.INTD at func 2: 11
ACPI: Found matching pin for 0.2.INTA at func 0: 11
ACPI: Found matching pin for 0.2.INTB at func 1: 11
ACPI: Found matching pin for 0.3.INTA at func 0: 11
ACPI: Found matching pin for 0.6.INTA at func 0: 11
pci0: <ACPI PCI bus> on pcib0
pci0: domain=0, physical bus=0
found-> vendor=0x8086, dev=0x7190, revid=0x03
domain=0, bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0xa210, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type Prefetchable Memory, range 32, base 0x40000000, size 26, enabled
found-> vendor=0x8086, dev=0x7191, revid=0x03
domain=0, bus=0, slot=1, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0007, statreg=0x0220, cachelnsz=0 (dwords)
lattimer=0xa8 (5040 ns), mingnt=0x88 (34000 ns), maxlat=0x00 (0 ns)
found-> vendor=0x104c, dev=0xac1b, revid=0x03
domain=0, bus=0, slot=2, func=0
class=06-07-00, hdrtype=0x02, mfdev=1
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0xa8 (5040 ns), mingnt=0xc0 (48000 ns), maxlat=0x03 (750 ns)
intpin=a, irq=11
powerspec 1 supports D0 D1 D2 D3 current D0
map[10]: type Memory, range 32, base 0x50103000, size 12, enabled
pcib0: matched entry for 0.2.INTA (src \\_SB_.LNKA:0)
pcib0: slot 2 INTA routed to irq 11 via \\_SB_.LNKA
found-> vendor=0x104c, dev=0xac1b, revid=0x03
domain=0, bus=0, slot=2, func=1
class=06-07-00, hdrtype=0x02, mfdev=1
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0xa8 (5040 ns), mingnt=0xc0 (48000 ns), maxlat=0x03 (750 ns)
intpin=b, irq=11
powerspec 1 supports D0 D1 D2 D3 current D0
map[10]: type Memory, range 32, base 0x50102000, size 12, enabled
pcib0: matched entry for 0.2.INTB (src \\_SB_.LNKB:0)
pcib0: slot 2 INTB routed to irq 11 via \\_SB_.LNKB
found-> vendor=0x11c1, dev=0x0449, revid=0x01
domain=0, bus=0, slot=3, func=0
class=07-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0107, statreg=0x8290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0xfc (63000 ns), maxlat=0x0e (3500 ns)
intpin=a, irq=11
powerspec 2 supports D0 D2 D3 current D0
map[10]: type Memory, range 32, base 0x50101000, size 8, enabled
map[14]: type I/O Port, range 32, base 0x4500, size 3, enabled
map[18]: type I/O Port, range 32, base 0x4400, size 8, enabled
pcib0: matched entry for 0.3.INTA (src \\_SB_.LNKC:0)
pcib0: slot 3 INTA routed to irq 11 via \\_SB_.LNKC
found-> vendor=0x1013, dev=0x6003, revid=0x01
domain=0, bus=0, slot=6, func=0
class=04-01-00, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0410, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x04 (1000 ns), maxlat=0x18 (6000 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type Memory, range 32, base 0x50100000, size 12, enabled
map[14]: type Memory, range 32, base 0x50000000, size 20, enabled
pcib0: matched entry for 0.6.INTA (src \\_SB_.LNKA:0)
pcib0: slot 6 INTA routed to irq 11 via \\_SB_.LNKA
found-> vendor=0x8086, dev=0x7110, revid=0x02
domain=0, bus=0, slot=7, func=0
class=06-80-00, hdrtype=0x00, mfdev=1
cmdreg=0x000f, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x7111, revid=0x01
domain=0, bus=0, slot=7, func=1
class=01-01-80, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x30 (1440 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[20]: type I/O Port, range 32, base 0xfcf0, size 4, enabled
found-> vendor=0x8086, dev=0x7112, revid=0x01
domain=0, bus=0, slot=7, func=2
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x30 (1440 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=d, irq=11
map[20]: type I/O Port, range 32, base 0x4000, size 5, enabled
pcib0: matched entry for 0.7.INTD (src \\_SB_.LNKD:0)
pcib0: slot 7 INTD routed to irq 11 via \\_SB_.LNKD
