misc/161715: Dell E6520 doesn't resume after ACPI suspend

[Sebastian Chmielewski]

>Number:         161715
>Category:       misc
>Synopsis:       Dell E6520 doesn't resume after ACPI suspend
>Confidential:   no
>Severity:       non-critical
>Priority:       low
>Responsible:    freebsd-bugs
>State:          open
>Quarter:        
>Keywords:       
>Date-Required:
>Class:          sw-bug
>Submitter-Id:   current-users
>Arrival-Date:   Sun Oct 16 16:00:23 UTC 2011
>Closed-Date:
>Last-Modified:
>Originator:     Sebastian Chmielewski
>Release:        
>Organization:
>Environment:
>Description:
Dell E6520 can't resume after suspend - power is on but nothing can be seen on LCD. I did a procedure described in Handbook:
- sysctl debug.bootverbose=1
- sysctl debug.acpi.suspend_bounce=1
- acpiconf -s 3
Output from console:
ehci0: wake_prep disabled wake for \_SB_.PCI0.EHC2 (S3)
ehci1: wake_prep disabled wake for \_SB_.PCI0.EHCI (S3)
acpi_lid0: wake_prep enabled for \_SB_.LID_ (S3)
acpi_button0: wake_prep enabled for \_SB_.PBTN (S3)
pci0:0:25:0: Transition from D3 to D0
pci0:0:27:0: Transition from D3 to D0
pci0:0:31:2: Transition from D3 to D0
pci0:1:0:0: Transition from D3 to D0
pci0:1:0:1: Transition from D3 to D0
vgapci0: calling BIOS POST
hdac1: Enabling headphone/speaker audio routing switching:
hdac1:  as=0 sense nid=11 [UNSOL]
hdac1: Pin sense: nid=11 res=0x00000000
pci0:3:0:0: Transition from D3 to D0
pci0:11:0:0: Transition from D3 to D0
pci0:11:0:1: Transition from D3 to D0
fwohci0: Phy 1394a available S400, 1 ports.
fwohci0: Link S400, max_rec 2048 bytes.
fwohci0: Initiate bus reset
fwohci0: fwohci_intr_core: BUS reset
fwohci0: fwohci_intr_core: node_id=0x00000000, SelfID Count=1, non CYCLEMASTER mode
firewire0: 2 nodes, maxhop <= 1 cable IRM irm(1) 
mmc0: Probing bus
mmc0: SD 2.0 interface conditions: OK
mmc0: SD probe: OK (OCR: 0x00ff8000)
mmc0: Current OCR: 0x00ff8000
firewire0: fw_rcv: unknown response RRESQ(6) src=0xffc1 tl=0x1 rt=1 data=0xdd284f04
mmc0: Probing cards
mmc0: Card detected (CID 275048534430384730b00005b400a500)
mmc0: Card at relative address 7:
mmc0:  card: SD High Capacity (0x27/0x5048/"SD08G" rev 3.0 m/d 05.2010 s/n b00005b4)
mmc0:  bus: 4bit, 50MHz, high speed timing
mmc0:  memory: 15704064 blocks, erase sector 8192 blocks
mmc0: setting transfer rate to 50.000MHz (high speed timing)
ahcich0: AHCI reset...
ahcich0: SATA connect time=1000us status=00000123
ahcich0: AHCI reset: device found
ahcich1: AHCI reset...
ahcich1: SATA connect time=1800us status=00000113
ahcich1: AHCI reset: device found
ahcich1: AHCI reset: device ready after 0ms
ahcich2: AHCI reset...
ahcich2: SATA connect timeout time=10000us status=00000000
ahcich2: AHCI reset: device not found
ahcich3: AHCI reset...
ahcich3: SATA connect timeout time=10000us status=00000000
ahcich3: AHCI reset: device not found
ahcich4: AHCI reset...
ahcich4: SATA connect timeout time=10000us status=00000000
ahcich4: AHCI reset: device not found
battery1: battery0: battery2: battery initialization start
battery initialization start
battery initialization start
battery0: battery initialization done, tried 1 times
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
firewire0: ahcich0: split transaction timeout: tl=0x15 flag=0x04
AHCI reset: device ready after 100ms
send: dst=0x01 tl=0x15 rt=0 tcode=0x4 pri=0x0 src=0x000
firewire0: fw_explore_node: node1: explore_read_quads failure
firewire0: fw_rcv: unknown response RRESQ(6) src=0xffc1 tl=0x2 rt=1 data=0x34393331
uhub2: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on usbus0
firewire0: split transaction timeout: tl=0x16 flag=0x04
send: dst=0x01 tl=0x16 rt=0 tcode=0x4 pri=0x0 src=0x000
firewire0: fw_explore_node: node1: explore_read_quads failure
firewire0: fw_rcv: unknown response RRESQ(6) src=0xffc1 tl=0x3 rt=1 data=0x12a064f0
firewire0: split transaction timeout: tl=0x17 flag=0x04
send: dst=0x01 tl=0x17 rt=0 tcode=0x4 pri=0x0 src=0x000
firewire0: fw_explore_node: node1: explore_read_quads failure
uhub2: 6 ports with 6 removable, self powered
ugen0.3: <Dell Computer Corp> at usbus0
ubt0: <Dell Computer Corp DW375 Bluetooth Module, class 224/1, rev 2.00/5.17, addr 3> on usbus0
ugen0.4: <CN0CJ3P27248717L025LA01> at usbus0
battery2: battery initialization failed, giving up
battery1: battery initialization failed, giving up
>How-To-Repeat:

>Fix:


>Release-Note:
>Audit-Trail:
>Unformatted: