cvs commit: src/sys/dev/bce if_bce.c src/sys/dev/em if_em.c
if_em.h src/sys/dev/mpt mpt.h mpt_pci.c
Jia-Shiun Li
jiashiun at gmail.com
Wed Nov 22 06:07:43 PST 2006
My em0 stops working a few seconds after booting. And there are
watchdog timeout messages.
I tried kldunload it (I load it as module in loader.conf) and reload.
Pinging other hosts get only the first few ~10 replies. Adding
hw.pci.enable_msi[x]=0 to loader.conf solves this problem.
dmesg output before and after disabling msi are attached. The only
difference meaningful to me is the irq vector assignment from PCI IRQ
96 to MSI IRQ 256. Not sure if this is a bug in MSI or buggy ACPI
bios.
BTW when I kldunload if_em, something (devd?) automatically reload it
again immediately. How to stop this behavior?
Jia-Shiun.
-------------- next part --------------
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.0-CURRENT #0: Wed Nov 22 15:46:21 CST 2006
jsli at jsli-x4:/usr/obj/usr/src/sys/x4
Using 16 colors for the VM-PQ tuning (512, 8)
Preloaded elf kernel "/boot/kernel/kernel" at 0xc086f000.
Preloaded elf module "/boot/kernel/if_em.ko" at 0xc086f188.
Preloaded elf module "/boot/kernel/snd_es137x.ko" at 0xc086f234.
Preloaded elf module "/boot/kernel/sound.ko" at 0xc086f2e4.
Preloaded elf module "/boot/kernel/ums.ko" at 0xc086f390.
Preloaded elf module "/boot/kernel/usb.ko" at 0xc086f438.
Preloaded elf module "/boot/kernel/green_saver.ko" at 0xc086f4e0.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc086f590.
MP Configuration Table version 1.4 found at 0xc00fa2c0
Table 'FACP' at 0x1fff0200
Table 'APIC' at 0x1fff0300
MADT: Found table at 0x1fff0300
APIC: Using the MADT enumerator.
MADT: Found CPU APIC ID 0 ACPI ID 1: enabled
SMP: Added CPU 0 (AP)
MADT: Found CPU APIC ID 6 ACPI ID 2: enabled
SMP: Added CPU 6 (AP)
MADT: Found CPU APIC ID 130 ACPI ID 3: disabled
MADT: Found CPU APIC ID 131 ACPI ID 4: disabled
INTR: Adding local APIC 0 as a target
ACPI APIC Table: <A M I OEMAPIC >
Calibrating clock(s) ... i8254 clock: 1193146 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 1999785128 Hz
CPU: Intel(R) XEON(TM) CPU 2.00GHz (1999.79-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf24 Stepping = 4
Features=0x3febfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM>
Instruction TLB: 4 KB, 2 MB or 4 MB pages, fully associative, 64 entries
Data TLB: 4 KB or 4 MB pages, fully associative, 64 entries
1st-level data cache: 8 KB, 4-way set associative, sectored cache, 64 byte line size
Trace cache: 12K-uops, 8-way set associative
2nd-level cache: 512 KB, 8-way set associative, sectored cache, 64 byte line size
real memory = 536805376 (511 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000c28000 - 0x000000001f659fff, 514007040 bytes (125490 pages)
avail memory = 515289088 (491 MB)
INTR: Adding local APIC 6 as a target
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 6
bios32: Found BIOS32 Service Directory header at 0xc00f0000
bios32: Entry = 0xf0010 (c00f0010) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0x31
pnpbios: Found PnP BIOS data at 0xc00f4610
pnpbios: Entry = f0000:4daa Rev = 1.0
Other BIOS signatures found:
APIC: CPU 0 has ACPI ID 1
APIC: CPU 1 has ACPI ID 2
MADT: Found IO APIC ID 7, Interrupt 0 at 0xfec00000
ioapic0: Routing external 8259A's -> intpin 0
MADT: Found IO APIC ID 8, Interrupt 24 at 0xfec80000
MADT: Found IO APIC ID 9, Interrupt 48 at 0xfec80400
MADT: Found IO APIC ID 10, Interrupt 72 at 0xfec82000
MADT: Found IO APIC ID 11, Interrupt 96 at 0xfec82400
MADT: Found IO APIC ID 12, Interrupt 120 at 0xfec81000
MADT: Found IO APIC ID 13, Interrupt 144 at 0xfec81400
MADT: Interrupt override: source 0, irq 2
ioapic0: Routing IRQ 0 -> intpin 2
MADT: Interrupt override: source 9, irq 9
ioapic0: intpin 9 trigger: level
ioapic0 <Version 2.0> irqs 0-23 on motherboard
ioapic1 <Version 2.0> irqs 24-47 on motherboard
ioapic2 <Version 2.0> irqs 48-71 on motherboard
ioapic3 <Version 2.0> irqs 72-95 on motherboard
ioapic4 <Version 2.0> irqs 96-119 on motherboard
cpu0 BSP:
ID: 0x00000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000100ef therm: 0x00010000 err: 0x0001000f pcm: 0x00010000
random: <entropy source, Software, Yarrow>
io: <I/O>
kbd: new array size 4
kbd1 at kbdmux0
nfslock: pseudo-device
mem: <memory>
Pentium Pro MTRR support enabled
null: <null device, zero device>
npx0: INT 16 interface
acpi0: <A M I OEMXSDT> on motherboard
ioapic0: routing intpin 9 (ISA IRQ 9) to vector 48
acpi0: [MPSAFE]
pci_open(1): mode 1 addr port (0x0cf8) is 0x8000005c
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=25408086)
pcibios: BIOS version 2.10
AcpiOsDerivePciId: bus 0 dev 31 func 0
acpi0: Power Button (fixed)
acpi0: wakeup code va 0xcce2a000 pa 0x9e000
AcpiOsDerivePciId: bus 0 dev 31 func 0
ACPI timer: 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 -> 10
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
pci_link0: Index IRQ Rtd Ref IRQs
Initial Probe 0 11 N 0 3 4 5 6 7 9 10 11 12 14 15
Validation 0 11 N 0 3 4 5 6 7 9 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link1: Index IRQ Rtd Ref IRQs
Initial Probe 0 9 N 0 3 4 5 6 7 9 10 11 12 14 15
Validation 0 9 N 0 3 4 5 6 7 9 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link2: Index IRQ Rtd Ref IRQs
Initial Probe 0 10 N 0 3 4 5 6 7 9 10 11 12 14 15
Validation 0 10 N 0 3 4 5 6 7 9 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link3: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
Validation 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link4: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
Validation 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link5: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
Validation 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link6: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
Validation 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link7: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
Validation 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
cpu0: <ACPI CPU> on acpi0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
acpi_throttle0: P_CNT from P_BLK 0x410
cpu1: <ACPI CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
found-> vendor=0x8086, dev=0x2540, revid=0x02
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0080, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x2543, revid=0x02
bus=0, slot=2, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x00a0, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x06 (1500 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x2547, revid=0x02
bus=0, slot=4, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x00a0, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x06 (1500 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x2482, revid=0x02
bus=0, slot=29, func=0