found-> vendor=0x8086, dev=0x7113, revid=0x03
domain=0, bus=0, slot=7, func=3
class=06-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0003, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[90]: type I/O Port, range 32, base 0xefa0, size 4, enabled
agp0: <Intel 82443BX (440 BX) host to PCI bridge> on hostb0
hostb0: Reserved 0x4000000 bytes for rid 0x10 type 3 at 0x40000000
agp0: allocating GATT for aperture of size 64M
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pcib1: domain 0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xd000-0xdfff
pcib1: memory decode 0x70000000-0xdfffffff
pcib1: prefetched decode 0xe0000000-0xf7ffffff
ACPI: Found matching pin for 1.0.INTA at func 0: 11
pci1: <ACPI PCI bus> on pcib1
pci1: domain=0, physical bus=1
found-> vendor=0x10c8, dev=0x0006, revid=0x00
domain=0, bus=1, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x80 (3840 ns), mingnt=0x10 (4000 ns), maxlat=0xff (63750 ns)
intpin=a, irq=11
powerspec 1 supports D0 D1 D2 D3 current D0
map[10]: type Prefetchable Memory, range 32, base 0xe0000000, size 25, enabled
pcib1: requested memory range 0xe0000000-0xe1ffffff: good
map[14]: type Memory, range 32, base 0x70000000, size 22, enabled
pcib1: requested memory range 0x70000000-0x703fffff: good
map[18]: type Memory, range 32, base 0x70400000, size 20, enabled
pcib1: requested memory range 0x70400000-0x704fffff: good
pcib1: matched entry for 1.0.INTA (src \\_SB_.LNKA:0)
pcib1: slot 0 INTA routed to irq 11 via \\_SB_.LNKA
vgapci0: <VGA-compatible display> mem 0xe0000000-0xe1ffffff,0x70000000-0x703fffff,0x70400000-0x704fffff irq 11 at device 0.0 on pci1
cbb0: <TI1450 PCI-CardBus Bridge> mem 0x50103000-0x50103fff irq 11 at device 2.0 on pci0
cbb0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0x50103000
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
cbb0: [MPSAFE]
cbb0: [FILTER]
cbb0: PCI Configuration space:
0x00: 0xac1b104c 0x02100007 0x06070003 0x0082a808
0x10: 0x50103000 0x020000a0 0xb0040200 0xfffff000
0x20: 0x00000000 0xfffff000 0x00000000 0x0000fffc
0x30: 0x00000000 0x0000fffc 0x00000000 0x0740010b
0x40: 0x01301014 0x00000001 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00449069 0x00000000 0x80818080 0x00001000
0x90: 0x416602c0 0x00000000 0x00000000 0x00000000
0xa0: 0x7e110001 0x00c00000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
cbb1: <TI1450 PCI-CardBus Bridge> mem 0x50102000-0x50102fff irq 11 at device 2.1 on pci0
cbb1: Reserved 0x1000 bytes for rid 0x10 type 3 at 0x50102000
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1
cbb1: [MPSAFE]
cbb1: [FILTER]
cbb1: PCI Configuration space:
0x00: 0xac1b104c 0x02100007 0x06070003 0x0082a808
0x10: 0x50102000 0x020000a0 0xb0070500 0xfffff000
0x20: 0x00000000 0xfffff000 0x00000000 0x0000fffc
0x30: 0x00000000 0x0000fffc 0x00000000 0x0740020b
0x40: 0x01301014 0x00000001 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x0044b069 0x00000000 0x80818080 0x00001000
0x90: 0x416602c0 0x00000000 0x00000000 0x00000000
0xa0: 0x7e110001 0x00c00000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
pci0: <simple comms> at device 3.0 (no driver attached)
csa0: <CS4280/CS4614/CS4622/CS4624/CS4630> mem 0x50100000-0x50100fff,0x50000000-0x500fffff irq 11 at device 6.0 on pci0
csa: card is Thinkpad 600X/A20/T20
csa0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0x50100000
csa0: Reserved 0x100000 bytes for rid 0x14 type 3 at 0x50000000
csa0: [GIANT-LOCKED]
csa0: [ITHREAD]
pcm0: <CS461x PCM Audio> on csa0
pcm0: <Cirrus Logic CS4297A AC97 Codec (id = 0x43525913)>
