Orange pi one ,receive panic: bad pte2

Tue Jan 16 13:19:26 UTC 2018

OKOK below is booting message.

U-Boot SPL 2017.07 (Oct 20 2017 - 12:55:15)
DRAM: 512 MiB
Trying to boot from MMC1

U-Boot 2017.07 (Oct 20 2017 - 12:55:15 +0000) Allwinner Technology

CPU:   Allwinner H3 (SUN8I 1680)
Model: Xunlong Orange Pi One
DRAM:  512 MiB
MMC:   SUNXI SD/MMC: 0
In:    serial
Out:   serial
Err:   serial
Net:   phy interface0
eth0: ethernet at 1c30000
starting USB...
USB0:   USB EHCI 1.00
USB1:   USB OHCI 1.0
scanning bus 0 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot:  0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found FreeBSD U-Boot Loader (bin)
reading ubldr.bin
232932 bytes read in 33 ms (6.7 MiB/s)
## Starting application at 0x42000000 ...
Consoles: U-Boot console
Compatible U-Boot API signature found @0x59f4c490

FreeBSD/armv6 U-Boot loader, Revision 1.2
(Mon Jan 15 04:39:27 CST 2018 root at VirtualBox pi)

DRAM: 512MB
MMC Device 1 not found
MMC Device 2 not found
MMC Device 3 not found
Number of U-Boot devices: 1
U-Boot env: loaderdev not set, will probe all devices.
Found U-Boot device: disk
  Probing all disk devices...
  Checking unit=0 slice=<auto> partition=<auto>... good.
Booting from disk0s2a:
/boot/kernel/kernel data=0x862c1c+0x1dd3e4 syms=[0x4+0x979b0+0x4+0xdca9d]

Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]...
/boot/dtb/u-boot.dtb size=0x2f09
Loaded DTB from file 'u-boot.dtb'.
Kernel entry at 0x42200100...
Kernel args: (null)
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1992-2018 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 12.0-CURRENT #0 r327807: Sun Jan 14 03:22:38 CST 2018
    root at VirtualBox
pi:/opt/head_327807_obj/obj/opt/head_327807/arm.armv6/sys/GENERIC arm
FreeBSD clang version 5.0.1 (tags/RELEASE_501/final 320880) (based on LLVM
5.0.1)
WARNING: WITNESS option enabled, expect reduced performance.
VT: init without driver.
module_register: cannot register simplebus/ahci from kernel; already loaded
from kernel
Module simplebus/ahci failed to register: 17
module_register: cannot register simplebus/ehci from kernel; already loaded
from kernel
Module simplebus/ehci failed to register: 17
module_register: cannot register simplebus/pcib from kernel; already loaded
from kernel
Module simplebus/pcib failed to register: 17
module_register: cannot register simplebus/ehci from kernel; already loaded
from kernel
Module simplebus/ehci failed to register: 17
CPU: ARM Cortex-A7 r0p5 (ECO: 0x00000000)
CPU Features:
  Multiprocessing, Thumb2, Security, Virtualization, Generic Timer, VMSAv7,
  PXN, LPAE, Coherent Walk
Optional instructions:
  SDIV/UDIV, UMULL, SMULL, SIMD(ext)
LoUU:2 LoC:3 LoUIS:2
Cache level 1:
 32KB/64B 4-way data cache WB Read-Alloc Write-Alloc
 32KB/32B 2-way instruction cache Read-Alloc
Cache level 2:
 512KB/64B 8-way unified cache WB Read-Alloc Write-Alloc
real memory  = 536870912 (512 MB)
avail memory = 508055552 (484 MB)
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
arc4random: no preloaded entropy cache
random: entropy device external interface
kbd0 at kbdmux0
ofwbus0: <Open Firmware Device Tree>
aw_ccu0: <Allwinner Clock Control Unit> on ofwbus0
clk_fixed0: <Fixed clock> on aw_ccu0
clk_fixed1: <Fixed clock> on aw_ccu0
clk_fixed2: <Fixed factor clock> on aw_ccu0
aw_gate0: <Allwinner APB0 Clock Gates> mem 0x1f01428-0x1f0142b on aw_ccu0
aw_modclk0: <Allwinner Module Clock> mem 0x1f01454-0x1f01457 on aw_ccu0
simplebus0: <Flattened device tree simple bus> on ofwbus0
aw_ccung0: <Allwinner Clock Control Unit NG> mem 0x1c20000-0x1c203ff on
simplebus0
aw_reset0: <Allwinner Module Resets> mem 0x1f014b0-0x1f014b3 on simplebus0
regfix0: <Fixed Regulator> on ofwbus0
regfix1: <Fixed Regulator> on ofwbus0
regfix2: <Fixed Regulator> on ofwbus0
awusbphy0: <Allwinner USB PHY> mem
0x1c19400-0x1c1942b,0x1c1a800-0x1c1a803,0x1c1b800-0x1c1b803,0x1c1c800-0x1c1c803,0x1c1d800-0x1c1d803
on simplebus0
gic0: <ARM Generic Interrupt Controller> mem
0x1c81000-0x1c81fff,0x1c82000-0x1c82fff,0x1c84000-0x1c85fff,0x1c86000-0x1c87fff
irq 24 on simplebus0
gic0: pn 0x1, arch 0x2, rev 0x1, implementer 0x43b irqs 160
gpio0: <Allwinner GPIO/Pinmux controller> mem 0x1c20800-0x1c20bff irq 14,15
on simplebus0
gpiobus0: <OFW GPIO bus> on gpio0
gpio1: <Allwinner GPIO/Pinmux controller> mem 0x1f02c00-0x1f02fff irq 28 on
simplebus0
gpiobus1: <OFW GPIO bus> on gpio1
generic_timer0: <ARMv7 Generic Timer> irq 0,1,2,3 on ofwbus0
Timecounter "ARM MPCore Timecounter" frequency 24000000 Hz quality 1000
Event timer "ARM MPCore Eventtimer" frequency 24000000 Hz quality 1000
rtc0: <Allwinner RTC> mem 0x1f00000-0x1f00053 irq 25,26 on simplebus0
rtc0: registered as a time-of-day clock, resolution 1.000000s
syscon_generic0: <syscon> mem 0x1c00000-0x1c00033 on simplebus0
cpulist0: <Open Firmware CPU Group> on ofwbus0
cpu0: <Open Firmware CPU> on cpulist0
cpu1: <Open Firmware CPU> on cpulist0
cpu2: <Open Firmware CPU> on cpulist0
cpu3: <Open Firmware CPU> on cpulist0
a31dmac0: <Allwinner DMA controller> mem 0x1c02000-0x1c02fff irq 4 on
simplebus0
aw_mmc0: <Allwinner Integrated MMC/SD controller> mem 0x1c0f000-0x1c0ffff
irq 5 on simplebus0
mmc0: <MMC/SD bus> on aw_mmc0
ehci0: <Allwinner Integrated USB 2.0 controller> mem 0x1c1b000-0x1c1b0ff
irq 8 on simplebus0
usbus0: EHCI version 1.0
usbus0 on ehci0
ohci0: <Generic OHCI Controller> mem 0x1c1b400-0x1c1b4ff irq 9 on simplebus0
usbus1 on ohci0
gpioc0: <GPIO controller> on gpio0
aw_wdog0: <Allwinner A31 Watchdog> mem 0x1c20ca0-0x1c20cbf irq 18 on
simplebus0
uart0: <16750 or compatible> mem 0x1c28000-0x1c283ff irq 19 on simplebus0