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
map[20]: type 4, range 32, base 0xec00, size 5, enabled
pcib0: matched entry for 0.29.INTA
pcib0: slot 29 INTA hardwired to IRQ 16
found-> vendor=0x8086, dev=0x244e, revid=0x42
bus=0, slot=30, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x0080, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x0a (2500 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x2480, revid=0x02
bus=0, slot=31, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x000f, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x248b, revid=0x02
bus=0, slot=31, func=1
class=01-01-8a, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=255
map[20]: type 4, range 32, base 0xffa0, size 4, enabled
map[24]: type 1, range 32, base 0, size 10, memory disabled
found-> vendor=0x8086, dev=0x2483, revid=0x02
bus=0, slot=31, func=3
class=0c-05-00, hdrtype=0x00, mfdev=0
cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=255
map[20]: type 4, range 32, base 0x540, size 5, enabled
pcib1: <ACPI PCI-PCI bridge> at device 2.0 on pci0
pcib1: secondary bus 5
pcib1: subordinate bus 7
pcib1: I/O decode 0xc000-0xdfff
pcib1: memory decode 0xfe600000-0xfeafffff
pcib1: prefetched decode 0xff700000-0xff9fffff
pcib1: could not get PCI interrupt routing table for \\_SB_.PCI0.P0P8 - AE_NOT_FOUND
pci5: <ACPI PCI bus> on pcib1
pci5: physical bus=5
found-> vendor=0x8086, dev=0x1461, revid=0x03
bus=5, slot=28, func=0
class=08-00-20, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0030, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 1, range 32, base 0xfeafe000, size 12, enabled
pcib1: requested memory range 0xfeafe000-0xfeafefff: good
found-> vendor=0x8086, dev=0x1460, revid=0x03
bus=5, slot=29, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0106, statreg=0x0030, cachelnsz=16 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x06 (1500 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x1461, revid=0x03
bus=5, slot=30, func=0
class=08-00-20, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0030, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 1, range 32, base 0xfeaff000, size 12, enabled
pcib1: requested memory range 0xfeaff000-0xfeafffff: good
found-> vendor=0x8086, dev=0x1460, revid=0x03
bus=5, slot=31, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x0030, cachelnsz=16 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x06 (1500 ns), maxlat=0x00 (0 ns)
pci5: <base peripheral, interrupt controller> at device 28.0 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> at device 29.0 on pci5
pcib2: secondary bus 7
pcib2: subordinate bus 7
pcib2: I/O decode 0x0-0x0
pcib2: memory decode 0xfe900000-0xfe9fffff
pcib2: prefetched decode 0xff800000-0xff8fffff
pci7: <ACPI PCI bus> on pcib2
pci7: physical bus=7
found-> vendor=0x8086, dev=0x1462, revid=0x03
bus=7, slot=31, func=0
class=08-04-00, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0230, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=9
map[10]: type 3, range 64, base 0xff8ffc00, size 8, enabled
pcib2: requested memory range 0xff8ffc00-0xff8ffcff: good
pcib1: requested memory range 0xff8ffc00-0xff8ffcff: good
pcib2: matched entry for 7.31.INTA
pcib2: slot 31 INTA hardwired to IRQ 71
pci7: <base peripheral, PCI hot-plug controller> at device 31.0 (no driver attached)
pci5: <base peripheral, interrupt controller> at device 30.0 (no driver attached)
pcib3: <ACPI PCI-PCI bridge> at device 31.0 on pci5
pcib3: secondary bus 6
pcib3: subordinate bus 6
pcib3: I/O decode 0xc000-0xdfff
pcib3: memory decode 0xfe600000-0xfe8fffff
pcib3: prefetched decode 0xff700000-0xff7fffff
pci6: <ACPI PCI bus> on pcib3
pci6: physical bus=6
found-> vendor=0x9005, dev=0x801f, revid=0x02
bus=6, slot=1, func=0
class=01-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0230, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x28 (10000 ns), maxlat=0x19 (6250 ns)
intpin=a, irq=255
powerspec 2 supports D0 D3 current D0
MSI supports 2 messages, 64 bit
map[10]: type 4, range 32, base 0xffffff00, size 8, port disabled
map[1c]: type 4, range 32, base 0xffffff00, size 8, port disabled
found-> vendor=0x9005, dev=0x801f, revid=0x02
bus=6, slot=1, func=1
class=01-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0230, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x28 (10000 ns), maxlat=0x19 (6250 ns)
intpin=b, irq=255
powerspec 2 supports D0 D3 current D0
MSI supports 2 messages, 64 bit
map[10]: type 4, range 32, base 0xffffff00, size 8, port disabled
map[1c]: type 4, range 32, base 0xffffff00, size 8, port disabled
pci6: <mass storage, SCSI> at device 1.0 (no driver attached)
pci6: <mass storage, SCSI> at device 1.1 (no driver attached)
pcib4: <ACPI PCI-PCI bridge> at device 4.0 on pci0
pcib4: secondary bus 2
pcib4: subordinate bus 4
pcib4: I/O decode 0xb000-0xbfff
pcib4: memory decode 0xfe300000-0xfe5fffff
pcib4: prefetched decode 0xff400000-0xff6fffff
pcib4: could not get PCI interrupt routing table for \\_SB_.PCI0.P0P2 - AE_NOT_FOUND
pci2: <ACPI PCI bus> on pcib4
pci2: physical bus=2
found-> vendor=0x8086, dev=0x1461, revid=0x03
bus=2, slot=28, func=0
class=08-00-20, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0030, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 1, range 32, base 0xfe5fe000, size 12, enabled
pcib4: requested memory range 0xfe5fe000-0xfe5fefff: good
found-> vendor=0x8086, dev=0x1460, revid=0x03
bus=2, slot=29, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x0030, cachelnsz=16 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x06 (1500 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x1461, revid=0x03
bus=2, slot=30, func=0
class=08-00-20, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0030, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 1, range 32, base 0xfe5ff000, size 12, enabled
pcib4: requested memory range 0xfe5ff000-0xfe5fffff: good
found-> vendor=0x8086, dev=0x1460, revid=0x03
bus=2, slot=31, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0106, statreg=0x0030, cachelnsz=16 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x06 (1500 ns), maxlat=0x00 (0 ns)
pci2: <base peripheral, interrupt controller> at device 28.0 (no driver attached)
pcib5: <ACPI PCI-PCI bridge> at device 29.0 on pci2
pcib5: secondary bus 4
pcib5: subordinate bus 4
pcib5: I/O decode 0xb000-0xbfff
pcib5: memory decode 0xfe400000-0xfe4fffff
pcib5: prefetched decode 0xff500000-0xff5fffff
pci4: <ACPI PCI bus> on pcib5
pci4: physical bus=4
found-> vendor=0x8086, dev=0x1008, revid=0x02
bus=4, slot=1, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0117, statreg=0x0230, cachelnsz=16 (dwords)
lattimer=0x40 (1920 ns), mingnt=0xff (63750 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D3 current D0
MSI supports 1 message, 64 bit
map[10]: type 1, range 64, base 0xfe4e0000, size 17, enabled
