kern/110407: [ata] ATA drivers not recognizing Seagate CF
Microdrive [regression]
Nenhum_de_Nos
matheus at eternamente.info
Thu Jun 4 02:40:02 UTC 2009
The following reply was made to PR kern/110407; it has been noted by GNATS.
From: Nenhum_de_Nos <matheus at eternamente.info>
To: bug-followup at FreeBSD.org, modemwh0re at gmail.com
Cc:
Subject: Re:kern/110407: [ata] ATA drivers not recognizing Seagate CF
Microdrive [regression]
Date: Wed, 3 Jun 2009 23:07:58 -0300
just to add info:
verbose dmesg it should be ad0:
Copyright (c) 1992-2009 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.0-HEAD-20090501-JPSNAP #0: Fri May 1 04:22:31 UTC 2009
root at build-i386-fbsd-2.allbsd.org:/usr/obj/i386/usr/src/sys/GENERIC
WARNING: WITNESS option enabled, expect reduced performance.
Preloaded elf kernel "/boot/kernel/kernel" at 0xc10b7000.
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 798130616 Hz
CPU: Transmeta(tm) Crusoe(tm) Processor TM5700 (798.13-MHz 586-class CPU)
Origin = "GenuineTMx86" Id = 0x543 Stepping = 3
Features=0x84893f<FPU,VME,DE,PSE,TSC,MSR,CX8,SEP,CMOV,PN,MMX>
Processor revision 1.5.0.2
Code Morphing Software revision 4.5.2-12-11
20040614 15:00 official release 4.5.2#1
real memory = 136314880 (130 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x0000000000099fff, 626688 bytes (153 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000001425000 - 0x0000000006dd1fff, 94031872 bytes (22957 pages)
avail memory = 95813632 (91 MB)
bios32: Found BIOS32 Service Directory header at 0xc00f9de0
bios32: Entry = 0xfa260 (c00fa260) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0xa290
pnpbios: Found PnP BIOS data at 0xc00facf0
pnpbios: Entry = f0000:ad20 Rev = 1.0
Other BIOS signatures found:
ULE: setup cpu 0
wlan: <802.11 Link Layer>
null: <null device, zero device>
random: <entropy source, Software, Yarrow>
nfslock: pseudo-device
kbd: new array size 4
kbd1 at kbdmux0
io: <I/O>
mem: <memory>
hptrr: RocketRAID 17xx/2xxx SATA controller driver v1.2 (May 1 2009 04:21:18)
npx0: INT 16 interface
pci_open(1): mode 1 addr port (0x0cf8) is 0x80000058
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=80] is there (id=03951279)
pcibios: BIOS version 2.10
pcib0: <Host to PCI bridge> pcibus 0 on motherboard
pir0: <PCI Interrupt Routing Table: 5 Entries> on motherboard
$PIR: Links after initial probe:
Link IRQ Rtd Ref IRQs
0x2 255 N 3 3 4 5 7 9 10 11 14 15
0x3 255 N 4 3 4 5 7 9 10 11 14 15
0x5 255 N 4 3 4 5 7 9 10 11 14 15
0x1 255 N 4 3 4 5 7 9 10 11 14 15
$PIR: Found matching pin for 0.11.INTA at func 0: 15
$PIR: Found matching pin for 0.13.INTA at func 0: 10
$PIR: Found matching pin for 0.9.INTA at func 0: 11
$PIR: Found matching pin for 0.9.INTB at func 1: 15
$PIR: Found matching pin for 0.9.INTC at func 2: 5
$PIR: Found matching pin for 0.18.INTA at func 0: 11
$PIR: Links after initial IRQ discovery:
Link IRQ Rtd Ref IRQs
0x2 15 Y 3 3 4 5 7 9 10 11 14 15
0x3 5 Y 4 3 4 5 7 9 10 11 14 15
0x5 10 Y 4 3 4 5 7 9 10 11 14 15
0x1 11 Y 4 3 4 5 7 9 10 11 14 15
$PIR: IRQs used by BIOS: 5 10 11 15
$PIR: Interrupt Weights:
[ 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 ]
[ 0 0 0 0 0 4 0 0 0 0 4 4 0 0 0 3 ]
pci0: <PCI bus> on pcib0
pci0: domain=0, physical bus=0
found-> vendor=0x1279, dev=0x0395, revid=0x04
domain=0, bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0006, statreg=0x2200, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type Memory, range 32, base 0xe8000000, size 20, enabled
found-> vendor=0x1279, dev=0x0396, revid=0x00
domain=0, bus=0, slot=0, func=1
