Few issues with Marvell code
Tarick
tungan at ukr.net
Sat Jul 2 12:23:37 UTC 2011
> ---------------------------------------------------------------------
>
> Message: 1
> Date: Fri, 1 Jul 2011 02:25:45 +0200
> From: Damjan Marion <damjan.marion at gmail.com>
> Subject: Re: Few issues with Marvell code
> To: Kevin Lo <kevlo at kevlo.org>
> Cc: freebsd-arm at freebsd.org
> Message-ID: <6F62AF96-4631-4F97-80CF-959A6C373446 at gmail.com>
> Content-Type: text/plain; charset=us-ascii
>
>
> On Jun 29, 2011, at 11:59 AM, Kevin Lo wrote:
>
> >
> > I tried to boot kernel.bin used the generic DB-88F5XXX kernel
> > configuration on the 88F5182 board, it doesn't work either.
> > I will further investigate.
>
> Where it stops?
>
> Damjan
>
>
> ------------------------------
>
> Message: 2
> Date: Fri, 01 Jul 2011 14:42:55 +0800
> From: Kevin Lo <kevlo at kevlo.org>
> Subject: Re: Few issues with Marvell code
> To: Damjan Marion <damjan.marion at gmail.com>
> Cc: freebsd-arm at freebsd.org
> Message-ID: <1309502575.7757.2.camel at srgsec>
> Content-Type: text/plain; charset="Big5"
>
> On Fri, 2011-07-01 at 02:25 +0200, Damjan Marion wrote:
> > On Jun 29, 2011, at 11:59 AM, Kevin Lo wrote:
> >
> > >
> > > I tried to boot kernel.bin used the generic DB-88F5XXX kernel
> > > configuration on the 88F5182 board, it doesn't work either.
> > > I will further investigate.
> >
> > Where it stops?
>
> === BUFFALO LS-GL U-Boot. ===
> ** LOADER **
> ** BUFFALO BOARD: BUFFALO_BOARD_LS_GL LE
>
> U-Boot 1.1.1 (Jun 12 2006 - 10:32:00) Marvell version: 1.10.8
>
> DRAM CS[0] base 0x00000000 size 128MB
> DRAM Total size 128MB
> [256kB at fffc0000] [0kB at f8000000] ## Unknown FLASH at f8000000: Size =
> 0x00000000B
> Flash: 256 kB
> Addresses 20M - 0M are saved for the U-Boot usage.
> Mem malloc Initialization (20M - 16M): Done
>
> Soc: 88F5182
> A2
> CPU: ARM926 (Rev 0) running @
> 400Mhz
> Orion 1 streaming
> disabled
> SysClock = 200Mhz , TClock =
> 166Mhz
>
>
> USB 0: host
> mode
> USB 1: host
> mode
> PCI 0: PCI Express Root Complex
> Interface
> PCI 1: Conventional PCI, speed =
> 33000000
> Net: egiga0
> [PRIME]
>
> Marvell Serial ATA
> Adapter
> Intergrated Sata device
> found
>
> <<can_not_mount>>
> HDD is not
> found
> hit any key to switch tftp
> boot.
> Hit any key to stop autoboot:
> 0
> Marvell>> tftpboot 900000
> mv5281/kernel.bin
> Using egiga0
> device
> TFTP from server 172.16.113.84; our IP address is
> 172.16.113.8
> Filename
> 'mv5281/kernel.bin'.
> Load address:
> 0x900000
> Loading:
> #################################################################
>
> #################################################################
>
> #################################################################
>
> #################################################################
>
> #################################################################
>
> #################################################################
>
> #################################################################
>
> #################################################################
>
> #################################################################
>
> #################################
> done
> Bytes transferred = 3162744 (304278
> hex)
> Marvell>> go
> 900000
> ## Starting application at
> 0x00900000 ...
>
> Scary, eh?
>
> > Damjan
>
> Kevin
Sorry, I messed up with the subject line, so re-posting again.
Please look at http://www.freebsd.org/cgi/query-pr.cgi?pr=arm%2F156814&cat=
I have OpenRD Ultimate, which is actually from DB-88F6XXX, but the kernel from current failed to load with the same message. Using the patch from PR I was able to boot successfully.
More information about the freebsd-arm
mailing list