uart0: console (115384,n,8,1)
uart1: <Non-standard ns8250 class UART with FIFOs> mem 0x1c28400-0x1c287ff
irq 20 on simplebus0
awg0: <Allwinner Gigabit Ethernet> mem
0x1c30000-0x1c30103,0x1c00030-0x1c00033 irq 23 on simplebus0
awg0: cannot get tx clock
miibus0: <MII bus> on awg0
ukphy0: <Generic IEEE 802.3u media interface> PHY 0 on miibus0
ukphy0:  none, 10baseT-FDX, 100baseTX
ukphy1: <Generic IEEE 802.3u media interface> PHY 1 on miibus0
ukphy1:  none, 10baseT-FDX, 100baseTX
awg0: Ethernet address: 02:81:ae:83:0f:fa
gpioc1: <GPIO controller> on gpio1
gpioled0: <GPIO LEDs> on ofwbus0
cryptosoft0: <software crypto>
Timecounters tick every 1.000 msec
usbus0: 480Mbps High Speed USB v2.0
usbus1: 12Mbps Full Speed USB v1.0
ugen0.1: <Allwinner EHCI root HUB> at usbus0
uhub0: <Allwinner EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
ugen1.1: <Generic OHCI root HUB> at usbus1
uhub1: <Generic OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
mmcsd0: 16GB <SDHC USDU1 2.0 SN 42F16FB1 MFG 12/2017 by 116 J`> at mmc0
50.0MHz/4bit/65535-block
Release APs
WARNING: WITNESS option enabled, expect reduced performance.
arc4random: no preloaded entropy cache
Trying to mount root from ufs:/dev/mmcsd0s2a [rw]...
uhub1: 1 port with 1 removable, self powered
arc4random: no preloaded entropy cache
uhub0: 1 port with 1 removable, self powered
arc4random: no preloaded entropy cache
/etc/rc: WARNING: hostid: unable to figure out a UUID from DMI data,
generating a new one
Setting hostuuid: 6c68013f-fac6-11e7-a689-d969c7db3a6e.
Setting hostid: 0xa8b75395.
No suitable dump device was found.
Starting file system checks:
Mounting local filesystems:.
ELF ldconfig path: /lib /usr/lib /usr/lib/compat
random: unblocking device.
Soft Float compatibility ldconfig path:
Setting hostname: head_pi.
Setting up harvesting:
[UMA],[FS_ATIME],SWI,INTERRUPT,NET_NG,NET_ETHER,NET_TUN,MOUSE,KEYBOARD,ATTACH,CACHED
Feeding entropy: .
Starting Network: lo0 awg0.
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
        options=600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6>
        inet6 ::1 prefixlen 128
        inet6 fe80::1%lo0 prefixlen 64 scopeid 0xawg0: link state changed
to DOWN
awg0: link state changed to UP
2
        inet 127.0.0.1 netmask 0xff000000
        groups: lo
        nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
awg0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=8000b<RXCSUM,TXCSUM,VLAN_MTU,LINKSTATE>
        ether 02:81:ae:83:0f:fa
        media: Ethernet none (none <hw-loopback>)
        status: active
        nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
Starting devd.
Starting Network: awg0.
awg0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=8000b<RXCSUM,TXCSUM,VLAN_MTU,LINKSTATE>
        ether 02:81:ae:83:0f:fa
        media: Ethernet none (none <hw-loopback>)
        status: active
        nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
add host 127.0.0.1: gateway lo0 fib 0: route already in table
add host ::1: gateway lo0 fib 0: route already in table
add net fe80::: gateway ::1
add net ff02::: gateway ::1
add net ::ffff:0.0.0.0: gateway ::1
add net ::0.0.0.0: gateway ::1
Generating host.conf.
Creating and/or trimming log files.
Starting syslogd.
Clearing /tmp (X related).
Updating motd:.
Mounting late filesystems:.
Starting sendmail_submit.
Starting sendmail_msp_queue.
Starting cron.
Starting background file system checks in 60 seconds.

Tue Jan 16 14:06:53 UTC 2018

FreeBSD/arm (head_pi) (ttyu0)

login:

2018-01-16 9:52 GMT+08:00 Kyle Evans <kevans at freebsd.org>:

> On Mon, Jan 15, 2018 at 7:30 PM, 阿金 <unto.foru13 at gmail.com> wrote:
> > Thanks Mark,head -r327485  is good
> > no more pte2 errors(I also change another sd card test).
> > I have network ,and can make ports in orange pi one.
> > I will live with -r327485.
> >
> > just remind  ,I try new revision 327807,will got network error .
> >
> > awg0: <Allwinner Gigabit Ethernet> mem 0x1c30000-0x1c30103,0x1c00030-
> 0x1c00033
> > irq 23 on simplebus0
> > awg0: cannot get tx clock
> > miibus0: <MII bus> on awg0
> >
>
> What does the rest of your dmesg reveal? Did it try to attach a
> syscon_generic sometime before there for some reason?
>
> Thanks,
>
> Kyle Evans
>