class=05-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1279, dev=0x0397, revid=0x00
domain=0, bus=0, slot=0, func=2
class=05-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1279, dev=0x0399, revid=0x00
domain=0, bus=0, slot=0, func=3
class=05-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1106, dev=0x3038, revid=0x61
domain=0, bus=0, slot=9, func=0
class=0c-03-00, hdrtype=0x00, mfdev=1
cmdreg=0x0147, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
map[20]: type I/O Port, range 32, base 0xe000, size 5, enabled
$PIR: 0:9 INTA routed to irq 11
found-> vendor=0x1106, dev=0x3038, revid=0x61
domain=0, bus=0, slot=9, func=1
class=0c-03-00, hdrtype=0x00, mfdev=1
cmdreg=0x0147, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=15
powerspec 2 supports D0 D1 D2 D3 current D0
map[20]: type I/O Port, range 32, base 0xe100, size 5, enabled
$PIR: 0:9 INTB routed to irq 15
found-> vendor=0x1106, dev=0x3104, revid=0x63
domain=0, bus=0, slot=9, func=2
class=0c-03-20, hdrtype=0x00, mfdev=1
cmdreg=0x0147, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=c, irq=5
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type Memory, range 32, base 0xe8192000, size 8, enabled
$PIR: 0:9 INTC routed to irq 5
found-> vendor=0x1095, dev=0x3114, revid=0x02
domain=0, bus=0, slot=11, func=0
class=01-04-00, hdrtype=0x00, mfdev=0
cmdreg=0x0147, statreg=0x02b0, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=15
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type I/O Port, range 32, base 0xe200, size 3, enabled
map[14]: type I/O Port, range 32, base 0xe300, size 2, enabled
map[18]: type I/O Port, range 32, base 0xe400, size 3, enabled
map[1c]: type I/O Port, range 32, base 0xe500, size 2, enabled
map[20]: type I/O Port, range 32, base 0xe600, size 4, enabled
map[24]: type Memory, range 32, base 0xe8190000, size 10, enabled
$PIR: 0:11 INTA routed to irq 15
found-> vendor=0x1002, dev=0x5159, revid=0x00
domain=0, bus=0, slot=13, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0187, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
intpin=a, irq=10
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type Prefetchable Memory, range 32, base 0xe0000000, size 27, enabled
map[14]: type I/O Port, range 32, base 0xe700, size 8, enabled
map[18]: type Memory, range 32, base 0xe8180000, size 16, enabled
$PIR: 0:13 INTA routed to irq 10
found-> vendor=0x1106, dev=0x8231, revid=0x10
domain=0, bus=0, slot=17, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0087, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
found-> vendor=0x1106, dev=0x0571, revid=0x06
domain=0, bus=0, slot=17, func=1
class=01-01-8a, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
map[20]: type I/O Port, range 32, base 0xe800, size 4, enabled
found-> vendor=0x1106, dev=0x8235, revid=0x10
domain=0, bus=0, slot=17, func=4
class=06-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0000, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
found-> vendor=0x1106, dev=0x3065, revid=0x51
domain=0, bus=0, slot=18, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0147, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x03 (750 ns), maxlat=0x08 (2000 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type I/O Port, range 32, base 0xeb00, size 8, enabled
map[14]: type Memory, range 32, base 0xe8191000, size 8, enabled
$PIR: 0:18 INTA routed to irq 11
pci0: <memory, RAM> at device 0.1 (no driver attached)
pci0: <memory, RAM> at device 0.2 (no driver attached)
pci0: <memory, RAM> at device 0.3 (no driver attached)