pcib5: requested memory range 0xfe4e0000-0xfe4fffff: good
pcib4: requested memory range 0xfe4e0000-0xfe4fffff: good
map[18]: type 1, range 64, base 0xfe4c0000, size 17, enabled
pcib5: requested memory range 0xfe4c0000-0xfe4dffff: good
pcib4: requested memory range 0xfe4c0000-0xfe4dffff: good
map[20]: type 4, range 32, base 0xbc00, size 5, enabled
pcib5: requested I/O range 0xbc00-0xbc1f: in range
pcib4: requested I/O range 0xbc00-0xbc1f: in range
pcib5: matched entry for 4.1.INTA
pcib5: slot 1 INTA hardwired to IRQ 96
found-> vendor=0x8086, dev=0x1462, revid=0x03
bus=4, slot=31, func=0
class=08-04-00, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0230, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
map[10]: type 3, range 64, base 0xff5ffc00, size 8, enabled
pcib5: requested memory range 0xff5ffc00-0xff5ffcff: good
pcib4: requested memory range 0xff5ffc00-0xff5ffcff: good
pcib5: matched entry for 4.31.INTA
pcib5: slot 31 INTA hardwired to IRQ 119
em0: <Intel(R) PRO/1000 Network Connection Version - 6.2.9> port 0xbc00-0xbc1f mem 0xfe4e0000-0xfe4fffff,0xfe4c0000-0xfe4dffff irq 96 at device 1.0 on pci4
em0: Reserved 0x20000 bytes for rid 0x10 type 3 at 0xfe4e0000
em0: Reserved 0x20 bytes for rid 0x20 type 4 at 0xbc00
em0: bpf attached
em0: Ethernet address: 00:07:e9:03:58:09
em0: [FAST]
pci4: <base peripheral, PCI hot-plug controller> at device 31.0 (no driver attached)
pci2: <base peripheral, interrupt controller> at device 30.0 (no driver attached)
pcib6: <ACPI PCI-PCI bridge> at device 31.0 on pci2
pcib6: secondary bus 3
pcib6: subordinate bus 3
pcib6: I/O decode 0x0-0x0
pcib6: memory decode 0xfe300000-0xfe3fffff
pcib6: prefetched decode 0xff400000-0xff4fffff
pci3: <ACPI PCI bus> on pcib6
pci3: physical bus=3
found-> vendor=0x8086, dev=0x1462, revid=0x03
bus=3, slot=31, func=0
class=08-04-00, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0230, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
map[10]: type 3, range 64, base 0xff4ffc00, size 8, enabled
pcib6: requested memory range 0xff4ffc00-0xff4ffcff: good
pcib4: requested memory range 0xff4ffc00-0xff4ffcff: good
pcib6: matched entry for 3.31.INTA
pcib6: slot 31 INTA hardwired to IRQ 95
pci3: <base peripheral, PCI hot-plug controller> at device 31.0 (no driver attached)
uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port 0xec00-0xec1f irq 16 at device 29.0 on pci0
uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0xec00
ioapic0: routing intpin 16 (PCI IRQ 16) to vector 50
uhci0: [GIANT-LOCKED]
usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 2 ports with 2 removable, self powered
pcib7: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pcib7: secondary bus 1
pcib7: subordinate bus 1
pcib7: I/O decode 0xa000-0xafff
pcib7: memory decode 0xfc200000-0xfe2fffff
pcib7: prefetched decode 0xff300000-0xff3fffff
pcib7: Subtractively decoded bridge.
pci1: <ACPI PCI bus> on pcib7
pci1: physical bus=1
found-> vendor=0x102c, dev=0x00c0, revid=0x64
bus=1, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0183, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
map[10]: type 1, range 32, base 0xfd000000, size 24, enabled
pcib7: requested memory range 0xfd000000-0xfdffffff: good
pcib7: matched entry for 1.0.INTA
pcib7: slot 0 INTA hardwired to IRQ 16
found-> vendor=0x1274, dev=0x1371, revid=0x08
bus=1, slot=2, func=0
class=04-01-00, hdrtype=0x00, mfdev=0
cmdreg=0x0105, statreg=0x0410, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x0c (3000 ns), maxlat=0x80 (32000 ns)
intpin=a, irq=10
powerspec 1 supports D0 D2 D3 current D0
map[10]: type 4, range 32, base 0xac00, size 6, enabled
pcib7: requested I/O range 0xac00-0xac3f: in range
pcib7: matched entry for 1.2.INTA
pcib7: slot 2 INTA hardwired to IRQ 18
vgapci0: <VGA-compatible display> mem 0xfd000000-0xfdffffff irq 16 at device 0.0 on pci1
pcm0: <AudioPCI ES1373-8> port 0xac00-0xac3f irq 18 at device 2.0 on pci1
pcm0: Reserved 0x40 bytes for rid 0x10 type 4 at 0xac00
pcm0: <SigmaTel STAC9721/23 AC97 Codec (id = 0x83847609)>
pcm0: Codec features 18 bit DAC, 18 bit ADC, 5 bit master volume, SigmaTel 3D Enhancement
pcm0: Primary codec extended features AMAP
pcm0: ac97 codec dac ready count: 0
pcm0: Mixer "vol":
pcm0: Mixer "pcm":
pcm0: Mixer "speaker":
pcm0: Mixer "line":
pcm0: Mixer "mic":
pcm0: Mixer "cd":
pcm0: Mixer "rec":
pcm0: Mixer "igain":
pcm0: Mixer "ogain":
pcm0: Mixer "line1":
pcm0: Mixer "phin":
pcm0: Mixer "phout":
pcm0: Mixer "video":
ioapic0: routing intpin 18 (PCI IRQ 18) to vector 51
pcm0: [MPSAFE]
pcm0: sndbuf_setmap 223000, 1000; 0xc2af8000 -> 223000
pcm0: sndbuf_setmap 201000, 1000; 0xc2af6000 -> 201000
pcm0: sndbuf_setmap 22f000, 1000; 0xc2af4000 -> 22f000
pcm0: <Playback: DAC1,DAC2 / Record: ADC>
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH3 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 31.1 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xffa0
ata0: <ATA channel 0> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ioapic0: routing intpin 14 (ISA IRQ 14) to vector 52
ata0: [MPSAFE]
ata1: <ATA channel 1> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=03 ostat0=00 ostat1=00
ata1: stat0=0x01 err=0x01 lsb=0x01 msb=0x01
ata1: stat1=0x01 err=0x01 lsb=0x01 msb=0x01
ata1: reset tp2 stat0=01 stat1=01 devices=0x0
ioapic0: routing intpin 15 (ISA IRQ 15) to vector 53
ata1: [MPSAFE]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: irq maps: 0 0 0 0
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: irq maps: 0 0 0 0
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
ioapic0: routing intpin 4 (ISA IRQ 4) to vector 54
sio0: [FAST]
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0 0 0 0
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0 0 0 0
sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
ioapic0: routing intpin 3 (ISA IRQ 3) to vector 55
sio1: [FAST]
fdc0: <floppy drive controller (FDE)> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: ic_type 90 part_id 80
ioapic0: routing intpin 6 (ISA IRQ 6) to vector 56
fdc0: [MPSAFE]
fdc0: [FAST]
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
ioapic0: routing intpin 1 (ISA IRQ 1) to vector 57
atkbd0: [GIANT-LOCKED]
psm0: unable to allocate IRQ
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
fdc: fdc0 already exists; skipping it
sc: sc0 already exists; skipping it
sio: sio0 already exists; skipping it
sio: sio1 already exists; skipping it
vga: vga0 already exists; skipping it
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd1, terminal emulator: sc (syscons terminal)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
le0: not probed (disabled)
ppc0 failed to probe at irq 7 on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
ums0: <KYE Genius USB Wheel Mouse, class 0/0, rev 1.00/0.00, addr 2> on uhub0
ums0: 3 buttons and Z dir.