pcm0: Codec features headphone, 20 bit DAC, 18 bit ADC, 6 bit master volume, Crystal Semi 3D Stereo Enhancement
pcm0: Primary codec extended features AMAP
pcm0: ac97 codec dac ready count: 0
pcm0: Mixer "vol":
pcm0: Mixer "pcm":
pcm0: Mixer "speaker":
pcm0: Mixer "line":
pcm0: Mixer "mic":
pcm0: Mixer "cd":
pcm0: Mixer "rec":
pcm0: Mixer "igain":
pcm0: Mixer "ogain":
pcm0: Mixer "line1":
pcm0: Mixer "phin":
pcm0: Mixer "phout":
pcm0: Mixer "video":
pcm0: [GIANT-LOCKED]
pcm0: [ITHREAD]
pcm0: clone manager: deadline=750ms flags=0x8000001e
pcm0: sndbuf_setmap f813000, 1000; 0xc1fed000 -> f813000
pcm0: sndbuf_setmap f814000, 1000; 0xc1fee000 -> f814000
PCI-ISA bridge with incorrect subclass 0x80
PCI-ISA bridge with incorrect subclass 0x80
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 UDMA33 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfcf0-0xfcff at device 7.1 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xfcf0
ata0: <ATA channel 0> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=50 stat1=00 devices=0x1
ata0: [MPSAFE]
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=03 ostat0=51 ostat1=00
ata1: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: stat1=0x00 err=0x04 lsb=0x7f msb=0x7f
ata1: reset tp2 stat0=00 stat1=00 devices=0x10000
ata1: [MPSAFE]
ata1: [ITHREAD]
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0x4000-0x401f irq 11 at device 7.2 on pci0
uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0x4000
uhci0: [GIANT-LOCKED]
uhci0: [ITHREAD]
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 2 ports with 2 removable, self powered
pci0: <bridge> at device 7.3 (no driver attached)
acpi_tz0: <Thermal Zone> on acpi0
acpi_tz1: <Thermal Zone> on acpi0
acpi_tz2: <Thermal Zone> on acpi0
acpi_tz3: <Thermal Zone> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0045
atkbd: keyboard ID 0x54ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: unable to allocate IRQ
psmcpnp0: <PS/2 mouse port> irq 12 on acpi0
psm0: current command byte:0045
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons
psm0: config:00000000, flags:00000008, packet size:3
psm0: syncmask:c0, syncbits:00
atrtc0: <AT realtime clock> port 0x70-0x73 irq 8 on acpi0
atrtc0: registered as a time-of-day clock (resolution 1000000us)
battery0: <ACPI Control Method Battery> on acpi0
acpi_acad0: <AC Adapter> on acpi0
cpu0: <ACPI CPU> on acpi0
cpu0: switching to generic Cx mode
acpi_throttle0: <ACPI CPU Throttling> on cpu0
acpi_throttle0: P_CNT from P_BLK 0xef10
ex_isa_identify()
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
isa_probe_children: disabling PnP devices
pmtimer0 on isa0
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
atrtc: atrtc0 already exists; skipping it
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: probing non-PnP devices
orm0: <ISA Option ROM> at iomem 0xc0000-0xcbfff pnpid ORM0000 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd1, terminal emulator: sc (syscons terminal)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fdc0 failed to probe at port 0x3f0 irq 6 drq 2 on isa0
fe0: not probed (disabled)
ie0: not probed (disabled)
le0: not probed (disabled)
ppc0: parallel port found at 0x3bc
ppc0: cannot reserve I/O port range
ppc0: <Parallel port> failed to probe at port 0x3bc-0x3c3 irq 7 on isa0
sn0: not probed (disabled)
uart0: <16550 or compatible> at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
uart0: [FILTER]
uart0: fast interrupt
uart1: <ns8250> failed to probe at port 0x2f8-0x2ff irq 3 on isa0
uart2: not probed (disabled)
uart3: not probed (disabled)
isa_probe_children: probing PnP devices
Device configuration finished.