uhci0: <VIA 83C572 USB controller> port 0xe000-0xe01f irq 11 at device 9.0 on pci0
uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0xe000
uhci0: [MPSAFE]
uhci0: [ITHREAD]
uhci0: LegSup = 0x201a
usbus0: <VIA 83C572 USB controller> on uhci0
uhci1: <VIA 83C572 USB controller> port 0xe100-0xe11f irq 15 at device 9.1 on pci0
uhci1: Reserved 0x20 bytes for rid 0x20 type 4 at 0xe100
uhci1: [MPSAFE]
uhci1: [ITHREAD]
uhci1: LegSup = 0x2010
usbus1: <VIA 83C572 USB controller> on uhci1
ehci0: <VIA VT6202 USB 2.0 controller> mem 0xe8192000-0xe81920ff irq 5 at device 9.2 on pci0
ehci0: Reserved 0x100 bytes for rid 0x10 type 3 at 0xe8192000
ehci0: [MPSAFE]
ehci0: [ITHREAD]
usbus2: EHCI version 1.0
usbus2: <VIA VT6202 USB 2.0 controller> on ehci0
atapci0: <SiI 3114 SATA150 controller> port 0xe200-0xe207,0xe300-0xe303,0xe400-0xe407,0xe500-0xe503,0xe600-0xe60f mem 0xe8190000-0xe81903ff irq 15 at device 11.0 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xe600
atapci0: [MPSAFE]
atapci0: [ITHREAD]
atapci0: Reserved 0x400 bytes for rid 0x24 type 3 at 0xe8190000
ata2: <ATA channel 0> on atapci0
ata2: SATA connect time=0ms status=00000113
ata2: reset tp1 mask=01 ostat0=50 ostat1=00
ata2: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata2: reset tp2 stat0=50 stat1=00 devices=0x1
ata2: [MPSAFE]
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci0
ata3: SATA connect timeout status=00000000
ata3: [MPSAFE]
ata3: [ITHREAD]
ata4: <ATA channel 2> on atapci0
ata4: SATA connect timeout status=00000000
ata4: [MPSAFE]
ata4: [ITHREAD]
ata5: <ATA channel 3> on atapci0
ata5: SATA connect timeout status=00000000
ata5: [MPSAFE]
ata5: [ITHREAD]
vgapci0: <VGA-compatible display> port 0xe700-0xe7ff mem 0xe0000000-0xe7ffffff,0xe8180000-0xe818ffff irq 10 at device 13.0 on pci0
isab0: <PCI-ISA bridge> at device 17.0 on pci0
isa0: <ISA bus> on isab0
atapci1: <VIA 8231 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xe800-0xe80f at device 17.1 on pci0
atapci1: Reserved 0x10 bytes for rid 0x20 type 4 at 0xe800
ata0: <ATA channel 0> on atapci1
atapci1: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci1: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=58 ostat1=00
ata0: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=50 stat1=00 devices=0x1
ata0: [MPSAFE]
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci1
atapci1: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci1: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=00 ostat0=ff ostat1=ff
ata1: [MPSAFE]
ata1: [ITHREAD]
pci0: <bridge> at device 17.4 (no driver attached)
vr0: <VIA VT6102 Rhine II 10/100BaseTX> port 0xeb00-0xebff mem 0xe8191000-0xe81910ff irq 11 at device 18.0 on pci0
vr0: Quirks: 0x0
vr0: Revision: 0x51
vr0: Reserved 0x100 bytes for rid 0x10 type 4 at 0xeb00
miibus0: <MII bus> on vr0
ukphy0: <Generic IEEE 802.3u media interface> PHY 1 on miibus0
ukphy0: OUI 0x004063, model 0x0032, rev. 10
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
vr0: bpf attached
vr0: Ethernet address: 00:13:21:ee:26:00
vr0: [MPSAFE]
vr0: [ITHREAD]
cpu0 on motherboard
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
ahc_isa_probe 14: ioport 0xec00 alloc failed
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
ex_isa_identify()
pnpbios: 11 devices, largest 78 bytes
PNP0200: adding dma mask 0x10
PNP0200: adding io range 0-0xf, size=0x10, align=0
PNP0200: adding io range 0x81-0x83, size=0x3, align=0
PNP0200: adding io range 0x87-0x87, size=0x1, align=0
PNP0200: adding io range 0x89-0x8b, size=0x3, align=0
PNP0200: adding io range 0x8f-0x91, size=0x3, align=0