Device configuration finished.
procfs registered
lapic: Divisor 2, Frequency 49994644 hz
Timecounter "TSC" frequency 1999785128 Hz quality -100
Timecounters tick every 1.000 msec
splash: image decoder found: green_saver
lo0: bpf attached
ata0-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=80 wire
ad0: setting PIO4 on ICH3 chip
ad0: setting UDMA100 on ICH3 chip
ad0: 19092MB <WDC WD200BB-00CAA1 17.07W17> at ata0-master UDMA100
ad0: 39102336 sectors [38792C/16H/63S] 16 sectors/interrupt 1 depth queue
ad0: Intel check1 failed
ad0: Adaptec check1 failed
ad0: LSI (v3) check1 failed
ad0: LSI (v2) check1 failed
ad0: FreeBSD check1 failed
ATA PseudoRAID loaded
SMP: AP CPU #1 Launched!
cpu1 AP:
ID: 0x06000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000200ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010000
ioapic0: Assigning ISA IRQ 1 to local APIC 0
ioapic0: Assigning ISA IRQ 3 to local APIC 6
ioapic0: Assigning ISA IRQ 4 to local APIC 0
ioapic0: Assigning ISA IRQ 6 to local APIC 6
ioapic0: Assigning ISA IRQ 9 to local APIC 0
ioapic0: Assigning ISA IRQ 14 to local APIC 6
ioapic0: Assigning ISA IRQ 15 to local APIC 0
ioapic0: Assigning PCI IRQ 16 to local APIC 6
ioapic0: Assigning PCI IRQ 18 to local APIC 0
msi: Assigning MSI IRQ 256 to local APIC 6
GEOM: new disk ad0
Trying to mount root from ufs:/dev/ad0s1a
fdc0: output ready timeout
start_init: trying /sbin/init
fdc0: output ready timeout
fdc0: output ready timeout
fdc0: output ready timeout
fdc0: output ready timeout
fdc0: output ready timeout
fdc0: output ready timeout
fdc0: output ready timeout
fdc0: input ready timeout
fdc0: input ready timeout
fdc0: output ready timeout
fdc0: input ready timeout
fdc0: input ready timeout
fdc0: output ready timeout
fdc0: input ready timeout
fdc0: input ready timeout
fdc0: output ready timeout
fdc0: input ready timeout
fdc0: input ready timeout
em0: Link is up 100 Mbps Full Duplex
em0: link state changed to UP
em0: watchdog timeout -- resetting
em0: Link is Down
em0: link state changed to DOWN
em0: Link is up 100 Mbps Full Duplex
em0: link state changed to UP
em0: watchdog timeout -- resetting
em0: Link is Down
em0: link state changed to DOWN
em0: Link is up 100 Mbps Full Duplex
em0: link state changed to UP
em0: Link is Down
em0: link state changed to DOWN
em0: Link is up 100 Mbps Full Duplex
em0: link state changed to UP
em0: watchdog timeout -- resetting
em0: Link is Down
em0: link state changed to DOWN
em0: Link is up 100 Mbps Full Duplex
em0: link state changed to UP
em0: detached
pci0: driver added
found-> vendor=0x8086, dev=0x2483, revid=0x02
bus=0, slot=31, func=3
class=0c-05-00, hdrtype=0x00, mfdev=0
cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=255
pci0:31:3: reprobing on driver added
pci1: driver added
pci2: driver added
found-> vendor=0x8086, dev=0x1461, revid=0x03
bus=2, slot=28, func=0
class=08-00-20, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0030, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
pci2:28:0: reprobing on driver added
found-> vendor=0x8086, dev=0x1461, revid=0x03
bus=2, slot=30, func=0
class=08-00-20, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0030, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
pci2:30:0: reprobing on driver added
pci3: driver added
found-> vendor=0x8086, dev=0x1462, revid=0x03
bus=3, slot=31, func=0
class=08-04-00, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0230, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=95
pci3:31:0: reprobing on driver added
pci4: driver added
found-> vendor=0x8086, dev=0x1008, revid=0x02
bus=4, slot=1, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0117, statreg=0x0230, cachelnsz=16 (dwords)
lattimer=0x40 (1920 ns), mingnt=0xff (63750 ns), maxlat=0x00 (0 ns)
intpin=a, irq=96
powerspec 2 supports D0 D3 current D0
MSI supports 1 message, 64 bit
pci4:1:0: reprobing on driver added
em0: <Intel(R) PRO/1000 Network Connection Version - 6.2.9> port 0xbc00-0xbc1f mem 0xfe4e0000-0xfe4fffff,0xfe4c0000-0xfe4dffff irq 96 at device 1.0 on pci4
pcib5: em0 requested memory range 0xfe4e0000-0xfe4fffff: good
pcib4: em0 requested memory range 0xfe4e0000-0xfe4fffff: good
pcib5: em0 requested I/O range 0xbc00-0xbc1f: in range
pcib4: em0 requested I/O range 0xbc00-0xbc1f: in range
em0: bpf attached
em0: Ethernet address: 00:07:e9:03:58:09
msi: Assigning MSI IRQ 256 to local APIC 0
em0: [FAST]
found-> vendor=0x8086, dev=0x1462, revid=0x03
bus=4, slot=31, func=0
class=08-04-00, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0230, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=119
pci4:31:0: reprobing on driver added
pci5: driver added
found-> vendor=0x8086, dev=0x1461, revid=0x03
bus=5, slot=28, func=0
class=08-00-20, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0030, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
pci5:28:0: reprobing on driver added
found-> vendor=0x8086, dev=0x1461, revid=0x03
bus=5, slot=30, func=0
class=08-00-20, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0030, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
pci5:30:0: reprobing on driver added
pci6: driver added
found-> vendor=0x9005, dev=0x801f, revid=0x02
bus=6, slot=1, func=0
class=01-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0230, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x28 (10000 ns), maxlat=0x19 (6250 ns)
intpin=a, irq=255
powerspec 2 supports D0 D3 current D0
MSI supports 2 messages, 64 bit
pci6:1:0: reprobing on driver added
found-> vendor=0x9005, dev=0x801f, revid=0x02
bus=6, slot=1, func=1
class=01-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0230, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x28 (10000 ns), maxlat=0x19 (6250 ns)