procfs registered
Timecounter "TSC" frequency 498274309 Hz quality 800
Timecounters tick every 1.000 msec
ipfw2 initialized, divert loadable, nat loadable, rule-based forwarding enabled, default to accept, logging limited to 100 packets/entry by default
lo0: bpf attached
ata0: identify ch->devices=00000001
battery0: battery initialization start
acpi_acad0: acline initialization start
system power profile changed to 'economy'
acpi_acad0: Off Line
acpi_acad0: acline initialization done, tried 1 times
ata0-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=80 wire
ad0: setting Pacpi_tz1: _AC0: temperature 43.8 >= setpoint 33.5
IO4 on PIIX4 chipacpi_tz1: switched from NONE to _AC0: 43.8C
ad0: setting UDMA33 on PIIX4 chip
ad0: 57231MB <WDC WD600VE-07HDT0 09.07D09> at ata0-master UDMA33
ad0: 117210240 sectors [124032C/15H/63S] 16 sectors/interrupt 1 depth queue
ata1: identify ch->devices=00010000
GEOM: new disk ad0
map[10]: type I/O Port, range 32, base 0, size 6, port disabled
found-> vendor=0x10b7, dev=0x5057, revid=0x00
domain=0, bus=5, slot=0, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0000, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x08 (2000 ns)
intpin=a, irq=11
xl0: <3Com 3c575TX Fast Etherlink XL> port 0x1000-0x103f irq 11 at device 0.0 on cardbus1
xl0: Reserved 0x40 bytes for rid 0x10 type 4 at 0x1000
cbb1: Opening I/O: 0x1000-0x103f
xl0: using port I/O
xl0: media options word: 40
xl0: found MII/AUTO
miibus0: <MII bus> on xl0
tdkphy0: <TDK 78Q2120 media interface> PHY 0 on miibus0
tdkphy0: OUI 0x00c039, model 0x0014, rev. 3
tdkphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl0: bpf attached
xl0: Ethernet address: 00:60:08:d2:38:56
xl0: [MPSAFE]
xl0: [ITHREAD]
ata1-master: pio=PIO4 wdma=WDMA2 udma=UNSUPPORTED cable=40 wire
battery0: battery initialization done, tried 1 times
Need to ack 0x1
acd0: setting PIO4 on PIIX4 chip
acd0: <TOSHIBA CD-ROM XM-1902B/1717> CDROM drive at ata1 as master
acd0: read 4134KB/s (4134KB/s), 128KB buffer, PIO4
acd0: Reads: CDR, CDRW, CDDA stream
acd0: Writes:
acd0: Audio: play, 16 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
Trying to mount root from ufs:/dev/ad0s2a
ct_to_ts([2008-12-09 21:42:31]) = 1228858951.000000000
start_init: trying /sbin/init
WARNING: attempt to net_add_domain(bluetooth) after domainfinalize()
splash: image decoder found: snake_saver
xl0: reset didn't complete
xl0: command never completed!
xl0: command never completed!
xl0: command never completed!
tdkphy0: detached
miibus0: detached
xl0: detached
Need to ack 0x1
map[10]: type I/O Port, range 32, base 0, size 6, port disabled
found-> vendor=0x10b7, dev=0x5057, revid=0x00
domain=0, bus=5, slot=0, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0000, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x08 (2000 ns)
intpin=a, irq=11
xl0: <3Com 3c575TX Fast Etherlink XL> port 0x1000-0x103f irq 11 at device 0.0 on cardbus1
xl0: Reserved 0x40 bytes for rid 0x10 type 4 at 0x1000
cbb1: Opening I/O: 0x1000-0x103f
xl0: using port I/O
xl0: media options word: 40
xl0: found MII/AUTO
miibus0: <MII bus> on xl0
tdkphy0: <TDK 78Q2120 media interface> PHY 0 on miibus0
tdkphy0: OUI 0x00c039, model 0x0014, rev. 3
tdkphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl0: bpf attached
xl0: Ethernet address: 00:60:08:d2:38:56
xl0: [MPSAFE]
xl0: [ITHREAD]
xl0: link state changed to DOWN
system power profile changed to 'performance'
acpi_acad0: On Line
xl0: link state changed to UP
More information about the freebsd-current
mailing list