PNP0200: adding io range 0xc0-0xdf, size=0x20, align=0
pnpbios: handle 1 device ID PNP0200 (0002d041)
PNP0100: adding irq mask 0x1
PNP0100: adding io range 0x40-0x43, size=0x4, align=0
pnpbios: handle 2 device ID PNP0100 (0001d041)
PNP0b00: adding irq mask 0x100
PNP0b00: adding io range 0x70-0x71, size=0x2, align=0
pnpbios: handle 3 device ID PNP0b00 (000bd041)
PNP0303: adding irq mask 0x2
PNP0303: adding io range 0x60-0x60, size=0x1, align=0
PNP0303: adding io range 0x64-0x64, size=0x1, align=0
pnpbios: handle 4 device ID PNP0303 (0303d041)
PNP0800: adding io range 0x61-0x61, size=0x1, align=0
pnpbios: handle 5 device ID PNP0800 (0008d041)
PNP0c04: adding irq mask 0x2000
PNP0c04: adding io range 0xf0-0xff, size=0x10, align=0
pnpbios: handle 6 device ID PNP0c04 (040cd041)
PNP0c01: adding fixed memory32 range 0-0x9ffff, size=0xa0000
PNP0c01: adding fixed memory32 range 0xfffe0000-0xffffffff, size=0x20000
PNP0c01: adding fixed memory32 range 0xfff80000-0xfffdffff, size=0x60000
PNP0c01: adding fixed memory32 range 0xfee00000-0xfee0ffff, size=0x10000
PNP0c01: adding fixed memory32 range 0x100000-0xffffff, size=0xf00000
pnpbios: handle 7 device ID PNP0c01 (010cd041)
PNP0c02: adding fixed memory32 range 0xf0000-0xf3fff, size=0x4000
PNP0c02: adding fixed memory32 range 0xf4000-0xf7fff, size=0x4000
PNP0c02: adding fixed memory32 range 0xf8000-0xfffff, size=0x8000
PNP0c02: adding fixed memory32 range 0xda000-0xdbfff, size=0x2000
pnpbios: handle 8 device ID PNP0c02 (020cd041)
PNP0a03: adding io range 0x4d0-0x4d1, size=0x2, align=0
PNP0a03: adding io range 0xcf8-0xcff, size=0x8, align=0
PNP0a03: adding io range 0x4000-0x407f, size=0x80, align=0
PNP0a03: adding io range 0x4080-0x40ff, size=0x80, align=0
PNP0a03: adding io range 0x5000-0x501f, size=0x20, align=0
PNP0a03: adding io range 0x6000-0x607f, size=0x80, align=0
pnpbios: handle 9 device ID PNP0a03 (030ad041)
PNP0700: adding dma mask 0x4
PNP0700: adding io range 0x3f2-0x3f5, size=0x4, align=0
PNP0700: adding io range 0x3f7-0x3f7, size=0x1, align=0
PNP0700: adding irq mask 0x40
pnpbios: handle 13 device ID PNP0700 (0007d041)
isa_probe_children: disabling PnP devices
pmtimer0 on isa0
atrtc0: <AT realtime clock> at port 0x70-0x71 irq 8 pnpid PNP0b00 on isa0
atrtc0: registered as a time-of-day clock (resolution 1000000us)
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 irq 1 pnpid PNP0303 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0067
atkbd: keyboard ID 0xffffffff (1)
atkbd: failed to reset the keyboard.
kbd0 at atkbd0
kbd0: atkbd0, AT 84 (1), config:0x0, flags:0x3d0000
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: unable to allocate IRQ
unknown: <AT Real Time Clock> failed to probe at port 0x61 pnpid PNP0800 on isa0
unknown: <PNP0c01> can't assign resources (memory)
unknown: <PNP0c01> at iomem 0-0x9ffff pnpid PNP0c01 on isa0
unknown: <AT Real Time Clock> failed to probe at port 0x3f2-0x3f5,0x3f7 irq 6 drq 2 pnpid PNP0700 on isa0
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
atrtc: atrtc0 already exists; skipping it
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: probing non-PnP devices
orm0: <ISA Option ROMs> at iomem 0xc0000-0xc8fff,0xcc000-0xcffff,0xd0000-0xd9fff pnpid ORM0000 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd1, terminal emulator: scteken (teken terminal)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fdc0 failed to probe at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fe0: not probed (disabled)
ie0: not probed (disabled)
le0: not probed (disabled)
ppc0: parallel port not found.