intpin=b, irq=255
powerspec 2 supports D0 D3 current D0
MSI supports 2 messages, 64 bit
pci6:1:1: reprobing on driver added
pci7: driver added
found-> vendor=0x8086, dev=0x1462, revid=0x03
bus=7, slot=31, func=0
class=08-04-00, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0230, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=71
pci7:31:0: reprobing on driver added
em0: Link is up 100 Mbps Full Duplex
em0: link state changed to UP
em0: detached
pci0: driver added
found-> vendor=0x8086, dev=0x2483, revid=0x02
bus=0, slot=31, func=3
class=0c-05-00, hdrtype=0x00, mfdev=0
cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=255
pci0:31:3: reprobing on driver added
pci1: driver added
pci2: driver added
found-> vendor=0x8086, dev=0x1461, revid=0x03
bus=2, slot=28, func=0
class=08-00-20, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0030, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
pci2:28:0: reprobing on driver added
found-> vendor=0x8086, dev=0x1461, revid=0x03
bus=2, slot=30, func=0
class=08-00-20, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0030, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
pci2:30:0: reprobing on driver added
pci3: driver added
found-> vendor=0x8086, dev=0x1462, revid=0x03
bus=3, slot=31, func=0
class=08-04-00, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0230, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=95
pci3:31:0: reprobing on driver added
pci4: driver added
found-> vendor=0x8086, dev=0x1008, revid=0x02
bus=4, slot=1, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0117, statreg=0x0230, cachelnsz=16 (dwords)
lattimer=0x40 (1920 ns), mingnt=0xff (63750 ns), maxlat=0x00 (0 ns)
intpin=a, irq=96
powerspec 2 supports D0 D3 current D0
MSI supports 1 message, 64 bit
pci4:1:0: reprobing on driver added
em0: <Intel(R) PRO/1000 Network Connection Version - 6.2.9> port 0xbc00-0xbc1f mem 0xfe4e0000-0xfe4fffff,0xfe4c0000-0xfe4dffff irq 96 at device 1.0 on pci4
pcib5: em0 requested memory range 0xfe4e0000-0xfe4fffff: good
pcib4: em0 requested memory range 0xfe4e0000-0xfe4fffff: good
pcib5: em0 requested I/O range 0xbc00-0xbc1f: in range
pcib4: em0 requested I/O range 0xbc00-0xbc1f: in range
em0: bpf attached
em0: Ethernet address: 00:07:e9:03:58:09
msi: Assigning MSI IRQ 256 to local APIC 6
em0: [FAST]
found-> vendor=0x8086, dev=0x1462, revid=0x03
bus=4, slot=31, func=0
class=08-04-00, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0230, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=119
pci4:31:0: reprobing on driver added
pci5: driver added
found-> vendor=0x8086, dev=0x1461, revid=0x03
bus=5, slot=28, func=0
class=08-00-20, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0030, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
pci5:28:0: reprobing on driver added
found-> vendor=0x8086, dev=0x1461, revid=0x03
bus=5, slot=30, func=0
class=08-00-20, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0030, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
pci5:30:0: reprobing on driver added
pci6: driver added
found-> vendor=0x9005, dev=0x801f, revid=0x02
bus=6, slot=1, func=0
class=01-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0230, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x28 (10000 ns), maxlat=0x19 (6250 ns)
intpin=a, irq=255
powerspec 2 supports D0 D3 current D0
MSI supports 2 messages, 64 bit
pci6:1:0: reprobing on driver added
found-> vendor=0x9005, dev=0x801f, revid=0x02
bus=6, slot=1, func=1
class=01-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0230, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x28 (10000 ns), maxlat=0x19 (6250 ns)
intpin=b, irq=255
powerspec 2 supports D0 D3 current D0
MSI supports 2 messages, 64 bit
pci6:1:1: reprobing on driver added
pci7: driver added
found-> vendor=0x8086, dev=0x1462, revid=0x03
bus=7, slot=31, func=0
class=08-04-00, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0230, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=71
pci7:31:0: reprobing on driver added
em0: Link is up 100 Mbps Full Duplex
em0: link state changed to UP
em0: Link is Down
em0: link state changed to DOWN
em0: watchdog timeout -- resetting
em0: Link is up 100 Mbps Full Duplex
em0: link state changed to UP
em0: watchdog timeout -- resetting
em0: Link is Down
em0: link state changed to DOWN
em0: Link is up 100 Mbps Full Duplex
em0: link state changed to UP
Waiting (max 60 seconds) for system process `vnlru' to stop...done
Waiting (max 60 seconds) for system process `bufdaemon' to stop...done
Waiting (max 60 seconds) for system process `syncer' to stop...
Syncing disks, vnodes remaining...1 0 0 done
All buffers synced.
-------------- next part --------------
Copyright (c) 1992-2006 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.0-CURRENT #0: Wed Nov 22 15:46:21 CST 2006
jsli at jsli-x4:/usr/obj/usr/src/sys/x4
Using 16 colors for the VM-PQ tuning (512, 8)
Preloaded elf kernel "/boot/kernel/kernel" at 0xc086f000.
Preloaded elf module "/boot/kernel/if_em.ko" at 0xc086f188.
Preloaded elf module "/boot/kernel/snd_es137x.ko" at 0xc086f234.
Preloaded elf module "/boot/kernel/sound.ko" at 0xc086f2e4.
Preloaded elf module "/boot/kernel/ums.ko" at 0xc086f390.
Preloaded elf module "/boot/kernel/usb.ko" at 0xc086f438.
Preloaded elf module "/boot/kernel/green_saver.ko" at 0xc086f4e0.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc086f590.
MP Configuration Table version 1.4 found at 0xc00fa2c0
Table 'FACP' at 0x1fff0200
Table 'APIC' at 0x1fff0300
MADT: Found table at 0x1fff0300
APIC: Using the MADT enumerator.