ppc0: <Parallel port> failed to probe at irq 7 on isa0
sn0: not probed (disabled)
uart0: <ns8250> failed to probe at port 0x3f8-0x3ff irq 4 on isa0
uart1: <ns8250> failed to probe at port 0x2f8-0x2ff irq 3 on isa0
uart2: not probed (disabled)
uart3: not probed (disabled)
isa_probe_children: probing PnP devices
unknown: <PNP0c01> can't assign resources (memory)
unknown: <PNP0c01> at iomem 0-0x9ffff pnpid PNP0c01 on isa0
Device configuration finished.
procfs registered
Timecounter "TSC" frequency 798130616 Hz quality 800
Timecounters tick every 1.000 msec
lo0: bpf attached
hptrr: no controller detected.
ata0: Identifying devices: 00000001
ata0: New devices: 00000001
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 480Mbps High Speed USB v2.0
ugen0.1: <VIA> at usbus0
uhub0: <VIA UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <VIA> at usbus1
uhub1: <VIA UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <VIA> at usbus2
uhub2: <VIA EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
ata0: reiniting channel ..
ata0: reset tp1 mask=03 ostat0=58 ostat1=00
ata0: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=50 stat1=00 devices=0x1
ata0: reinit done ..
unknown: FAILURE - ATA_IDENTIFY timed out LBA=0
uhub2: 4 ports with 4 removable, self powered
ata0: reiniting channel ..
ata0: reset tp1 mask=03 ostat0=58 ostat1=00
ata0: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: stat1=0x00 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 stat0=50 stat1=00 devices=0x1
ata0: reinit done ..
unknown: FAILURE - ATA_IDENTIFY timed out LBA=0
ata1: Identifying devices: 00000000
ata1: New devices: 00000000
ata2: Identifying devices: 00000001
ata2: New devices: 00000001
ata2-master: pio=PIO4 wdma=WDMA2 udma=UDMA33 cable=40 wire
ad4: 6149MB <SAMSUNG SV0643D KT100> at ata2-master SATA150
ad4: 12594960 sectors [13328C/15H/63S] 16 sectors/interrupt 1 depth queue
GEOM: new disk ad4
ad4: Silicon Image check1 failed
ad4: Adaptec check1 failed
ad4: LSI (v3) check1 failed
ad4: LSI (v2) check1 failed
ad4: FreeBSD check1 failed
ata3: Identifying devices: 00000000
ata3: New devices: 00000000
ata4: Identifying devices: 00000000
ata4: New devices: 00000000
ata5: Identifying devices: 00000000
ata5: New devices: 00000000
ATA PseudoRAID loaded
WARNING: WITNESS option enabled, expect reduced performance.
GEOM: ad4s1: geometry does not match label (255h,63s != 15h,63s).
GEOM: ad4s2: geometry does not match label (255h,63s != 15h,63s).
GEOM_LABEL: Label for provider ad4s1a is ufsid/48a498393b6d8bea.
Trying to mount root from ufs:/dev/ad4s1a
ct_to_ts([2009-05-04 22:10:17]) = 1241475017.000000000
start_init: trying /sbin/init
ugen1.2: <GM-TEK> at usbus1
ukbd0: <HID Keyboard> on usbus1
kbd2 at ukbd0
kbd2: ukbd0, generic (0), config:0x0, flags:0x3d0000
ums0: <HID Mouse> on usbus1
ums0: 3 buttons and [XYZ] coordinates ID=0
GEOM_LABEL: Label ufsid/48a498393b6d8bea removed.
GEOM_LABEL: Label for provider ad4s1a is ufsid/48a498393b6d8bea.