MADT: Found CPU APIC ID 0 ACPI ID 1: enabled
SMP: Added CPU 0 (AP)
MADT: Found CPU APIC ID 6 ACPI ID 2: enabled
SMP: Added CPU 6 (AP)
MADT: Found CPU APIC ID 130 ACPI ID 3: disabled
MADT: Found CPU APIC ID 131 ACPI ID 4: disabled
INTR: Adding local APIC 0 as a target
ACPI APIC Table: <A M I OEMAPIC >
Calibrating clock(s) ... i8254 clock: 1193147 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 1999782196 Hz
CPU: Intel(R) XEON(TM) CPU 2.00GHz (1999.78-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0xf24 Stepping = 4
Features=0x3febfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM>
Instruction TLB: 4 KB, 2 MB or 4 MB pages, fully associative, 64 entries
Data TLB: 4 KB or 4 MB pages, fully associative, 64 entries
1st-level data cache: 8 KB, 4-way set associative, sectored cache, 64 byte line size
Trace cache: 12K-uops, 8-way set associative
2nd-level cache: 512 KB, 8-way set associative, sectored cache, 64 byte line size
real memory = 536805376 (511 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000c28000 - 0x000000001f659fff, 514007040 bytes (125490 pages)
avail memory = 515289088 (491 MB)
INTR: Adding local APIC 6 as a target
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 6
bios32: Found BIOS32 Service Directory header at 0xc00f0000
bios32: Entry = 0xf0010 (c00f0010) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0x31
pnpbios: Found PnP BIOS data at 0xc00f4610
pnpbios: Entry = f0000:4daa Rev = 1.0
Other BIOS signatures found:
APIC: CPU 0 has ACPI ID 1
APIC: CPU 1 has ACPI ID 2
MADT: Found IO APIC ID 7, Interrupt 0 at 0xfec00000
ioapic0: Routing external 8259A's -> intpin 0
MADT: Found IO APIC ID 8, Interrupt 24 at 0xfec80000
MADT: Found IO APIC ID 9, Interrupt 48 at 0xfec80400
MADT: Found IO APIC ID 10, Interrupt 72 at 0xfec82000
MADT: Found IO APIC ID 11, Interrupt 96 at 0xfec82400
MADT: Found IO APIC ID 12, Interrupt 120 at 0xfec81000
MADT: Found IO APIC ID 13, Interrupt 144 at 0xfec81400
MADT: Interrupt override: source 0, irq 2
ioapic0: Routing IRQ 0 -> intpin 2
MADT: Interrupt override: source 9, irq 9
ioapic0: intpin 9 trigger: level
ioapic0 <Version 2.0> irqs 0-23 on motherboard
ioapic1 <Version 2.0> irqs 24-47 on motherboard
ioapic2 <Version 2.0> irqs 48-71 on motherboard
ioapic3 <Version 2.0> irqs 72-95 on motherboard
ioapic4 <Version 2.0> irqs 96-119 on motherboard
cpu0 BSP:
ID: 0x00000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000100ef therm: 0x00010000 err: 0x0001000f pcm: 0x00010000
random: <entropy source, Software, Yarrow>
io: <I/O>
kbd: new array size 4
kbd1 at kbdmux0
nfslock: pseudo-device
mem: <memory>
Pentium Pro MTRR support enabled
null: <null device, zero device>
npx0: INT 16 interface
acpi0: <A M I OEMXSDT> on motherboard
ioapic0: routing intpin 9 (ISA IRQ 9) to vector 48
acpi0: [MPSAFE]
pci_open(1): mode 1 addr port (0x0cf8) is 0x8000005c
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=25408086)
pcibios: BIOS version 2.10
AcpiOsDerivePciId: bus 0 dev 31 func 0
acpi0: Power Button (fixed)
acpi0: wakeup code va 0xcce2a000 pa 0x9e000
AcpiOsDerivePciId: bus 0 dev 31 func 0
ACPI timer: 1/1 1/1 1/1 1/2 1/1 1/1 1/1 1/1 1/1 1/1 -> 10
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
pci_link0: Index IRQ Rtd Ref IRQs
Initial Probe 0 11 N 0 3 4 5 6 7 9 10 11 12 14 15
Validation 0 11 N 0 3 4 5 6 7 9 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link1: Index IRQ Rtd Ref IRQs
Initial Probe 0 9 N 0 3 4 5 6 7 9 10 11 12 14 15
Validation 0 9 N 0 3 4 5 6 7 9 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link2: Index IRQ Rtd Ref IRQs
Initial Probe 0 10 N 0 3 4 5 6 7 9 10 11 12 14 15
Validation 0 10 N 0 3 4 5 6 7 9 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link3: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
Validation 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link4: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
Validation 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link5: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
Validation 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link6: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
Validation 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
pci_link7: Index IRQ Rtd Ref IRQs
Initial Probe 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
Validation 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
After Disable 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15
cpu0: <ACPI CPU> on acpi0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
acpi_throttle0: P_CNT from P_BLK 0x410
cpu1: <ACPI CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
found-> vendor=0x8086, dev=0x2540, revid=0x02
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0080, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x2543, revid=0x02
bus=0, slot=2, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x00a0, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x06 (1500 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x2547, revid=0x02
bus=0, slot=4, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x00a0, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x06 (1500 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x2482, revid=0x02
bus=0, slot=29, func=0
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
map[20]: type 4, range 32, base 0xec00, size 5, enabled
pcib0: matched entry for 0.29.INTA
pcib0: slot 29 INTA hardwired to IRQ 16
found-> vendor=0x8086, dev=0x244e, revid=0x42
bus=0, slot=30, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x0080, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x0a (2500 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x2480, revid=0x02
bus=0, slot=31, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x000f, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x248b, revid=0x02
bus=0, slot=31, func=1
class=01-01-8a, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=255
map[20]: type 4, range 32, base 0xffa0, size 4, enabled
map[24]: type 1, range 32, base 0, size 10, memory disabled
found-> vendor=0x8086, dev=0x2483, revid=0x02
bus=0, slot=31, func=3
class=0c-05-00, hdrtype=0x00, mfdev=0
cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=255
map[20]: type 4, range 32, base 0x540, size 5, enabled
pcib1: <ACPI PCI-PCI bridge> at device 2.0 on pci0
pcib1: secondary bus 5
pcib1: subordinate bus 7
pcib1: I/O decode 0xc000-0xdfff
pcib1: memory decode 0xfe600000-0xfeafffff
pcib1: prefetched decode 0xff700000-0xff9fffff
pcib1: could not get PCI interrupt routing table for \\_SB_.PCI0.P0P8 - AE_NOT_FOUND
pci5: <ACPI PCI bus> on pcib1
pci5: physical bus=5
found-> vendor=0x8086, dev=0x1461, revid=0x03
bus=5, slot=28, func=0
class=08-00-20, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0030, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 1, range 32, base 0xfeafe000, size 12, enabled
pcib1: requested memory range 0xfeafe000-0xfeafefff: good
found-> vendor=0x8086, dev=0x1460, revid=0x03
bus=5, slot=29, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0106, statreg=0x0030, cachelnsz=16 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x06 (1500 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x1461, revid=0x03
bus=5, slot=30, func=0
class=08-00-20, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0030, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 1, range 32, base 0xfeaff000, size 12, enabled
pcib1: requested memory range 0xfeaff000-0xfeafffff: good
found-> vendor=0x8086, dev=0x1460, revid=0x03
bus=5, slot=31, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x0030, cachelnsz=16 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x06 (1500 ns), maxlat=0x00 (0 ns)
pci5: <base peripheral, interrupt controller> at device 28.0 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> at device 29.0 on pci5
pcib2: secondary bus 7
pcib2: subordinate bus 7
pcib2: I/O decode 0x0-0x0
pcib2: memory decode 0xfe900000-0xfe9fffff
pcib2: prefetched decode 0xff800000-0xff8fffff
pci7: <ACPI PCI bus> on pcib2
pci7: physical bus=7
found-> vendor=0x8086, dev=0x1462, revid=0x03
bus=7, slot=31, func=0
class=08-04-00, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0230, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=9
map[10]: type 3, range 64, base 0xff8ffc00, size 8, enabled
pcib2: requested memory range 0xff8ffc00-0xff8ffcff: good
pcib1: requested memory range 0xff8ffc00-0xff8ffcff: good
pcib2: matched entry for 7.31.INTA
pcib2: slot 31 INTA hardwired to IRQ 71
pci7: <base peripheral, PCI hot-plug controller> at device 31.0 (no driver attached)
pci5: <base peripheral, interrupt controller> at device 30.0 (no driver attached)
pcib3: <ACPI PCI-PCI bridge> at device 31.0 on pci5
pcib3: secondary bus 6
pcib3: subordinate bus 6
pcib3: I/O decode 0xc000-0xdfff
pcib3: memory decode 0xfe600000-0xfe8fffff
pcib3: prefetched decode 0xff700000-0xff7fffff
pci6: <ACPI PCI bus> on pcib3
pci6: physical bus=6
found-> vendor=0x9005, dev=0x801f, revid=0x02
bus=6, slot=1, func=0
class=01-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0230, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x28 (10000 ns), maxlat=0x19 (6250 ns)
intpin=a, irq=255
powerspec 2 supports D0 D3 current D0
MSI supports 2 messages, 64 bit
map[10]: type 4, range 32, base 0xffffff00, size 8, port disabled
map[1c]: type 4, range 32, base 0xffffff00, size 8, port disabled
found-> vendor=0x9005, dev=0x801f, revid=0x02
bus=6, slot=1, func=1
class=01-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0230, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x28 (10000 ns), maxlat=0x19 (6250 ns)
intpin=b, irq=255
powerspec 2 supports D0 D3 current D0
MSI supports 2 messages, 64 bit
map[10]: type 4, range 32, base 0xffffff00, size 8, port disabled
map[1c]: type 4, range 32, base 0xffffff00, size 8, port disabled
pci6: <mass storage, SCSI> at device 1.0 (no driver attached)
pci6: <mass storage, SCSI> at device 1.1 (no driver attached)
pcib4: <ACPI PCI-PCI bridge> at device 4.0 on pci0
pcib4: secondary bus 2
pcib4: subordinate bus 4
pcib4: I/O decode 0xb000-0xbfff
pcib4: memory decode 0xfe300000-0xfe5fffff
pcib4: prefetched decode 0xff400000-0xff6fffff
pcib4: could not get PCI interrupt routing table for \\_SB_.PCI0.P0P2 - AE_NOT_FOUND
pci2: <ACPI PCI bus> on pcib4
pci2: physical bus=2
found-> vendor=0x8086, dev=0x1461, revid=0x03
bus=2, slot=28, func=0
class=08-00-20, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0030, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 1, range 32, base 0xfe5fe000, size 12, enabled
pcib4: requested memory range 0xfe5fe000-0xfe5fefff: good
found-> vendor=0x8086, dev=0x1460, revid=0x03
bus=2, slot=29, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x0030, cachelnsz=16 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x06 (1500 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x1461, revid=0x03
bus=2, slot=30, func=0
class=08-00-20, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0030, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 1, range 32, base 0xfe5ff000, size 12, enabled
pcib4: requested memory range 0xfe5ff000-0xfe5fffff: good
found-> vendor=0x8086, dev=0x1460, revid=0x03
bus=2, slot=31, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0106, statreg=0x0030, cachelnsz=16 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x06 (1500 ns), maxlat=0x00 (0 ns)
pci2: <base peripheral, interrupt controller> at device 28.0 (no driver attached)
pcib5: <ACPI PCI-PCI bridge> at device 29.0 on pci2
pcib5: secondary bus 4
pcib5: subordinate bus 4
pcib5: I/O decode 0xb000-0xbfff
pcib5: memory decode 0xfe400000-0xfe4fffff
pcib5: prefetched decode 0xff500000-0xff5fffff
pci4: <ACPI PCI bus> on pcib5
pci4: physical bus=4
found-> vendor=0x8086, dev=0x1008, revid=0x02
bus=4, slot=1, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0117, statreg=0x0230, cachelnsz=16 (dwords)
lattimer=0x40 (1920 ns), mingnt=0xff (63750 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D3 current D0
MSI supports 1 message, 64 bit
map[10]: type 1, range 64, base 0xfe4e0000, size 17, enabled
pcib5: requested memory range 0xfe4e0000-0xfe4fffff: good
pcib4: requested memory range 0xfe4e0000-0xfe4fffff: good
map[18]: type 1, range 64, base 0xfe4c0000, size 17, enabled
pcib5: requested memory range 0xfe4c0000-0xfe4dffff: good
pcib4: requested memory range 0xfe4c0000-0xfe4dffff: good
map[20]: type 4, range 32, base 0xbc00, size 5, enabled
pcib5: requested I/O range 0xbc00-0xbc1f: in range
pcib4: requested I/O range 0xbc00-0xbc1f: in range
pcib5: matched entry for 4.1.INTA
pcib5: slot 1 INTA hardwired to IRQ 96
found-> vendor=0x8086, dev=0x1462, revid=0x03
bus=4, slot=31, func=0
class=08-04-00, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0230, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
map[10]: type 3, range 64, base 0xff5ffc00, size 8, enabled
pcib5: requested memory range 0xff5ffc00-0xff5ffcff: good
pcib4: requested memory range 0xff5ffc00-0xff5ffcff: good
pcib5: matched entry for 4.31.INTA
pcib5: slot 31 INTA hardwired to IRQ 119
em0: <Intel(R) PRO/1000 Network Connection Version - 6.2.9> port 0xbc00-0xbc1f mem 0xfe4e0000-0xfe4fffff,0xfe4c0000-0xfe4dffff irq 96 at device 1.0 on pci4
em0: Reserved 0x20000 bytes for rid 0x10 type 3 at 0xfe4e0000
em0: Reserved 0x20 bytes for rid 0x20 type 4 at 0xbc00
em0: bpf attached
em0: Ethernet address: 00:07:e9:03:58:09
ioapic4: routing intpin 0 (PCI IRQ 96) to vector 49
em0: [FAST]
pci4: <base peripheral, PCI hot-plug controller> at device 31.0 (no driver attached)
pci2: <base peripheral, interrupt controller> at device 30.0 (no driver attached)
pcib6: <ACPI PCI-PCI bridge> at device 31.0 on pci2
pcib6: secondary bus 3
pcib6: subordinate bus 3
pcib6: I/O decode 0x0-0x0
pcib6: memory decode 0xfe300000-0xfe3fffff
pcib6: prefetched decode 0xff400000-0xff4fffff
pci3: <ACPI PCI bus> on pcib6
pci3: physical bus=3
found-> vendor=0x8086, dev=0x1462, revid=0x03
bus=3, slot=31, func=0
class=08-04-00, hdrtype=0x00, mfdev=0
cmdreg=0x0106, statreg=0x0230, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
map[10]: type 3, range 64, base 0xff4ffc00, size 8, enabled
pcib6: requested memory range 0xff4ffc00-0xff4ffcff: good
pcib4: requested memory range 0xff4ffc00-0xff4ffcff: good
pcib6: matched entry for 3.31.INTA
pcib6: slot 31 INTA hardwired to IRQ 95
pci3: <base peripheral, PCI hot-plug controller> at device 31.0 (no driver attached)
uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port 0xec00-0xec1f irq 16 at device 29.0 on pci0
uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0xec00
ioapic0: routing intpin 16 (PCI IRQ 16) to vector 50
uhci0: [GIANT-LOCKED]
usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 2 ports with 2 removable, self powered
pcib7: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pcib7: secondary bus 1
pcib7: subordinate bus 1
pcib7: I/O decode 0xa000-0xafff
pcib7: memory decode 0xfc200000-0xfe2fffff
pcib7: prefetched decode 0xff300000-0xff3fffff
pcib7: Subtractively decoded bridge.