GEOM_LABEL: Label ufsid/48a498393b6d8bea removed.
splash: image decoder found: green_saver
pciconf -lv:
hostb0 at pci0:0:0:0: class=0x060000 card=0x02951279 chip=0x03951279 rev=0x04 hdr=0x00
vendor = 'Transmeta Corp.'
device = 'LongRun Northbridge'
class = bridge
subclass = HOST-PCI
none0 at pci0:0:0:1: class=0x050000 card=0x02951279 chip=0x03961279 rev=0x00 hdr=0x00
vendor = 'Transmeta Corp.'
device = 'SDRAM Controller'
class = memory
subclass = RAM
none1 at pci0:0:0:2: class=0x050000 card=0x02951279 chip=0x03971279 rev=0x00 hdr=0x00
vendor = 'Transmeta Corp.'
device = 'BIOS scratchpad'
class = memory
subclass = RAM
none2 at pci0:0:0:3: class=0x050000 card=0x00000000 chip=0x03991279 rev=0x00 hdr=0x00
vendor = 'Transmeta Corp.'
class = memory
subclass = RAM
uhci0 at pci0:0:9:0: class=0x0c0300 card=0x30381106 chip=0x30381106 rev=0x61 hdr=0x00
vendor = 'VIA Technologies Inc'
device = 'VT83C572, VT6202 VIA Rev 5 or later USB Universal Host Controller'
class = serial bus
subclass = USB
uhci1 at pci0:0:9:1: class=0x0c0300 card=0x30381106 chip=0x30381106 rev=0x61 hdr=0x00
vendor = 'VIA Technologies Inc'
device = 'VT83C572, VT6202 VIA Rev 5 or later USB Universal Host Controller'
class = serial bus
subclass = USB
ehci0 at pci0:0:9:2: class=0x0c0320 card=0x31041106 chip=0x31041106 rev=0x63 hdr=0x00
vendor = 'VIA Technologies Inc'
device = 'VT6202/12 USB 2.0 Enhanced Host Controller'
class = serial bus
subclass = USB
atapci0 at pci0:0:11:0: class=0x010400 card=0x61141095 chip=0x31141095 rev=0x02 hdr=0x00
vendor = 'Silicon Image Inc (Was: CMD Technology Inc)'
device = 'Sil 3114 SATALink/SATARaid Controller'
class = mass storage
subclass = RAID
vgapci0 at pci0:0:13:0: class=0x030000 card=0x51591002 chip=0x51591002 rev=0x00 hdr=0x00
vendor = 'ATI Technologies Inc'
device = 'RV100 Radeon 7000 / Radeon VE'
class = display
subclass = VGA
isab0 at pci0:0:17:0: class=0x060100 card=0x00001106 chip=0x82311106 rev=0x10 hdr=0x00
vendor = 'VIA Technologies Inc'
device = 'VT8231 PCI to ISA Bridge'
class = bridge
subclass = PCI-ISA
atapci1 at pci0:0:17:1: class=0x01018a card=0x05711106 chip=0x05711106 rev=0x06 hdr=0x00
vendor = 'VIA Technologies Inc'
device = 'VT82C586A/B/VT82C686/A/B/VT823x/A/C Bus Master IDE Controller'
class = mass storage
subclass = ATA
none3 at pci0:0:17:4: class=0x068000 card=0x82351106 chip=0x82351106 rev=0x10 hdr=0x00
vendor = 'VIA Technologies Inc'
device = 'VT8751 Power Management Controller'
class = bridge
vr0 at pci0:0:18:0: class=0x020000 card=0x01021106 chip=0x30651106 rev=0x51 hdr=0x00
vendor = 'VIA Technologies Inc'
device = 'VT6102 Rhine II PCI Fast Ethernet Controller||Used by GERICOM in laptop Webengine Advanced'
class = network
subclass = ethernet
I can confirm it not working in 8-current as of this day (see dmesg above)
matheus
--
We will call you cygnus,
The God of balance you shall be
A: Because it messes up the order in which people normally read text.
Q: Why is top-posting such a bad thing?
http://en.wikipedia.org/wiki/Posting_style
More information about the freebsd-bugs
mailing list