pci1: <ACPI PCI bus> on pcib7
pci1: physical bus=1
found-> vendor=0x102c, dev=0x00c0, revid=0x64
bus=1, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0183, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
map[10]: type 1, range 32, base 0xfd000000, size 24, enabled
pcib7: requested memory range 0xfd000000-0xfdffffff: good
pcib7: matched entry for 1.0.INTA
pcib7: slot 0 INTA hardwired to IRQ 16
found-> vendor=0x1274, dev=0x1371, revid=0x08
bus=1, slot=2, func=0
class=04-01-00, hdrtype=0x00, mfdev=0
cmdreg=0x0105, statreg=0x0410, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x0c (3000 ns), maxlat=0x80 (32000 ns)
intpin=a, irq=10
powerspec 1 supports D0 D2 D3 current D0
map[10]: type 4, range 32, base 0xac00, size 6, enabled
pcib7: requested I/O range 0xac00-0xac3f: in range
pcib7: matched entry for 1.2.INTA
pcib7: slot 2 INTA hardwired to IRQ 18
vgapci0: <VGA-compatible display> mem 0xfd000000-0xfdffffff irq 16 at device 0.0 on pci1
pcm0: <AudioPCI ES1373-8> port 0xac00-0xac3f irq 18 at device 2.0 on pci1
pcm0: Reserved 0x40 bytes for rid 0x10 type 4 at 0xac00
pcm0: <SigmaTel STAC9721/23 AC97 Codec (id = 0x83847609)>
pcm0: Codec features 18 bit DAC, 18 bit ADC, 5 bit master volume, SigmaTel 3D Enhancement
pcm0: Primary codec extended features AMAP
pcm0: ac97 codec dac ready count: 0
pcm0: Mixer "vol":
pcm0: Mixer "pcm":
pcm0: Mixer "speaker":
pcm0: Mixer "line":
pcm0: Mixer "mic":
pcm0: Mixer "cd":
pcm0: Mixer "rec":
pcm0: Mixer "igain":
pcm0: Mixer "ogain":
pcm0: Mixer "line1":
pcm0: Mixer "phin":
pcm0: Mixer "phout":
pcm0: Mixer "video":
ioapic0: routing intpin 18 (PCI IRQ 18) to vector 51
pcm0: [MPSAFE]
pcm0: sndbuf_setmap 223000, 1000; 0xc2af8000 -> 223000
pcm0: sndbuf_setmap 201000, 1000; 0xc2af6000 -> 201000
pcm0: sndbuf_setmap 22f000, 1000; 0xc2af4000 -> 22f000
pcm0: <Playback: DAC1,DAC2 / Record: ADC>
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH3 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 31.1 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xffa0
ata0: <ATA channel 0> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ioapic0: routing intpin 14 (ISA IRQ 14) to vector 52
ata0: [MPSAFE]
ata1: <ATA channel 1> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=03 ostat0=00 ostat1=00
ata1: stat0=0x01 err=0x01 lsb=0x01 msb=0x01
ata1: stat1=0x01 err=0x01 lsb=0x01 msb=0x01
ata1: reset tp2 stat0=01 stat1=01 devices=0x0
ioapic0: routing intpin 15 (ISA IRQ 15) to vector 53
ata1: [MPSAFE]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: irq maps: 0 0 0 0
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: irq maps: 0 0 0 0
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
ioapic0: routing intpin 4 (ISA IRQ 4) to vector 54
sio0: [FAST]
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0 0 0 0
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0 0 0 0
sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
ioapic0: routing intpin 3 (ISA IRQ 3) to vector 55
sio1: [FAST]
fdc0: <floppy drive controller (FDE)> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: ic_type 90 part_id 80
ioapic0: routing intpin 6 (ISA IRQ 6) to vector 56
fdc0: [MPSAFE]
fdc0: [FAST]
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
ioapic0: routing intpin 1 (ISA IRQ 1) to vector 57
atkbd0: [GIANT-LOCKED]
psm0: unable to allocate IRQ
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
fdc: fdc0 already exists; skipping it
sc: sc0 already exists; skipping it
sio: sio0 already exists; skipping it
sio: sio1 already exists; skipping it
vga: vga0 already exists; skipping it
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd1, terminal emulator: sc (syscons terminal)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
le0: not probed (disabled)
ppc0 failed to probe at irq 7 on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
ums0: <KYE Genius USB Wheel Mouse, class 0/0, rev 1.00/0.00, addr 2> on uhub0
ums0: 3 buttons and Z dir.
Device configuration finished.
procfs registered
lapic: Divisor 2, Frequency 49994562 hz
Timecounter "TSC" frequency 1999782196 Hz quality -100
Timecounters tick every 1.000 msec
splash: image decoder found: green_saver
lo0: bpf attached
ata0-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=80 wire
ad0: setting PIO4 on ICH3 chip
ad0: setting UDMA100 on ICH3 chip
ad0: 19092MB <WDC WD200BB-00CAA1 17.07W17> at ata0-master UDMA100
ad0: 39102336 sectors [38792C/16H/63S] 16 sectors/interrupt 1 depth queue
ad0: Intel check1 failed
ad0: Adaptec check1 failed
ad0: LSI (v3) check1 failed
ad0: LSI (v2) check1 failed
ad0: FreeBSD check1 failed
ATA PseudoRAID loaded
SMP: AP CPU #1 Launched!
cpu1 AP:
ID: 0x06000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
timer: 0x000200ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010000
ioapic0: Assigning ISA IRQ 1 to local APIC 0
ioapic0: Assigning ISA IRQ 3 to local APIC 6
ioapic0: Assigning ISA IRQ 4 to local APIC 0
ioapic0: Assigning ISA IRQ 6 to local APIC 6
ioapic0: Assigning ISA IRQ 9 to local APIC 0
ioapic0: Assigning ISA IRQ 14 to local APIC 6
ioapic0: Assigning ISA IRQ 15 to local APIC 0
ioapic0: Assigning PCI IRQ 16 to local APIC 6
ioapic0: Assigning PCI IRQ 18 to local APIC 0
ioapic4: Assigning PCI IRQ 96 to local APIC 6
GEOM: new disk ad0
Trying to mount root from ufs:/dev/ad0s1a
fdc0: output ready timeout
start_init: trying /sbin/init
fdc0: output ready timeout
fdc0: output ready timeout
fdc0: output ready timeout
fdc0: output ready timeout
fdc0: output ready timeout
fdc0: output ready timeout
fdc0: output ready timeout
fdc0: input ready timeout
fdc0: input ready timeout
fdc0: output ready timeout
fdc0: input ready timeout
fdc0: input ready timeout
fdc0: output ready timeout
fdc0: input ready timeout
fdc0: input ready timeout
fdc0: output ready timeout
fdc0: input ready timeout
fdc0: input ready timeout
More information about the freebsd-current
mailing list